CommandStation-EX/IO_I2CRailcom.h

   /*
 *  © 2024, Chris Harlow. All rights reserved.
 *  © 2023, Neil McKechnie. All rights reserved.
 *  
 *  This file is part of DCC++EX API
 *
 *  This is free software: you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation, either version 3 of the License, or
 *  (at your option) any later version.
 *
 *  It is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
 */

/*
 * 
 * Dec 2023, Added NXP SC16IS752 I2C Dual UART
 * The SC16IS752 has 64 bytes TX & RX FIFO buffer
 * First version without interrupts from I2C UART and only RX/TX are used, interrupts may not be
 * needed as the RX Fifo holds the reply 
 * 
 * Jan 2024, Issue with using both UARTs simultaniously, the secod uart seems to work  but the first transmit 
 * corrupt data. This need more analysis and experimenatation. 
 * Will push this driver to the dev branch with the uart fixed to 0 
 * Both SC16IS750 (single uart) and SC16IS752 (dual uart, but only uart 0 is enable)
 * 
 * myHall.cpp configuration syntax:
 * 
 * I2CRailcom::create(1st vPin, vPins, I2C address, xtal);
 * 
 * Parameters:
 * 1st vPin     : First virtual pin that EX-Rail can control to play a sound, use PLAYSOUND command (alias of ANOUT)
 * vPins        : Total number of virtual pins allocated (2 vPins are supported, one for each UART)
 *                1st vPin for UART 0, 2nd for UART 1
 * I2C Address  : I2C address of the serial controller, in 0x format
 */

#ifndef IO_I2CRailcom_h
#define IO_I2CRailcom_h

#include "IODevice.h"
#include "I2CManager.h"
#include "DIAG.h"

// Debug and diagnostic defines, enable too many will result in slowing the driver
#define DIAG_I2CRailcom
#define DIAG_I2CRailcom_data
#define DIAG_I2CRailcom_reg

class I2CRailcom : public IODevice {
private: 
  // SC16IS752 defines
  uint8_t _UART_CH=0x00; 
  // Communication parameters for the DFPlayer are fixed at 8 bit, No parity, 1 stopbit
  const uint8_t WORD_LEN = 0x03;    // Value LCR bit 0,1
  const uint8_t STOP_BIT = 0x00;    // Value LCR bit 2 
  const uint8_t PARITY_ENA = 0x00;  // Value LCR bit 3
  const  uint8_t PARITY_TYPE = 0x00; // Value LCR bit 4
  const uint32_t BAUD_RATE = 9600;
  const  uint8_t PRESCALER = 0x01;   // Value MCR bit 7  
  const unsigned long SC16IS752_XTAL_FREQ_RAILCOM = 16000000; // Baud rate for Railcom signal
  byte _inbuf[65];
  byte _outbuf[2]; 
public:
  // Constructor
   I2CRailcom(VPIN firstVpin, int nPins, I2CAddress i2cAddress){
    _firstVpin = firstVpin;
    _nPins = nPins;
    _I2CAddress = i2cAddress;
    addDevice(this);
   } 
  
public:
  static void create(VPIN firstVpin, int nPins, I2CAddress i2cAddress) {
    if (nPins>2) nPins=2;
    if (checkNoOverlap(firstVpin, nPins, i2cAddress)) 
     new I2CRailcom(firstVpin, nPins, i2cAddress); 
    }

  void _begin() override {
    I2CManager.setClock(1000000); // TODO do we need this?
    I2CManager.begin();
    auto exists=I2CManager.exists(_I2CAddress);
    DIAG(F("I2CRailcom: %s UART%S detected"), 
           _I2CAddress.toString(), exists?F(""):F(" NOT"));
    if (!exists) return;
    
    _UART_CH=0;
    Init_SC16IS752(); // Initialize UART0
    if (_nPins>1) {
      _UART_CH=1;
      Init_SC16IS752(); // Initialize UART1
    }
    if (_deviceState==DEVSTATE_INITIALISING) _deviceState=DEVSTATE_NORMAL;
    _display();
    }
  
  
  void _loop(unsigned long currentMicros) override {
    // Read responses from device
    if (_deviceState!=DEVSTATE_NORMAL) return;

    // TODO - return if in cutout or cutout very soon.  
    
    // flip channels each loop
    if (_nPins>1) _UART_CH=_UART_CH?0:1;

    // Read incoming raw Railcom data, and process accordingly
    auto inlength= UART_ReadRegister(REG_RXLV);
    if (inlength==0) return; 
    {
        #ifdef DIAG_I2CRailcom
          DIAG(F("Railcom: %s/%d RX Fifo: %d"),_I2CAddress.toString(), _UART_CH, inlength); 
        #endif
        _outbuf[0]=(byte)(REG_RHR << 3 | _UART_CH << 1);
        I2CManager.read(_I2CAddress, _inbuf, inlength, _outbuf, 1); 
        #ifdef DIAG_I2CRailcom_data
          DIAG(F("Railcom %s/%d RX FIFO Data"), _I2CAddress.toString(), _UART_CH);
          for (int i = 0; i < inlength; i++){
            DIAG(F("[0x%x]: 0x%x"), i, _inbuf[i]);  
          }
        #endif       
    } 
    
  }

  
  void _display() override {
    DIAG(F("I2CRailcom Configured on Vpins:%u-%u %S"), _firstVpin, _firstVpin+_nPins-1,
      (_deviceState!=DEVSTATE_NORMAL) ? F("OFFLINE") : F(""));
  }
  
private: 


  // SC16IS752 functions
  // Initialise SC16IS752 only for this channel
  // First a software reset
  // Enable FIFO and clear TX & RX FIFO
  // Need to set the following registers
  // IOCONTROL set bit 1 and 2 to 0 indicating that they are GPIO
  // IODIR set all bit to 1 indicating al are output
  // IOSTATE set only bit 0 to 1 for UART 0, or only bit 1 for UART 1  // 
  // LCR bit 7=0 divisor latch (clock division registers DLH & DLL, they store 16 bit divisor), 
  //     WORD_LEN, STOP_BIT, PARITY_ENA and PARITY_TYPE
  // MCR bit 7=0 clock divisor devide-by-1 clock input
  // DLH most significant part of divisor
  // DLL least significant part of divisor
  //
  // BAUD_RATE, WORD_LEN, STOP_BIT, PARITY_ENA and PARITY_TYPE have been defined and initialized
  // 
  void Init_SC16IS752(){ 
    //uint16_t _divisor = (SC16IS752_XTAL_FREQ / PRESCALER) / (BAUD_RATE * 16);
    const uint16_t _divisor = (SC16IS752_XTAL_FREQ_RAILCOM / PRESCALER) / (BAUD_RATE * 16);  // Calculate _divisor for baudrate
    
    if (_UART_CH==0) {
      // only reset on channel 0}
      UART_WriteRegister(REG_IOCONTROL, 0x08,false); // UART Software reset
       _deviceState=DEVSTATE_INITIALISING;  // ignores error during reset which seems normal.
   } 
  
    UART_WriteRegister(REG_FCR, 0x07,false); // Reset FIFO, clear RX & TX FIFO (write only)
    UART_WriteRegister(REG_MCR, 0x00); // Set MCR to all 0, includes Clock divisor
    UART_WriteRegister(REG_LCR, 0x80 | WORD_LEN | STOP_BIT | PARITY_ENA | PARITY_TYPE); // Divisor latch enabled
    UART_WriteRegister(REG_DLL, _divisor);  // Write DLL
    UART_WriteRegister(REG_DLH, (uint8_t)(_divisor >> 8)); // Write DLH
    UART_WriteRegister(REG_LCR, UART_ReadRegister(REG_LCR) & 0x7F); // Divisor latch disabled
    if (_deviceState==DEVSTATE_INITIALISING) {
      DIAG(F("UART %d init complete"),_UART_CH);
    }  
  }

  
  

  void UART_WriteRegister(uint8_t reg, uint8_t val, bool readback=true){
    _outbuf[0] = (byte)( reg << 3 | _UART_CH << 1);
    _outbuf[1]=val;
    auto status=I2CManager.write(_I2CAddress, _outbuf, (uint8_t)2);
    if(status!=I2C_STATUS_OK) {
      DIAG(F("I2CRailcom %s/%d write reg=0x%x,data=0x%x,I2Cstate=%d"),
       _I2CAddress.toString(), _UART_CH, reg, val, status);
       _deviceState=DEVSTATE_FAILED;
    }
    if (readback) {    // Read it back to cross check
      auto readback=UART_ReadRegister(reg);
      if (readback!=val) {
        DIAG(F("I2CRailcom %s/%d reg:0x%x write=0x%x read=0x%x"),_I2CAddress.toString(),_UART_CH,reg,val,readback);
      }
    }
  }

 
  uint8_t UART_ReadRegister(uint8_t reg){
     _outbuf[0] = (byte)(reg << 3 | _UART_CH << 1); // _outbuffer[0] has now UART_REG and UART_CH
     _inbuf[0]=0;
     auto status=I2CManager.read(_I2CAddress, _inbuf, 1, _outbuf, 1);    
    if (status!=I2C_STATUS_OK) {
       DIAG(F("I2CRailcom %s/%d read reg=0x%x,I2Cstate=%d"),
       _I2CAddress.toString(), _UART_CH, reg, status);  
       _deviceState=DEVSTATE_FAILED;
    }
    return _inbuf[0]; 
  }

// SC16IS752 General register set (from the datasheet)
enum : uint8_t {
    REG_RHR       = 0x00, // FIFO Read
    REG_THR       = 0x00, // FIFO Write
    REG_IER       = 0x01, // Interrupt Enable Register R/W
    REG_FCR       = 0x02, // FIFO Control Register Write
    REG_IIR       = 0x02, // Interrupt Identification Register Read
    REG_LCR       = 0x03, // Line Control Register R/W
    REG_MCR       = 0x04, // Modem Control Register R/W
    REG_LSR       = 0x05, // Line Status Register Read
    REG_MSR       = 0x06, // Modem Status Register Read
    REG_SPR       = 0x07, // Scratchpad Register R/W
    REG_TCR       = 0x06, // Transmission Control Register R/W
    REG_TLR       = 0x07, // Trigger Level Register R/W    
    REG_TXLV      = 0x08, // Transmitter FIFO Level register Read
    REG_RXLV      = 0x09, // Receiver FIFO Level register Read
    REG_IODIR     = 0x0A, // Programmable I/O pins Direction register R/W
    REG_IOSTATE   = 0x0B, // Programmable I/O pins State register R/W
    REG_IOINTENA  = 0x0C, // I/O Interrupt Enable register R/W
    REG_IOCONTROL = 0x0E, // I/O Control register R/W
    REG_EFCR      = 0x0F, // Extra Features Control Register R/W
  };

// SC16IS752 Special register set
enum : uint8_t{
    REG_DLL       = 0x00, // Division registers R/W
    REG_DLH       = 0x01, // Division registers R/W
  };

// SC16IS752 Enhanced regiter set
enum : uint8_t{
    REG_EFR       = 0X02, // Enhanced Features Register R/W
    REG_XON1      = 0x04, // R/W
    REG_XON2      = 0x05, // R/W
    REG_XOFF1     = 0x06, // R/W
    REG_XOFF2     = 0x07, // R/W
  };

};

#endif // IO_I2CRailcom_h