mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-30 03:26:13 +01:00
Merge branch 'devel-stm32-cmri' into devel-ash-temp0108
This commit is contained in:
Ash-4
GitHub
commit
268650a218
|
|
@ -56,9 +56,9 @@ HardwareSerial Serial5(PD2, PC12); // Rx=PD2, Tx=PC12 -- UART5 - F446RE
|
|||
defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F439ZI)
|
||||
// Nucleo-144 boards don't have Serial1 defined by default
|
||||
HardwareSerial Serial6(PG9, PG14); // Rx=PG9, Tx=PG14 -- USART6
|
||||
HardwareSerial Serial5(PD2, PC12); // Rx=PD2, Tx=PC12 -- UART5
|
||||
#if !defined(ARDUINO_NUCLEO_F412ZG)
|
||||
HardwareSerial Serial2(PD6, PD5); // Rx=PD6, Tx=PD5 -- UART5
|
||||
HardwareSerial Serial2(PD6, PD5); // Rx=PD6, Tx=PD5 -- UART2
|
||||
#if !defined(ARDUINO_NUCLEO_F412ZG) // F412ZG does not have UART5
|
||||
HardwareSerial Serial5(PD2, PC12); // Rx=PD2, Tx=PC12 -- UART5
|
||||
#endif
|
||||
// Serial3 is defined to use USART3 by default, but is in fact used as the diag console
|
||||
// via the debugger on the Nucleo-144. It is therefore unavailable for other DCC-EX uses like WiFi, DFPlayer, etc.
|
||||
|
|
|
|||
|
|
@ -41,8 +41,11 @@ void EthernetInterface::setup()
|
|||
DIAG(F("Prog Error!"));
|
||||
return;
|
||||
}
|
||||
if ((singleton=new EthernetInterface()))
|
||||
DIAG(F("Ethernet Class setup, attempting to instantiate"));
|
||||
if ((singleton=new EthernetInterface())) {
|
||||
DIAG(F("Ethernet Class initialized"));
|
||||
return;
|
||||
}
|
||||
DIAG(F("Ethernet not initialized"));
|
||||
};
|
||||
|
||||
|
|
@ -55,24 +58,48 @@ void EthernetInterface::setup()
|
|||
*/
|
||||
EthernetInterface::EthernetInterface()
|
||||
{
|
||||
byte mac[6];
|
||||
DCCTimer::getSimulatedMacAddress(mac);
|
||||
connected=false;
|
||||
|
||||
#ifdef IP_ADDRESS
|
||||
if (Ethernet.begin(mac, IP_ADDRESS) == 0)
|
||||
#else
|
||||
if (Ethernet.begin(mac) == 0)
|
||||
#endif
|
||||
#if defined(STM32_ETHERNET)
|
||||
// Set a HOSTNAME for the DHCP request - a nice to have, but hard it seems on LWIP for STM32
|
||||
// The default is "lwip", which is **always** set in STM32Ethernet/src/utility/ethernetif.cpp
|
||||
// for some reason. One can edit it to instead read:
|
||||
// #if LWIP_NETIF_HOSTNAME
|
||||
// /* Initialize interface hostname */
|
||||
// if (netif->hostname == NULL)
|
||||
// netif->hostname = "lwip";
|
||||
// #endif /* LWIP_NETIF_HOSTNAME */
|
||||
// Which seems more useful! We should propose the patch... so the following line actually works!
|
||||
netif_set_hostname(&gnetif, WIFI_HOSTNAME); // Should probably be passed in the contructor...
|
||||
#ifdef IP_ADDRESS
|
||||
if (Ethernet.begin(IP_ADDRESS) == 0)
|
||||
#else
|
||||
if (Ethernet.begin() == 0)
|
||||
#endif // IP_ADDRESS
|
||||
{
|
||||
DIAG(F("Ethernet.begin FAILED"));
|
||||
return;
|
||||
}
|
||||
#else // All other architectures
|
||||
byte mac[6]= { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
|
||||
DIAG(F("Ethernet attempting to get MAC address"));
|
||||
DCCTimer::getSimulatedMacAddress(mac);
|
||||
DIAG(F("Ethernet got MAC address"));
|
||||
#ifdef IP_ADDRESS
|
||||
if (Ethernet.begin(mac, IP_ADDRESS) == 0)
|
||||
#else
|
||||
if (Ethernet.begin(mac) == 0)
|
||||
#endif
|
||||
{
|
||||
DIAG(F("Ethernet.begin FAILED"));
|
||||
return;
|
||||
}
|
||||
|
||||
if (Ethernet.hardwareStatus() == EthernetNoHardware) {
|
||||
DIAG(F("Ethernet shield not found or W5100"));
|
||||
}
|
||||
#endif
|
||||
|
||||
unsigned long startmilli = millis();
|
||||
uint32_t startmilli = millis();
|
||||
while ((millis() - startmilli) < 5500) { // Loop to give time to check for cable connection
|
||||
if (Ethernet.linkStatus() == LinkON)
|
||||
break;
|
||||
|
|
@ -171,17 +198,25 @@ void EthernetInterface::loop2() {
|
|||
return;
|
||||
}
|
||||
// get client from the server
|
||||
#if defined (STM32_ETHERNET)
|
||||
// STM32Ethernet doesn't use accept(), just available()
|
||||
EthernetClient client = server->available();
|
||||
#else
|
||||
EthernetClient client = server->accept();
|
||||
|
||||
#endif
|
||||
// check for new client
|
||||
if (client)
|
||||
{
|
||||
if (Diag::ETHERNET) DIAG(F("Ethernet: New client "));
|
||||
byte socket;
|
||||
for (socket = 0; socket < MAX_SOCK_NUM; socket++)
|
||||
{
|
||||
if (!clients[socket])
|
||||
if (clients[socket]) {
|
||||
if (clients[socket] == client)
|
||||
break;
|
||||
}
|
||||
else //if (!clients[socket])
|
||||
{
|
||||
if (Diag::ETHERNET) DIAG(F("Ethernet: New client "));
|
||||
// On accept() the EthernetServer doesn't track the client anymore
|
||||
// so we store it in our client array
|
||||
if (Diag::ETHERNET) DIAG(F("Socket %d"),socket);
|
||||
|
|
|
|||
|
|
@ -35,8 +35,18 @@
|
|||
#if defined (ARDUINO_TEENSY41)
|
||||
#include <NativeEthernet.h> //TEENSY Ethernet Treiber
|
||||
#include <NativeEthernetUdp.h>
|
||||
#define MAX_SOCK_NUM 4
|
||||
#elif defined (ARDUINO_NUCLEO_F429ZI) || defined (ARDUINO_NUCLEO_F439ZI)
|
||||
#include <LwIP.h>
|
||||
// #include "STM32lwipopts.h"
|
||||
#include <STM32Ethernet.h>
|
||||
#include <lwip/netif.h>
|
||||
extern "C" struct netif gnetif;
|
||||
#define STM32_ETHERNET
|
||||
#define MAX_SOCK_NUM 10
|
||||
#else
|
||||
#include "Ethernet.h"
|
||||
#define MAX_SOCK_NUM 4
|
||||
#endif
|
||||
#include "RingStream.h"
|
||||
|
||||
|
|
|
|||
|
|
@ -54,6 +54,8 @@ static const FSH * guessI2CDeviceType(uint8_t address) {
|
|||
return F("Time-of-flight sensor");
|
||||
else if (address >= 0x3c && address <= 0x3d)
|
||||
return F("OLED Display");
|
||||
else if (address >= 0x48 && address <= 0x57) // Henkk: Added SC16IS752 UART detection
|
||||
return F("SC16IS752 UART");
|
||||
else if (address >= 0x48 && address <= 0x4f)
|
||||
return F("Analogue Inputs or PWM");
|
||||
else if (address >= 0x40 && address <= 0x4f)
|
||||
|
|
@ -64,6 +66,7 @@ static const FSH * guessI2CDeviceType(uint8_t address) {
|
|||
return F("Real-time clock");
|
||||
else if (address >= 0x70 && address <= 0x77)
|
||||
return F("I2C Mux");
|
||||
else if (address >= 0x90 && address <= 0xAE);
|
||||
else
|
||||
return F("?");
|
||||
}
|
||||
|
|
|
|||
|
|
@ -39,7 +39,7 @@
|
|||
#if defined(I2C_USE_INTERRUPTS) && defined(ARDUINO_ARCH_STM32)
|
||||
#if defined(ARDUINO_NUCLEO_F401RE) || defined(ARDUINO_NUCLEO_F411RE) || defined(ARDUINO_NUCLEO_F446RE) \
|
||||
|| defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F413ZH) \
|
||||
|| defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
|
||||
|| defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F439ZI) || defined(ARDUINO_NUCLEO_F446ZE)
|
||||
// Assume I2C1 for now - default I2C bus on Nucleo-F411RE and likely all Nucleo-64
|
||||
// and Nucleo-144 variants
|
||||
I2C_TypeDef *s = I2C1;
|
||||
|
|
|
|||
|
|
@ -22,7 +22,8 @@
|
|||
#define iodevice_h
|
||||
|
||||
// Define symbol DIAG_IO to enable diagnostic output
|
||||
//#define DIAG_IO Y
|
||||
//#define DIAG_IO
|
||||
|
||||
|
||||
// Define symbol DIAG_LOOPTIMES to enable CS loop execution time to be reported
|
||||
//#define DIAG_LOOPTIMES
|
||||
|
|
|
|||
316
IO_CMRI.cpp
Normal file
316
IO_CMRI.cpp
Normal file
|
|
@ -0,0 +1,316 @@
|
|||
/*
|
||||
* © 2023, Neil McKechnie. All rights reserved.
|
||||
*
|
||||
* This file is part of DCC++EX API
|
||||
*
|
||||
* This is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* It is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with CommandStation. If not, see <https://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "IO_CMRI.h"
|
||||
#include "defines.h"
|
||||
|
||||
/************************************************************
|
||||
* CMRIbus implementation
|
||||
************************************************************/
|
||||
|
||||
// Constructor for CMRIbus
|
||||
CMRIbus::CMRIbus(uint8_t busNo, HardwareSerial &serial, unsigned long baud, uint16_t cycleTimeMS, VPIN transmitEnablePin) {
|
||||
_busNo = busNo;
|
||||
_serial = &serial;
|
||||
_baud = baud;
|
||||
_cycleTime = cycleTimeMS * 1000UL; // convert from milliseconds to microseconds.
|
||||
_transmitEnablePin = transmitEnablePin;
|
||||
if (_transmitEnablePin != VPIN_NONE) {
|
||||
pinMode(_transmitEnablePin, OUTPUT);
|
||||
ArduinoPins::fastWriteDigital(_transmitEnablePin, 0); // transmitter initially off
|
||||
}
|
||||
|
||||
// Max message length is 256+6=262 bytes.
|
||||
// Each byte is one start bit, 8 data bits and 1 or 2 stop bits, assume 11 bits per byte.
|
||||
// Calculate timeout based on treble this time.
|
||||
_timeoutPeriod = 3 * 11 * 262 * 1000UL / (_baud / 1000UL);
|
||||
#if defined(ARDUINOCMRI_COMPATIBLE)
|
||||
// NOTE: The ArduinoCMRI library, unless modified, contains a 'delay(50)' between
|
||||
// receiving the end of the prompt message and starting to send the response. This
|
||||
// is allowed for below.
|
||||
_timeoutPeriod += 50000UL;
|
||||
#endif
|
||||
|
||||
// Calculate the time in microseconds to transmit one byte (11 bits max).
|
||||
_byteTransmitTime = 1000000UL * 11 / _baud;
|
||||
// Postdelay is only required if we need to allow for data still being sent when
|
||||
// we want to switch off the transmitter. The flush() method of HardwareSerial
|
||||
// ensures that the data has completed being sent over the line.
|
||||
_postDelay = 0;
|
||||
|
||||
// Add device to HAL device chain
|
||||
IODevice::addDevice(this);
|
||||
|
||||
// Add bus to CMRIbus chain.
|
||||
_nextBus = _busList;
|
||||
_busList = this;
|
||||
}
|
||||
|
||||
|
||||
// Main loop function for CMRIbus.
|
||||
// Work through list of nodes. For each node, in separate loop entries
|
||||
// send initialisation message (once only); then send
|
||||
// output message; then send prompt for input data, and
|
||||
// process any response data received.
|
||||
// When the slot time has finished, move on to the next device.
|
||||
void CMRIbus::_loop(unsigned long currentMicros) {
|
||||
|
||||
_currentMicros = currentMicros;
|
||||
|
||||
while (_serial->available())
|
||||
processIncoming();
|
||||
|
||||
// Send any data that needs sending.
|
||||
processOutgoing();
|
||||
|
||||
}
|
||||
|
||||
// Send output data to the bus for nominated CMRInode
|
||||
uint16_t CMRIbus::sendData(CMRInode *node) {
|
||||
uint16_t numDataBytes = (node->getNumOutputs()+7)/8;
|
||||
_serial->write(SYN);
|
||||
_serial->write(SYN);
|
||||
_serial->write(STX);
|
||||
_serial->write(node->getAddress() + 65);
|
||||
_serial->write('T'); // T for Transmit data message
|
||||
uint16_t charsSent = 6; // include header and trailer
|
||||
for (uint8_t index=0; index<numDataBytes; index++) {
|
||||
uint8_t value = node->getOutputStates(index);
|
||||
if (value == DLE || value == STX || value == ETX) {
|
||||
_serial->write(DLE);
|
||||
charsSent++;
|
||||
}
|
||||
_serial->write(value);
|
||||
charsSent++;
|
||||
}
|
||||
_serial->write(ETX);
|
||||
return charsSent; // number of characters sent
|
||||
}
|
||||
|
||||
// Send request for input data to nominated CMRInode.
|
||||
uint16_t CMRIbus::requestData(CMRInode *node) {
|
||||
_serial->write(SYN);
|
||||
_serial->write(SYN);
|
||||
_serial->write(STX);
|
||||
_serial->write(node->getAddress() + 65);
|
||||
_serial->write('P'); // P for Poll message
|
||||
_serial->write(ETX);
|
||||
return 6; // number of characters sent
|
||||
}
|
||||
|
||||
// Send initialisation message
|
||||
uint16_t CMRIbus::sendInitialisation(CMRInode *node) {
|
||||
_serial->write(SYN);
|
||||
_serial->write(SYN);
|
||||
_serial->write(STX);
|
||||
_serial->write(node->getAddress() + 65);
|
||||
_serial->write('I'); // I for initialise message
|
||||
_serial->write(node->getType()); // NDP
|
||||
_serial->write((uint8_t)0); // dH
|
||||
_serial->write((uint8_t)0); // dL
|
||||
_serial->write((uint8_t)0); // NS
|
||||
_serial->write(ETX);
|
||||
return 10; // number of characters sent
|
||||
}
|
||||
|
||||
void CMRIbus::processOutgoing() {
|
||||
uint16_t charsSent = 0;
|
||||
if (_currentNode == NULL) {
|
||||
// If we're between read/write cycles then don't do anything else.
|
||||
if (_currentMicros - _cycleStartTime < _cycleTime) return;
|
||||
// ... otherwise start processing the first node in the list
|
||||
_currentNode = _nodeListStart;
|
||||
_transmitState = TD_INIT;
|
||||
_cycleStartTime = _currentMicros;
|
||||
}
|
||||
if (_currentNode == NULL) return;
|
||||
switch (_transmitState) {
|
||||
case TD_IDLE:
|
||||
case TD_INIT:
|
||||
enableTransmitter();
|
||||
if (!_currentNode->isInitialised()) {
|
||||
charsSent = sendInitialisation(_currentNode);
|
||||
_currentNode->setInitialised();
|
||||
_transmitState = TD_TRANSMIT;
|
||||
delayUntil(_currentMicros+_byteTransmitTime*charsSent);
|
||||
break;
|
||||
}
|
||||
/* fallthrough */
|
||||
case TD_TRANSMIT:
|
||||
charsSent = sendData(_currentNode);
|
||||
_transmitState = TD_PROMPT;
|
||||
// Defer next entry for as long as it takes to transmit the characters,
|
||||
// to allow output queue to empty. Allow 2 bytes extra.
|
||||
delayUntil(_currentMicros+_byteTransmitTime*(charsSent+2));
|
||||
break;
|
||||
case TD_PROMPT:
|
||||
charsSent = requestData(_currentNode);
|
||||
disableTransmitter();
|
||||
_transmitState = TD_RECEIVE;
|
||||
_timeoutStart = _currentMicros; // Start timeout on response
|
||||
break;
|
||||
case TD_RECEIVE: // Waiting for response / timeout
|
||||
if (_currentMicros - _timeoutStart > _timeoutPeriod) {
|
||||
// End of time slot allocated for responses.
|
||||
_transmitState = TD_IDLE;
|
||||
// Reset state of receiver
|
||||
_receiveState = RD_SYN1;
|
||||
// Move to next node
|
||||
_currentNode = _currentNode->getNext();
|
||||
}
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
// Process any data bytes received from a CMRInode.
|
||||
void CMRIbus::processIncoming() {
|
||||
int data = _serial->read();
|
||||
if (data < 0) return; // No characters to read
|
||||
|
||||
if (_transmitState != TD_RECEIVE || !_currentNode) return; // Not waiting for input, so ignore.
|
||||
|
||||
uint8_t nextState = RD_SYN1; // default to resetting state machine
|
||||
switch(_receiveState) {
|
||||
case RD_SYN1:
|
||||
if (data == SYN) nextState = RD_SYN2;
|
||||
break;
|
||||
case RD_SYN2:
|
||||
if (data == SYN) nextState = RD_STX; else nextState = RD_SYN2;
|
||||
break;
|
||||
case RD_STX:
|
||||
if (data == STX) nextState = RD_ADDR;
|
||||
break;
|
||||
case RD_ADDR:
|
||||
// If address doesn't match, then ignore everything until next SYN-SYN-STX.
|
||||
if (data == _currentNode->getAddress() + 65) nextState = RD_TYPE;
|
||||
break;
|
||||
case RD_TYPE:
|
||||
_receiveDataIndex = 0; // Initialise data pointer
|
||||
if (data == 'R') nextState = RD_DATA;
|
||||
break;
|
||||
case RD_DATA: // data body
|
||||
if (data == DLE) // escape next character
|
||||
nextState = RD_ESCDATA;
|
||||
else if (data == ETX) { // end of data
|
||||
// End of data message. Protocol has all data in one
|
||||
// message, so we don't need to wait any more. Allow
|
||||
// transmitter to proceed with next node in list.
|
||||
_currentNode = _currentNode->getNext();
|
||||
_transmitState = TD_IDLE;
|
||||
} else {
|
||||
// Not end yet, so save data byte
|
||||
_currentNode->saveIncomingData(_receiveDataIndex++, data);
|
||||
nextState = RD_DATA; // wait for more data
|
||||
}
|
||||
break;
|
||||
case RD_ESCDATA: // escaped data byte
|
||||
_currentNode->saveIncomingData(_receiveDataIndex++, data);
|
||||
nextState = RD_DATA;
|
||||
break;
|
||||
}
|
||||
_receiveState = nextState;
|
||||
}
|
||||
|
||||
// If configured for half duplex RS485, switch RS485 interface
|
||||
// into transmit mode.
|
||||
void CMRIbus::enableTransmitter() {
|
||||
if (_transmitEnablePin != VPIN_NONE)
|
||||
ArduinoPins::fastWriteDigital(_transmitEnablePin, 1);
|
||||
// If we need a delay before we start the packet header,
|
||||
// we can send a character or two to synchronise the
|
||||
// transmitter and receiver.
|
||||
// SYN characters should be used, but a bug in the
|
||||
// ArduinoCMRI library causes it to ignore the packet if
|
||||
// it's preceded by an odd number of SYN characters.
|
||||
// So send a SYN followed by a NUL in that case.
|
||||
_serial->write(SYN);
|
||||
#if defined(ARDUINOCMRI_COMPATIBLE)
|
||||
_serial->write(NUL); // Reset the ArduinoCMRI library's parser
|
||||
#endif
|
||||
}
|
||||
|
||||
// If configured for half duplex RS485, switch RS485 interface
|
||||
// into receive mode.
|
||||
void CMRIbus::disableTransmitter() {
|
||||
// Wait until all data has been transmitted. On the standard
|
||||
// AVR driver, this waits until the FIFO is empty and all
|
||||
// data has been sent over the link.
|
||||
_serial->flush();
|
||||
// If we don't trust the 'flush' function and think the
|
||||
// data's still in transit, then wait a bit longer.
|
||||
if (_postDelay > 0)
|
||||
delayMicroseconds(_postDelay);
|
||||
// Hopefully, we can now safely switch off the transmitter.
|
||||
if (_transmitEnablePin != VPIN_NONE)
|
||||
ArduinoPins::fastWriteDigital(_transmitEnablePin, 0);
|
||||
}
|
||||
|
||||
// Link to chain of CMRI bus instances
|
||||
CMRIbus *CMRIbus::_busList = NULL;
|
||||
|
||||
|
||||
/************************************************************
|
||||
* CMRInode implementation
|
||||
************************************************************/
|
||||
|
||||
// Constructor for CMRInode object
|
||||
CMRInode::CMRInode(VPIN firstVpin, int nPins, uint8_t busNo, uint8_t address, char type, uint16_t inputs, uint16_t outputs) {
|
||||
_firstVpin = firstVpin;
|
||||
_nPins = nPins;
|
||||
_busNo = busNo;
|
||||
_address = address;
|
||||
_type = type;
|
||||
|
||||
switch (_type) {
|
||||
case 'M': // SMINI, fixed 24 inputs and 48 outputs
|
||||
_numInputs = 24;
|
||||
_numOutputs = 48;
|
||||
break;
|
||||
case 'C': // CPNODE with 16 to 144 inputs/outputs using 8-bit cards
|
||||
_numInputs = inputs;
|
||||
_numOutputs = outputs;
|
||||
break;
|
||||
case 'N': // Classic USIC and SUSIC using 24 bit i/o cards
|
||||
case 'X': // SUSIC using 32 bit i/o cards
|
||||
default:
|
||||
DIAG(F("CMRInode: bus:%d address:%d ERROR unsupported type %c"), _busNo, _address, _type);
|
||||
return; // Don't register device.
|
||||
}
|
||||
if ((unsigned int)_nPins < _numInputs + _numOutputs)
|
||||
DIAG(F("CMRInode: bus:%d address:%d WARNING number of Vpins does not cover all inputs and outputs"), _busNo, _address);
|
||||
|
||||
// Allocate memory for states
|
||||
_inputStates = (uint8_t *)calloc((_numInputs+7)/8, 1);
|
||||
_outputStates = (uint8_t *)calloc((_numOutputs+7)/8, 1);
|
||||
if (!_inputStates || !_outputStates) {
|
||||
DIAG(F("CMRInode: ERROR insufficient memory"));
|
||||
return;
|
||||
}
|
||||
|
||||
// Add this device to HAL device list
|
||||
IODevice::addDevice(this);
|
||||
|
||||
// Add CMRInode to CMRIbus object.
|
||||
CMRIbus *bus = CMRIbus::findBus(_busNo);
|
||||
if (bus != NULL) {
|
||||
bus->addNode(this);
|
||||
return;
|
||||
}
|
||||
}
|
||||
|
||||
293
IO_CMRI.h
Normal file
293
IO_CMRI.h
Normal file
|
|
@ -0,0 +1,293 @@
|
|||
/*
|
||||
* © 2023, Neil McKechnie. All rights reserved.
|
||||
*
|
||||
* This file is part of DCC++EX API
|
||||
*
|
||||
* This is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* It is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with CommandStation. If not, see <https://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
/*
|
||||
* CMRIbus
|
||||
* =======
|
||||
* To define a CMRI bus, example syntax:
|
||||
* CMRIbus::create(bus, serial, baud[, cycletime[, pin]]);
|
||||
*
|
||||
* bus = 0-255
|
||||
* serial = serial port to be used (e.g. Serial3)
|
||||
* baud = baud rate (9600, 19200, 28800, 57600 or 115200)
|
||||
* cycletime = minimum time between successive updates/reads of a node in millisecs (default 500ms)
|
||||
* pin = pin number connected to RS485 module's DE and !RE terminals for half-duplex operation (default VPIN_NONE)
|
||||
*
|
||||
* Each bus must use a different serial port.
|
||||
*
|
||||
* IMPORTANT: If you are using ArduinoCMRI library code by Michael Adams, at the time of writing this library
|
||||
* is not compliant with the LCS-9.10.1 specification for CMRInet protocol.
|
||||
* Various work-arounds may be enabled within the driver by adding the following line to your config.h file,
|
||||
* to allow nodes running the ArduinoCMRI library to communicate:
|
||||
*
|
||||
* #define ARDUINOCMRI_COMPATIBLE
|
||||
*
|
||||
* CMRINode
|
||||
* ========
|
||||
* To define a CMRI node and associate it with a CMRI bus,
|
||||
* CMRInode::create(firstVPIN, numVPINs, bus, address, type [, inputs, outputs]);
|
||||
*
|
||||
* firstVPIN = first vpin in block allocated to this device
|
||||
* numVPINs = number of vpins (e.g. 72 for an SMINI node)
|
||||
* bus = 0-255
|
||||
* address = 0-127
|
||||
* type = 'M' for SMINI (fixed 24 inputs and 48 outputs)
|
||||
* 'C' for CPNODE (16 to 144 inputs/outputs in groups of 8)
|
||||
* (other types are not supported at this time).
|
||||
* inputs = number of inputs (CPNODE only)
|
||||
* outputs = number of outputs (CPNODE only)
|
||||
*
|
||||
* Reference: "LCS-9.10.1
|
||||
* Layout Control Specification: CMRInet Protocol
|
||||
* Version 1.1 December 2014."
|
||||
*/
|
||||
|
||||
#ifndef IO_CMRI_H
|
||||
#define IO_CMRI_H
|
||||
|
||||
#include "IODevice.h"
|
||||
|
||||
/**********************************************************************
|
||||
* CMRInode class
|
||||
*
|
||||
* This encapsulates the state associated with a single CMRI node,
|
||||
* which includes the address type, number of inputs and outputs, and
|
||||
* the states of the inputs and outputs.
|
||||
**********************************************************************/
|
||||
class CMRInode : public IODevice {
|
||||
private:
|
||||
uint8_t _busNo;
|
||||
uint8_t _address;
|
||||
char _type;
|
||||
CMRInode *_next = NULL;
|
||||
uint8_t *_inputStates = NULL;
|
||||
uint8_t *_outputStates = NULL;
|
||||
uint16_t _numInputs = 0;
|
||||
uint16_t _numOutputs = 0;
|
||||
bool _initialised = false;
|
||||
|
||||
public:
|
||||
static void create(VPIN firstVpin, int nPins, uint8_t busNo, uint8_t address, char type, uint16_t inputs=0, uint16_t outputs=0) {
|
||||
if (checkNoOverlap(firstVpin, nPins)) new CMRInode(firstVpin, nPins, busNo, address, type, inputs, outputs);
|
||||
}
|
||||
CMRInode(VPIN firstVpin, int nPins, uint8_t busNo, uint8_t address, char type, uint16_t inputs=0, uint16_t outputs=0);
|
||||
|
||||
uint8_t getAddress() {
|
||||
return _address;
|
||||
}
|
||||
CMRInode *getNext() {
|
||||
return _next;
|
||||
}
|
||||
void setNext(CMRInode *node) {
|
||||
_next = node;
|
||||
}
|
||||
bool isInitialised() {
|
||||
return _initialised;
|
||||
}
|
||||
void setInitialised() {
|
||||
_initialised = true;
|
||||
}
|
||||
|
||||
void _begin() {
|
||||
_initialised = false;
|
||||
}
|
||||
|
||||
int _read(VPIN vpin) {
|
||||
// Return current state from this device
|
||||
uint16_t pin = vpin - _firstVpin;
|
||||
if (pin < _numInputs) {
|
||||
uint8_t mask = 1 << (pin & 0x7);
|
||||
int index = pin / 8;
|
||||
return (_inputStates[index] & mask) != 0;
|
||||
} else
|
||||
return 0;
|
||||
}
|
||||
|
||||
void _write(VPIN vpin, int value) {
|
||||
// Update current state for this device, in preparation the bus transmission
|
||||
uint16_t pin = vpin - _firstVpin - _numInputs;
|
||||
if (pin < _numOutputs) {
|
||||
uint8_t mask = 1 << (pin & 0x7);
|
||||
int index = pin / 8;
|
||||
if (value)
|
||||
_outputStates[index] |= mask;
|
||||
else
|
||||
_outputStates[index] &= ~mask;
|
||||
}
|
||||
}
|
||||
|
||||
void saveIncomingData(uint8_t index, uint8_t data) {
|
||||
if (index < (_numInputs+7)/8)
|
||||
_inputStates[index] = data;
|
||||
}
|
||||
|
||||
uint8_t getOutputStates(uint8_t index) {
|
||||
if (index < (_numOutputs+7)/8)
|
||||
return _outputStates[index];
|
||||
else
|
||||
return 0;
|
||||
}
|
||||
|
||||
uint16_t getNumInputs() {
|
||||
return _numInputs;
|
||||
}
|
||||
|
||||
uint16_t getNumOutputs() {
|
||||
return _numOutputs;
|
||||
}
|
||||
|
||||
char getType() {
|
||||
return _type;
|
||||
}
|
||||
|
||||
uint8_t getBusNumber() {
|
||||
return _busNo;
|
||||
}
|
||||
|
||||
void _display() override {
|
||||
DIAG(F("CMRInode type:'%c' configured on bus:%d address:%d VPINs:%u-%u (in) %u-%u (out)"),
|
||||
_type, _busNo, _address, _firstVpin, _firstVpin+_numInputs-1,
|
||||
_firstVpin+_numInputs, _firstVpin+_numInputs+_numOutputs-1);
|
||||
}
|
||||
|
||||
};
|
||||
|
||||
/**********************************************************************
|
||||
* CMRIbus class
|
||||
*
|
||||
* This encapsulates the properties state of the bus and the
|
||||
* transmission and reception of data across that bus. Each CMRIbus
|
||||
* object owns a set of CMRInode objects which represent the nodes
|
||||
* attached to that bus.
|
||||
**********************************************************************/
|
||||
class CMRIbus : public IODevice {
|
||||
private:
|
||||
// Here we define the device-specific variables.
|
||||
uint8_t _busNo;
|
||||
HardwareSerial *_serial;
|
||||
unsigned long _baud;
|
||||
VPIN _transmitEnablePin = VPIN_NONE;
|
||||
CMRInode *_nodeListStart = NULL, *_nodeListEnd = NULL;
|
||||
CMRInode *_currentNode = NULL;
|
||||
|
||||
// Transmitter state machine states
|
||||
enum {TD_IDLE, TD_PRETRANSMIT, TD_INIT, TD_TRANSMIT, TD_PROMPT, TD_RECEIVE};
|
||||
uint8_t _transmitState = TD_IDLE;
|
||||
// Receiver state machine states.
|
||||
enum {RD_SYN1, RD_SYN2, RD_STX, RD_ADDR, RD_TYPE,
|
||||
RD_DATA, RD_ESCDATA, RD_SKIPDATA, RD_SKIPESCDATA, RD_ETX};
|
||||
uint8_t _receiveState = RD_SYN1;
|
||||
uint16_t _receiveDataIndex = 0; // Index of next data byte to be received.
|
||||
CMRIbus *_nextBus = NULL; // Pointer to next bus instance in list.
|
||||
unsigned long _cycleStartTime = 0;
|
||||
unsigned long _timeoutStart = 0;
|
||||
unsigned long _cycleTime; // target time between successive read/write cycles, microseconds
|
||||
unsigned long _timeoutPeriod; // timeout on read responses, in microseconds.
|
||||
unsigned long _currentMicros; // last value of micros() from _loop function.
|
||||
unsigned long _postDelay; // delay time after transmission before switching off transmitter (in us)
|
||||
unsigned long _byteTransmitTime; // time in us for transmission of one byte
|
||||
|
||||
static CMRIbus *_busList; // linked list of defined bus instances
|
||||
|
||||
// Definition of special characters in CMRInet protocol
|
||||
enum : uint8_t {
|
||||
NUL = 0x00,
|
||||
STX = 0x02,
|
||||
ETX = 0x03,
|
||||
DLE = 0x10,
|
||||
SYN = 0xff,
|
||||
};
|
||||
|
||||
public:
|
||||
static void create(uint8_t busNo, HardwareSerial &serial, unsigned long baud, uint16_t cycleTimeMS=500, VPIN transmitEnablePin=VPIN_NONE) {
|
||||
new CMRIbus(busNo, serial, baud, cycleTimeMS, transmitEnablePin);
|
||||
}
|
||||
|
||||
// Device-specific initialisation
|
||||
void _begin() override {
|
||||
// CMRInet spec states one stop bit, JMRI and ArduinoCMRI use two stop bits
|
||||
#if defined(ARDUINOCMRI_COMPATIBLE)
|
||||
_serial->begin(_baud, SERIAL_8N2);
|
||||
#else
|
||||
_serial->begin(_baud, SERIAL_8N1);
|
||||
#endif
|
||||
#if defined(DIAG_IO)
|
||||
_display();
|
||||
#endif
|
||||
}
|
||||
|
||||
// Loop function (overriding IODevice::_loop(unsigned long))
|
||||
void _loop(unsigned long currentMicros) override;
|
||||
|
||||
// Display information about the device
|
||||
void _display() override {
|
||||
DIAG(F("CMRIbus %d configured, speed=%d baud, cycle=%d ms"), _busNo, _baud, _cycleTime/1000);
|
||||
}
|
||||
|
||||
// Locate CMRInode object with specified address.
|
||||
CMRInode *findNode(uint8_t address) {
|
||||
for (CMRInode *node = _nodeListStart; node != NULL; node = node->getNext()) {
|
||||
if (node->getAddress() == address)
|
||||
return node;
|
||||
}
|
||||
return NULL;
|
||||
}
|
||||
|
||||
// Add new CMRInode to the list of nodes for this bus.
|
||||
void addNode(CMRInode *newNode) {
|
||||
if (!_nodeListStart)
|
||||
_nodeListStart = newNode;
|
||||
if (!_nodeListEnd)
|
||||
_nodeListEnd = newNode;
|
||||
else {
|
||||
_nodeListEnd->setNext(newNode);
|
||||
_nodeListEnd = newNode;
|
||||
}
|
||||
}
|
||||
|
||||
protected:
|
||||
CMRIbus(uint8_t busNo, HardwareSerial &serial, unsigned long baud, uint16_t cycleTimeMS, VPIN transmitEnablePin);
|
||||
uint16_t sendData(CMRInode *node);
|
||||
uint16_t requestData(CMRInode *node);
|
||||
uint16_t sendInitialisation(CMRInode *node);
|
||||
|
||||
// Process any data bytes received from a CMRInode.
|
||||
void processIncoming();
|
||||
// Process any outgoing traffic that is due.
|
||||
void processOutgoing();
|
||||
// Enable transmitter
|
||||
void enableTransmitter();
|
||||
// Disable transmitter and enable receiver
|
||||
void disableTransmitter();
|
||||
|
||||
|
||||
public:
|
||||
uint8_t getBusNumber() {
|
||||
return _busNo;
|
||||
}
|
||||
|
||||
static CMRIbus *findBus(uint8_t busNo) {
|
||||
for (CMRIbus *bus=_busList; bus!=NULL; bus=bus->_nextBus) {
|
||||
if (bus->_busNo == busNo) return bus;
|
||||
}
|
||||
return NULL;
|
||||
}
|
||||
};
|
||||
|
||||
#endif // IO_CMRI_H
|
||||
794
IO_I2CDFPlayer.h
Normal file
794
IO_I2CDFPlayer.h
Normal file
|
|
@ -0,0 +1,794 @@
|
|||
/*
|
||||
* © 2023, Neil McKechnie. All rights reserved.
|
||||
*
|
||||
* This file is part of DCC++EX API
|
||||
*
|
||||
* This is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* It is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with CommandStation. If not, see <https://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
/*
|
||||
* DFPlayer is an MP3 player module with an SD card holder. It also has an integrated
|
||||
* amplifier, so it only needs a power supply and a speaker.
|
||||
* This driver is a modified version of the IO_DFPlayer.h file
|
||||
* *********************************************************************************************
|
||||
*
|
||||
* 2023, Added NXP SC16IS752 I2C Dual UART to enable the DFPlayer connection over the I2C bus
|
||||
* The SC16IS752 has 64 bytes TX & RX FIFO buffer
|
||||
* First version without interrupts from I2C UART and only RX/TX are used, interrupts may not be
|
||||
* needed as the RX Fifo holds the reply
|
||||
*
|
||||
* myHall.cpp configuration syntax:
|
||||
*
|
||||
* I2CDFPlayer::create(1st vPin, vPins, I2C address, UART ch, AM);
|
||||
*
|
||||
* Parameters:
|
||||
* 1st vPin : First virtual pin that EX-Rail can control to play a sound, use PLAYSOUND command (alias of ANOUT)
|
||||
* vPins : Total number of virtual pins allocated (only 1 vPin is supported)
|
||||
* I2C Address : I2C address of the serial controller, in 0x format,
|
||||
* UART ch : Indicating UART 0 or UART 1, values 0 or 1
|
||||
* AM : audio mixer, values: 1 or 2 to select an audio amplifier, no effect if AM is not installed
|
||||
*
|
||||
* The vPin is also an pin that can be read, it indicated if the DFPlayer has finished playing a track
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef IO_I2CDFPlayer_h
|
||||
#define IO_I2CDFPlayer_h
|
||||
|
||||
#include "IODevice.h"
|
||||
#include "I2CManager.h"
|
||||
#include "DIAG.h"
|
||||
|
||||
// Debug and diagnostic defines, enable too many will result in slowing the driver
|
||||
//#define DIAG_I2CDFplayer
|
||||
//#define DIAG_I2CDFplayer_data
|
||||
//#define DIAG_I2CDFplayer_reg
|
||||
//#define DIAG_I2CDFplayer_playing
|
||||
|
||||
class I2CDFPlayer : public IODevice {
|
||||
private:
|
||||
const uint8_t MAXVOLUME=30;
|
||||
uint8_t RETRYCOUNT = 0x03;
|
||||
bool _playing = false;
|
||||
uint8_t _inputIndex = 0;
|
||||
unsigned long _commandSendTime; // Time (us) that last transmit took place.
|
||||
unsigned long _timeoutTime;
|
||||
uint8_t _recvCMD; // Last received command code byte
|
||||
bool _awaitingResponse = false;
|
||||
uint8_t _retryCounter = RETRYCOUNT; // Max retries before timing out
|
||||
uint8_t _requestedVolumeLevel = MAXVOLUME;
|
||||
uint8_t _currentVolume = MAXVOLUME;
|
||||
int _requestedSong = -1; // -1=none, 0=stop, >0=file number
|
||||
bool _repeat = false; // audio file is repeat playing
|
||||
uint8_t _previousCmd = true;
|
||||
// SC16IS752 defines
|
||||
I2CAddress _I2CAddress;
|
||||
I2CRB _rb;
|
||||
uint8_t _UART_CH;
|
||||
// Communication parameters for the DFPlayer are fixed at 8 bit, No parity, 1 stopbit
|
||||
uint8_t WORD_LEN = 0x03; // Value LCR bit 0,1
|
||||
uint8_t STOP_BIT = 0x00; // Value LCR bit 2
|
||||
uint8_t PARITY_ENA = 0x00; // Value LCR bit 3
|
||||
uint8_t PARITY_TYPE = 0x00; // Value LCR bit 4
|
||||
uint32_t BAUD_RATE = 9600;
|
||||
uint8_t PRESCALER = 0x01; // Value MCR bit 7
|
||||
uint8_t TEMP_REG_VAL = 0x00;
|
||||
uint8_t FIFO_RX_LEVEL = 0x00;
|
||||
uint8_t RX_BUFFER = 0x00; // nr of bytes copied into _inbuffer
|
||||
uint8_t FIFO_TX_LEVEL = 0x00;
|
||||
bool _playCmd = false;
|
||||
bool _volCmd = false;
|
||||
bool _folderCmd = false;
|
||||
uint8_t _requestedFolder = 0x01; // default to folder 01
|
||||
uint8_t _currentFolder = 0x01; // default to folder 01
|
||||
bool _repeatCmd = false;
|
||||
bool _stopplayCmd = false;
|
||||
bool _resetCmd = false;
|
||||
bool _eqCmd = false;
|
||||
uint8_t _requestedEQValue = NORMAL;
|
||||
uint8_t _currentEQvalue = NORMAL; // start equalizer value
|
||||
bool _daconCmd = false;
|
||||
uint8_t _audioMixer = 0x01; // Default to output amplifier 1
|
||||
bool _setamCmd = false; // Set the Audio mixer channel
|
||||
uint8_t _outbuffer [11]; // DFPlayer command is 10 bytes + 1 byte register address & UART channel
|
||||
uint8_t _inbuffer[10]; // expected DFPlayer return 10 bytes
|
||||
|
||||
//unsigned long SC16IS752_XTAL_FREQ = 1843200; // To support cheap eBay/AliExpress SC16IS752 boards
|
||||
unsigned long SC16IS752_XTAL_FREQ = 14745600; // Support for higher baud rates, standard for modular EX-IO system
|
||||
|
||||
|
||||
public:
|
||||
// Constructor
|
||||
I2CDFPlayer(VPIN firstVpin, int nPins, I2CAddress i2cAddress, uint8_t UART_CH, uint8_t AM){
|
||||
_firstVpin = firstVpin;
|
||||
_nPins = nPins;
|
||||
_I2CAddress = i2cAddress;
|
||||
_UART_CH = UART_CH;
|
||||
_audioMixer = AM;
|
||||
addDevice(this);
|
||||
}
|
||||
|
||||
public:
|
||||
static void create(VPIN firstVpin, int nPins, I2CAddress i2cAddress, uint8_t UART_CH, uint8_t AM) {
|
||||
if (checkNoOverlap(firstVpin, nPins, i2cAddress)) new I2CDFPlayer(firstVpin, nPins, i2cAddress, UART_CH, AM);
|
||||
}
|
||||
|
||||
void _begin() override {
|
||||
// check if SC16IS752 exist first, initialize and then resume DFPlayer init via SC16IS752
|
||||
I2CManager.begin();
|
||||
I2CManager.setClock(1000000);
|
||||
if (I2CManager.exists(_I2CAddress)){
|
||||
DIAG(F("SC16IS752 I2C:%s UART detected"), _I2CAddress.toString());
|
||||
Init_SC16IS752(); // Initialize UART
|
||||
if (_deviceState == DEVSTATE_FAILED){
|
||||
DIAG(F("SC16IS752 I2C:%s UART initialization failed"), _I2CAddress.toString());
|
||||
}
|
||||
} else {
|
||||
DIAG(F("SC16IS752 I2C:%s UART not detected"), _I2CAddress.toString());
|
||||
}
|
||||
#if defined(DIAG_IO)
|
||||
_display();
|
||||
#endif
|
||||
// Now init DFPlayer
|
||||
// Send a query to the device to see if it responds
|
||||
_deviceState = DEVSTATE_INITIALISING;
|
||||
sendPacket(0x42,0,0);
|
||||
_timeoutTime = micros() + 5000000UL; // 5 second timeout
|
||||
_awaitingResponse = true;
|
||||
}
|
||||
|
||||
|
||||
void _loop(unsigned long currentMicros) override {
|
||||
// Read responses from device
|
||||
uint8_t status = _rb.status;
|
||||
if (status == I2C_STATUS_PENDING) return; // Busy, so don't do anything
|
||||
if (status == I2C_STATUS_OK) {
|
||||
processIncoming(currentMicros);
|
||||
// Check if a command sent to device has timed out. Allow 0.5 second for response
|
||||
// added retry counter, sometimes we do not sent keep alive due to other commands sent to DFPlayer
|
||||
if (_awaitingResponse && (int32_t)(currentMicros - _timeoutTime) > 0) { // timeout triggered
|
||||
if(_retryCounter == 0){ // retry counter out of luck, must take the device to failed state
|
||||
DIAG(F("I2CDFPlayer:%s, DFPlayer not responding on UART channel: 0x%x"), _I2CAddress.toString(), _UART_CH);
|
||||
_deviceState = DEVSTATE_FAILED;
|
||||
_awaitingResponse = false;
|
||||
_playing = false;
|
||||
_retryCounter = RETRYCOUNT;
|
||||
} else { // timeout and retry protection and recovery of corrupt data frames from DFPlayer
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: %s, DFPlayer timout, retry counter: %d on UART channel: 0x%x"), _I2CAddress.toString(), _retryCounter, _UART_CH);
|
||||
#endif
|
||||
_timeoutTime = currentMicros + 5000000UL; // Timeout if no response within 5 seconds// reset timeout
|
||||
_awaitingResponse = false; // trigger sending a keep alive 0x42 in processOutgoing()
|
||||
_retryCounter --; // decrement retry counter
|
||||
resetRX_fifo(); // reset the RX fifo as it has corrupt data
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
status = _rb.status;
|
||||
if (status == I2C_STATUS_PENDING) return; // Busy, try next time
|
||||
if (status == I2C_STATUS_OK) {
|
||||
// Send any commands that need to go.
|
||||
processOutgoing(currentMicros);
|
||||
}
|
||||
delayUntil(currentMicros + 10000); // Only enter every 10ms
|
||||
}
|
||||
|
||||
|
||||
// Check for incoming data, and update busy flag and other state accordingly
|
||||
|
||||
void processIncoming(unsigned long currentMicros) {
|
||||
// Expected message is in the form "7E FF 06 3D xx xx xx xx xx EF"
|
||||
RX_fifo_lvl();
|
||||
if (FIFO_RX_LEVEL >= 10) {
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
DIAG(F("I2CDFPlayer: %s Retrieving data from RX Fifo on UART_CH: 0x%x FIFO_RX_LEVEL: %d"),_I2CAddress.toString(), _UART_CH, FIFO_RX_LEVEL);
|
||||
#endif
|
||||
_outbuffer[0] = REG_RHR << 3 | _UART_CH << 1;
|
||||
// Only copy 10 bytes from RX FIFO, there maybe additional partial return data after a track is finished playing in the RX FIFO
|
||||
I2CManager.read(_I2CAddress, _inbuffer, 10, _outbuffer, 1); // inbuffer[] has the data now
|
||||
//delayUntil(currentMicros + 10000); // Allow time to get the data
|
||||
RX_BUFFER = 10; // We have copied 10 bytes from RX FIFO to _inbuffer
|
||||
#ifdef DIAG_I2CDFplayer_data
|
||||
DIAG(F("SC16IS752: At I2C: %s, UART channel: 0x%x, RX FIFO Data"), _I2CAddress.toString(), _UART_CH);
|
||||
for (int i = 0; i < sizeof _inbuffer; i++){
|
||||
DIAG(F("SC16IS752: Data _inbuffer[0x%x]: 0x%x"), i, _inbuffer[i]);
|
||||
}
|
||||
#endif
|
||||
} else {
|
||||
FIFO_RX_LEVEL = 0; //set to 0, we'll read a fresh FIFO_RX_LEVEL next time
|
||||
return; // No data or not enough data in rx fifo, check again next time around
|
||||
}
|
||||
|
||||
|
||||
bool ok = false;
|
||||
//DIAG(F("I2CDFPlayer: RX_BUFFER: %d"), RX_BUFFER);
|
||||
while (RX_BUFFER != 0) {
|
||||
int c = _inbuffer[_inputIndex]; // Start at 0, increment to FIFO_RX_LEVEL
|
||||
switch (_inputIndex) {
|
||||
case 0:
|
||||
if (c == 0x7E) ok = true;
|
||||
break;
|
||||
case 1:
|
||||
if (c == 0xFF) ok = true;
|
||||
break;
|
||||
case 2:
|
||||
if (c== 0x06) ok = true;
|
||||
break;
|
||||
case 3:
|
||||
_recvCMD = c; // CMD byte
|
||||
ok = true;
|
||||
break;
|
||||
case 6:
|
||||
switch (_recvCMD) {
|
||||
//DIAG(F("I2CDFPlayer: %s, _recvCMD: 0x%x _awaitingResponse: 0x0%x"),_I2CAddress.toString(), _recvCMD, _awaitingResponse);
|
||||
case 0x42:
|
||||
// Response to status query
|
||||
_playing = (c != 0);
|
||||
// Mark the device online and cancel timeout
|
||||
if (_deviceState==DEVSTATE_INITIALISING) {
|
||||
_deviceState = DEVSTATE_NORMAL;
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
DIAG(F("I2CDFPlayer: %s, UART_CH: 0x0%x, _deviceState: 0x0%x"),_I2CAddress.toString(), _UART_CH, _deviceState);
|
||||
#endif
|
||||
#ifdef DIAG_IO
|
||||
_display();
|
||||
#endif
|
||||
}
|
||||
_awaitingResponse = false;
|
||||
break;
|
||||
case 0x3d:
|
||||
// End of play
|
||||
if (_playing) {
|
||||
#ifdef DIAG_IO
|
||||
DIAG(F("I2CDFPlayer: Finished"));
|
||||
#endif
|
||||
_playing = false;
|
||||
}
|
||||
break;
|
||||
case 0x40:
|
||||
// Error codes; 1: Module Busy
|
||||
DIAG(F("I2CDFPlayer: Error %d returned from device"), c);
|
||||
_playing = false;
|
||||
break;
|
||||
}
|
||||
ok = true;
|
||||
break;
|
||||
case 4: case 5: case 7: case 8:
|
||||
ok = true; // Skip over these bytes in message.
|
||||
break;
|
||||
case 9:
|
||||
if (c==0xef) {
|
||||
// Message finished
|
||||
_retryCounter = RETRYCOUNT; // reset the retry counter as we have received a valid packet
|
||||
}
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
if (ok){
|
||||
_inputIndex++; // character as expected, so increment index
|
||||
RX_BUFFER --; // Decrease FIFO_RX_LEVEL with each character read from _inbuffer[_inputIndex]
|
||||
} else {
|
||||
_inputIndex = 0; // otherwise reset.
|
||||
RX_BUFFER = 0;
|
||||
}
|
||||
}
|
||||
RX_BUFFER = 0; //Set to 0, we'll read a new RX FIFO level again
|
||||
}
|
||||
|
||||
|
||||
// Send any commands that need to be sent
|
||||
void processOutgoing(unsigned long currentMicros) {
|
||||
// When two commands are sent in quick succession, the device will often fail to
|
||||
// execute one. Testing has indicated that a delay of 100ms or more is required
|
||||
// between successive commands to get reliable operation.
|
||||
// If 100ms has elapsed since the last thing sent, then check if there's some output to do.
|
||||
if (((int32_t)currentMicros - _commandSendTime) > 100000) {
|
||||
if ( _resetCmd == true){
|
||||
sendPacket(0x0C,0,0);
|
||||
_resetCmd = false;
|
||||
} else if(_volCmd == true) { // do the volme before palying a track
|
||||
if(_requestedVolumeLevel >= 0 && _requestedVolumeLevel <= 30){
|
||||
_currentVolume = _requestedVolumeLevel; // If _requestedVolumeLevel is out of range, sent _currentV1olume
|
||||
}
|
||||
sendPacket(0x06, 0x00, _currentVolume);
|
||||
_volCmd = false;
|
||||
} else if (_playCmd == true) {
|
||||
// Change song
|
||||
if (_requestedSong != -1) {
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: _requestedVolumeLevel: %u, _requestedSong: %u, _currentFolder: %u _playCmd: 0x%x"), _requestedVolumeLevel, _requestedSong, _currentFolder, _playCmd);
|
||||
#endif
|
||||
sendPacket(0x0F, _currentFolder, _requestedSong); // audio file in folder
|
||||
_requestedSong = -1;
|
||||
_playCmd = false;
|
||||
}
|
||||
} //else if (_requestedSong == 0) {
|
||||
else if (_stopplayCmd == true) {
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: Stop playing: _stopplayCmd: 0x%x"), _stopplayCmd);
|
||||
#endif
|
||||
sendPacket(0x16, 0x00, 0x00); // Stop playing
|
||||
_requestedSong = -1;
|
||||
_repeat = false; // reset repeat
|
||||
_stopplayCmd = false;
|
||||
} else if (_folderCmd == true) {
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: Folder: _folderCmd: 0x%x, _requestedFolder: %d"), _stopplayCmd, _requestedFolder);
|
||||
#endif
|
||||
if (_currentFolder != _requestedFolder){
|
||||
_currentFolder = _requestedFolder;
|
||||
}
|
||||
_folderCmd = false;
|
||||
} else if (_repeatCmd == true) {
|
||||
if(_repeat == false) { // No repeat play currently
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: Repeat: _repeatCmd: 0x%x, _requestedSong: %d, _repeat: 0x0%x"), _repeatCmd, _requestedSong, _repeat);
|
||||
#endif
|
||||
sendPacket(0x08, 0x00, _requestedSong); // repeat playing audio file in root folder
|
||||
_requestedSong = -1;
|
||||
_repeat = true;
|
||||
}
|
||||
_repeatCmd= false;
|
||||
} else if (_daconCmd == true) { // Always turn DAC on
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: DACON: _daconCmd: 0x%x"), _daconCmd);
|
||||
#endif
|
||||
sendPacket(0x1A,0,0x00);
|
||||
_daconCmd = false;
|
||||
} else if (_eqCmd == true){ // Set Equalizer, values 0x00 - 0x05
|
||||
if (_currentEQvalue != _requestedEQValue){
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: EQ: _eqCmd: 0x%x, _currentEQvalue: 0x0%x, _requestedEQValue: 0x0%x"), _eqCmd, _currentEQvalue, _requestedEQValue);
|
||||
#endif
|
||||
_currentEQvalue = _requestedEQValue;
|
||||
sendPacket(0x07,0x00,_currentEQvalue);
|
||||
}
|
||||
_eqCmd = false;
|
||||
} else if (_setamCmd == true){ // Set Audio mixer channel
|
||||
setGPIO(); // Set the audio mixer channel
|
||||
/*
|
||||
if (_audioMixer == 1){ // set to audio mixer 1
|
||||
if (_UART_CH == 0){
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 0 to high
|
||||
} else { // must be UART 1
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 1 to high
|
||||
}
|
||||
//_setamCmd = false;
|
||||
//UART_WriteRegister(REG_IOSTATE, TEMP_REG_VAL);
|
||||
} else { // set to audio mixer 2
|
||||
if (_UART_CH == 0){
|
||||
TEMP_REG_VAL &= (0x00 << _UART_CH); //Set GPIO pin 0 to Low
|
||||
} else { // must be UART 1
|
||||
TEMP_REG_VAL &= (0x00 << _UART_CH); //Set GPIO pin 1 to Low
|
||||
}
|
||||
//_setamCmd = false;
|
||||
//UART_WriteRegister(REG_IOSTATE, TEMP_REG_VAL);
|
||||
}*/
|
||||
_setamCmd = false;
|
||||
} else if ((int32_t)currentMicros - _commandSendTime > 1000000) {
|
||||
// Poll device every second that other commands aren't being sent,
|
||||
// to check if it's still connected and responding.
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: Send keepalive") );
|
||||
#endif
|
||||
sendPacket(0x42,0,0);
|
||||
if (!_awaitingResponse) {
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: Send keepalive, _awaitingResponse: 0x0%x"), _awaitingResponse );
|
||||
#endif
|
||||
_timeoutTime = currentMicros + 5000000UL; // Timeout if no response within 5 seconds
|
||||
_awaitingResponse = true;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
// Write to a vPin will do nothing
|
||||
void _write(VPIN vpin, int value) override {
|
||||
if (_deviceState == DEVSTATE_FAILED) return;
|
||||
#ifdef DIAG_IO
|
||||
DIAG(F("I2CDFPlayer: Writing to any vPin not supported"));
|
||||
#endif
|
||||
}
|
||||
|
||||
|
||||
// WriteAnalogue on first pin uses the nominated value as a file number to start playing, if file number > 0.
|
||||
// Volume may be specified as second parameter to writeAnalogue.
|
||||
// If value is zero, the player stops playing.
|
||||
// WriteAnalogue on second pin sets the output volume.
|
||||
//
|
||||
// WriteAnalogue to be done on first vpin
|
||||
//
|
||||
//void _writeAnalogue(VPIN vpin, int value, uint8_t volume=0, uint16_t=0) override {
|
||||
void _writeAnalogue(VPIN vpin, int value, uint8_t volume=0, uint16_t cmd=0) override {
|
||||
if (_deviceState == DEVSTATE_FAILED) return;
|
||||
#ifdef DIAG_IO
|
||||
DIAG(F("I2CDFPlayer: VPIN:%u FileNo:%d Volume:%d Command:0x%x"), vpin, value, volume, cmd);
|
||||
#endif
|
||||
uint8_t pin = vpin - _firstVpin;
|
||||
if (pin == 0) { // Enhanced DFPlayer commands, do nothing if not vPin 0
|
||||
// Read command and value
|
||||
switch (cmd){
|
||||
//case NONE:
|
||||
// DFPlayerCmd = cmd;
|
||||
// break;
|
||||
case PLAY:
|
||||
_playCmd = true;
|
||||
_volCmd = true;
|
||||
_requestedSong = value;
|
||||
_requestedVolumeLevel = volume;
|
||||
_playing = true;
|
||||
break;
|
||||
case VOL:
|
||||
_volCmd = true;
|
||||
_requestedVolumeLevel = volume;
|
||||
break;
|
||||
case FOLDER:
|
||||
_folderCmd = true;
|
||||
if (volume <= 0 || volume > 99){ // Range checking, valid values 1-99, else default to 1
|
||||
_requestedFolder = 0x01; // if outside range, default to folder 01
|
||||
} else {
|
||||
_requestedFolder = volume;
|
||||
}
|
||||
break;
|
||||
case REPEATPLAY: // Need to check if _repeat == true, if so do nothing
|
||||
if (_repeat == false) {
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: WriteAnalog Repeat: _repeat: 0x0%x, value: %d _repeatCmd: 0x%x"), _repeat, value, _repeatCmd);
|
||||
#endif
|
||||
_repeatCmd = true;
|
||||
_requestedSong = value;
|
||||
_requestedVolumeLevel = volume;
|
||||
_playing = true;
|
||||
}
|
||||
break;
|
||||
case STOPPLAY:
|
||||
_stopplayCmd = true;
|
||||
break;
|
||||
case EQ:
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: WriteAnalog EQ: cmd: 0x%x, EQ value: 0x%x"), cmd, volume);
|
||||
#endif
|
||||
_eqCmd = true;
|
||||
if (volume <= 0 || volume > 5) { // If out of range, default to NORMAL
|
||||
_requestedEQValue = NORMAL;
|
||||
} else { // Valid EQ parameter range
|
||||
_requestedEQValue = volume;
|
||||
}
|
||||
break;
|
||||
case RESET:
|
||||
_resetCmd = true;
|
||||
break;
|
||||
case DACON: // Works, but without the DACOFF command limited value, except when not relying on DFPlayer default to turn the DAC on
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: WrtieAnalog DACON: cmd: 0x%x"), cmd);
|
||||
#endif
|
||||
_daconCmd = true;
|
||||
break;
|
||||
case SETAM: // Set the audio mixer channel to 1 or 2
|
||||
_setamCmd = true;
|
||||
#ifdef DIAG_I2CDFplayer_playing
|
||||
DIAG(F("I2CDFPlayer: WrtieAnalog SETAM: cmd: 0x%x"), cmd);
|
||||
#endif
|
||||
if (volume <= 0 || volume > 2) { // If out of range, default to 1
|
||||
_audioMixer = 1;
|
||||
} else { // Valid SETAM parameter in range
|
||||
_audioMixer = volume; // _audioMixer valid values 1 or 2
|
||||
}
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
// A read on any pin indicates if the player is still playing.
|
||||
int _read(VPIN vpin) override {
|
||||
if (_deviceState == DEVSTATE_FAILED) return false;
|
||||
uint8_t pin = vpin - _firstVpin;
|
||||
if (pin == 0) { // Do nothing if not vPin 0
|
||||
return _playing;
|
||||
}
|
||||
}
|
||||
|
||||
void _display() override {
|
||||
DIAG(F("I2CDFPlayer Configured on Vpins:%u-%u %S"), _firstVpin, _firstVpin+_nPins-1,
|
||||
(_deviceState==DEVSTATE_FAILED) ? F("OFFLINE") : F(""));
|
||||
}
|
||||
|
||||
private:
|
||||
// DFPlayer command frame
|
||||
// 7E FF 06 0F 00 01 01 xx xx EF
|
||||
// 0 -> 7E is start code
|
||||
// 1 -> FF is version
|
||||
// 2 -> 06 is length
|
||||
// 3 -> 0F is command
|
||||
// 4 -> 00 is no receive
|
||||
// 5~6 -> 01 01 is argument
|
||||
// 7~8 -> checksum = 0 - ( FF+06+0F+00+01+01 )
|
||||
// 9 -> EF is end code
|
||||
|
||||
void sendPacket(uint8_t command, uint8_t arg1 = 0, uint8_t arg2 = 0) {
|
||||
FIFO_TX_LEVEL = 0; // Reset FIFO_TX_LEVEL
|
||||
uint8_t out[] = {
|
||||
0x7E,
|
||||
0xFF,
|
||||
06,
|
||||
command,
|
||||
00,
|
||||
//static_cast<uint8_t>(arg >> 8),
|
||||
//static_cast<uint8_t>(arg & 0x00ff),
|
||||
arg1,
|
||||
arg2,
|
||||
00,
|
||||
00,
|
||||
0xEF };
|
||||
|
||||
setChecksum(out);
|
||||
|
||||
// Prepend the DFPlayer command with REG address and UART Channel in _outbuffer
|
||||
_outbuffer[0] = REG_THR << 3 | _UART_CH << 1; //TX FIFO and UART Channel
|
||||
for ( int i = 1; i < sizeof(out)+1 ; i++){
|
||||
_outbuffer[i] = out[i-1];
|
||||
}
|
||||
|
||||
#ifdef DIAG_I2CDFplayer_data
|
||||
DIAG(F("SC16IS752: I2C: %s Sent packet function"), _I2CAddress.toString());
|
||||
for (int i = 0; i < sizeof _outbuffer; i++){
|
||||
DIAG(F("SC16IS752: Data _outbuffer[0x%x]: 0x%x"), i, _outbuffer[i]);
|
||||
}
|
||||
#endif
|
||||
|
||||
TX_fifo_lvl();
|
||||
if(FIFO_TX_LEVEL > 0){ //FIFO is empty
|
||||
I2CManager.write(_I2CAddress, _outbuffer, sizeof(_outbuffer), &_rb);
|
||||
//I2CManager.write(_I2CAddress, _outbuffer, sizeof(_outbuffer));
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
DIAG(F("SC16IS752: I2C: %s data transmit complete on UART: 0x%x"), _I2CAddress.toString(), _UART_CH);
|
||||
#endif
|
||||
} else {
|
||||
DIAG(F("I2CDFPlayer at: %s, TX FIFO not empty on UART: 0x%x"), _I2CAddress.toString(), _UART_CH);
|
||||
_deviceState = DEVSTATE_FAILED; // This should not happen
|
||||
}
|
||||
_commandSendTime = micros();
|
||||
}
|
||||
|
||||
uint16_t calcChecksum(uint8_t* packet)
|
||||
{
|
||||
uint16_t sum = 0;
|
||||
for (int i = 1; i < 7; i++)
|
||||
{
|
||||
sum += packet[i];
|
||||
}
|
||||
return -sum;
|
||||
}
|
||||
|
||||
void setChecksum(uint8_t* out)
|
||||
{
|
||||
uint16_t sum = calcChecksum(out);
|
||||
out[7] = (sum >> 8);
|
||||
out[8] = (sum & 0xff);
|
||||
}
|
||||
|
||||
// SC16IS752 functions
|
||||
// Initialise SC16IS752 only for this channel
|
||||
// First a software reset
|
||||
// Enable FIFO and clear TX & RX FIFO
|
||||
// Need to set the following registers
|
||||
// IOCONTROL set bit 1 and 2 to 0 indicating that they are GPIO
|
||||
// IODIR set all bit to 1 indicating al are output
|
||||
// IOSTATE set only bit 0 to 1 for UART 0, or only bit 1 for UART 1 //
|
||||
// LCR bit 7=0 divisor latch (clock division registers DLH & DLL, they store 16 bit divisor),
|
||||
// WORD_LEN, STOP_BIT, PARITY_ENA and PARITY_TYPE
|
||||
// MCR bit 7=0 clock divisor devide-by-1 clock input
|
||||
// DLH most significant part of divisor
|
||||
// DLL least significant part of divisor
|
||||
//
|
||||
// BAUD_RATE, WORD_LEN, STOP_BIT, PARITY_ENA and PARITY_TYPE have been defined and initialized
|
||||
//
|
||||
void Init_SC16IS752(){ // Return value is in _deviceState
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
DIAG(F("SC16IS752: Initialize I2C: %s , UART Ch: 0x%x"), _I2CAddress.toString(), _UART_CH);
|
||||
#endif
|
||||
uint16_t _divisor = (SC16IS752_XTAL_FREQ / PRESCALER) / (BAUD_RATE * 16);
|
||||
TEMP_REG_VAL = 0x08; // UART Software reset
|
||||
UART_WriteRegister(REG_IOCONTROL, TEMP_REG_VAL);
|
||||
TEMP_REG_VAL = 0x00; // Set pins to GPIO mode
|
||||
UART_WriteRegister(REG_IOCONTROL, TEMP_REG_VAL);
|
||||
TEMP_REG_VAL = 0xFF; //Set all pins as output
|
||||
UART_WriteRegister(REG_IODIR, TEMP_REG_VAL);
|
||||
UART_ReadRegister(REG_IOSTATE); // Read current state as not to overwrite the other GPIO pins
|
||||
TEMP_REG_VAL = _inbuffer[0];
|
||||
setGPIO(); // Set the audio mixer channel
|
||||
/*
|
||||
if (_UART_CH == 0){ // Set Audio mixer channel
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 0 to high
|
||||
} else { // must be UART 1
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 1 to high
|
||||
}
|
||||
UART_WriteRegister(REG_IOSTATE, TEMP_REG_VAL);
|
||||
*/
|
||||
TEMP_REG_VAL = 0x07; // Reset FIFO, clear RX & TX FIFO
|
||||
UART_WriteRegister(REG_FCR, TEMP_REG_VAL);
|
||||
TEMP_REG_VAL = 0x00; // Set MCR to all 0, includes Clock divisor
|
||||
UART_WriteRegister(REG_MCR, TEMP_REG_VAL);
|
||||
TEMP_REG_VAL = 0x80 | WORD_LEN | STOP_BIT | PARITY_ENA | PARITY_TYPE;
|
||||
UART_WriteRegister(REG_LCR, TEMP_REG_VAL); // Divisor latch enabled
|
||||
UART_WriteRegister(REG_DLL, (uint8_t)_divisor); // Write DLL
|
||||
UART_WriteRegister(REG_DLH, (uint8_t)(_divisor >> 8)); // Write DLH
|
||||
UART_ReadRegister(REG_LCR);
|
||||
TEMP_REG_VAL = _inbuffer[0] & 0x7F; // Disable Divisor latch enabled bit
|
||||
UART_WriteRegister(REG_LCR, TEMP_REG_VAL); // Divisor latch disabled
|
||||
|
||||
uint8_t status = _rb.status;
|
||||
if (status != I2C_STATUS_OK) {
|
||||
DIAG(F("SC16IS752: I2C: %s failed %S"), _I2CAddress.toString(), I2CManager.getErrorMessage(status));
|
||||
_deviceState = DEVSTATE_FAILED;
|
||||
} else {
|
||||
#ifdef DIAG_IO
|
||||
DIAG(F("SC16IS752: I2C: %s, _deviceState: %S"), _I2CAddress.toString(), I2CManager.getErrorMessage(status));
|
||||
#endif
|
||||
_deviceState = DEVSTATE_NORMAL; // If I2C state is OK, then proceed to initialize DFPlayer
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
// Read the Receive FIFO Level register (RXLVL), return a single unsigned integer
|
||||
// of nr of characters in the RX FIFO, bit 6:0, 7 not used, set to zero
|
||||
// value from 0 (0x00) to 64 (0x40) Only display if RX FIFO has data
|
||||
// The RX fifo level is used to check if there are enough bytes to process a frame
|
||||
void RX_fifo_lvl(){
|
||||
UART_ReadRegister(REG_RXLV);
|
||||
FIFO_RX_LEVEL = _inbuffer[0];
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
if (FIFO_RX_LEVEL > 0){
|
||||
//if (FIFO_RX_LEVEL > 0 && FIFO_RX_LEVEL < 10){
|
||||
DIAG(F("SC16IS752: At I2C: %s, UART channel: 0x%x, FIFO_RX_LEVEL: 0d%d"), _I2CAddress.toString(), _UART_CH, _inbuffer[0]);
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
// When a frame is transmitted from the DFPlayer to the serial port, and at the same time the CS is sending a 42 query
|
||||
// the following two frames from the DFPlayer are corrupt. This result in the receive buffer being out of sync and the
|
||||
// CS will complain and generate a timeout.
|
||||
// The RX fifo has corrupt data and need to be flushed, this function does that
|
||||
//
|
||||
void resetRX_fifo(){
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
DIAG(F("SC16IS752: At I2C: %s, UART channel: 0x%x, RX fifo reset"), _I2CAddress.toString(), _UART_CH);
|
||||
#endif
|
||||
TEMP_REG_VAL = 0x03; // Reset RX fifo
|
||||
UART_WriteRegister(REG_FCR, TEMP_REG_VAL);
|
||||
}
|
||||
|
||||
// Set or reset GPIO pin 0 and 1 depending on the UART ch
|
||||
// This function may be modified in a future release to enable all 8 pins to be set or reset with EX-Rail
|
||||
// for various auxilary functions
|
||||
void setGPIO(){
|
||||
UART_ReadRegister(REG_IOSTATE); // Get the current GPIO pins state from the IOSTATE register
|
||||
TEMP_REG_VAL = _inbuffer[0];
|
||||
if (_audioMixer == 1){ // set to audio mixer 1
|
||||
if (_UART_CH == 0){
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 0 to high
|
||||
} else { // must be UART 1
|
||||
TEMP_REG_VAL |= (0x01 << _UART_CH); //Set GPIO pin 1 to high
|
||||
}
|
||||
} else { // set to audio mixer 2
|
||||
if (_UART_CH == 0){
|
||||
TEMP_REG_VAL &= ~(0x01 << _UART_CH); //Set GPIO pin 0 to Low
|
||||
} else { // must be UART 1
|
||||
TEMP_REG_VAL &= ~(0x01 << _UART_CH); //Set GPIO pin 1 to Low
|
||||
}
|
||||
}
|
||||
UART_WriteRegister(REG_IOSTATE, TEMP_REG_VAL);
|
||||
_setamCmd = false;
|
||||
}
|
||||
|
||||
|
||||
// Read the Tranmit FIFO Level register (TXLVL), return a single unsigned integer
|
||||
// of nr characters free in the TX FIFO, bit 6:0, 7 not used, set to zero
|
||||
// value from 0 (0x00) to 64 (0x40)
|
||||
//
|
||||
void TX_fifo_lvl(){
|
||||
UART_ReadRegister(REG_TXLV);
|
||||
FIFO_TX_LEVEL = _inbuffer[0];
|
||||
#ifdef DIAG_I2CDFplayer
|
||||
// DIAG(F("SC16IS752: At I2C: %s, UART channel: 0x%x, FIFO_TX_LEVEL: 0d%d"), _I2CAddress.toString(), _UART_CH, FIFO_TX_LEVEL);
|
||||
#endif
|
||||
}
|
||||
|
||||
|
||||
//void UART_WriteRegister(I2CAddress _I2CAddress, uint8_t _UART_CH, uint8_t UART_REG, uint8_t Val, I2CRB &_rb){
|
||||
void UART_WriteRegister(uint8_t UART_REG, uint8_t Val){
|
||||
_outbuffer[0] = UART_REG << 3 | _UART_CH << 1;
|
||||
_outbuffer[1] = Val;
|
||||
#ifdef DIAG_I2CDFplayer_reg
|
||||
DIAG(F("SC16IS752: Write register at I2C: %s, UART channel: 0x%x, Register: 0x%x, Data: 0b%b"), _I2CAddress.toString(), _UART_CH, UART_REG, _outbuffer[1]);
|
||||
#endif
|
||||
I2CManager.write(_I2CAddress, _outbuffer, 2);
|
||||
}
|
||||
|
||||
|
||||
void UART_ReadRegister(uint8_t UART_REG){
|
||||
_outbuffer[0] = UART_REG << 3 | _UART_CH << 1; // _outbuffer[0] has now UART_REG and UART_CH
|
||||
I2CManager.read(_I2CAddress, _inbuffer, 1, _outbuffer, 1);
|
||||
// _inbuffer has the REG data
|
||||
#ifdef DIAG_I2CDFplayer_reg
|
||||
DIAG(F("SC16IS752: Read register at I2C: %s, UART channel: 0x%x, Register: 0x%x, Data: 0b%b"), _I2CAddress.toString(), _UART_CH, UART_REG, _inbuffer[0]);
|
||||
#endif
|
||||
}
|
||||
|
||||
// SC16IS752 General register set (from the datasheet)
|
||||
enum : uint8_t{
|
||||
REG_RHR = 0x00, // FIFO Read
|
||||
REG_THR = 0x00, // FIFO Write
|
||||
REG_IER = 0x01, // Interrupt Enable Register R/W
|
||||
REG_FCR = 0x02, // FIFO Control Register Write
|
||||
REG_IIR = 0x02, // Interrupt Identification Register Read
|
||||
REG_LCR = 0x03, // Line Control Register R/W
|
||||
REG_MCR = 0x04, // Modem Control Register R/W
|
||||
REG_LSR = 0x05, // Line Status Register Read
|
||||
REG_MSR = 0x06, // Modem Status Register Read
|
||||
REG_SPR = 0x07, // Scratchpad Register R/W
|
||||
REG_TCR = 0x06, // Transmission Control Register R/W
|
||||
REG_TLR = 0x07, // Trigger Level Register R/W
|
||||
REG_TXLV = 0x08, // Transmitter FIFO Level register Read
|
||||
REG_RXLV = 0x09, // Receiver FIFO Level register Read
|
||||
REG_IODIR = 0x0A, // Programmable I/O pins Direction register R/W
|
||||
REG_IOSTATE = 0x0B, // Programmable I/O pins State register R/W
|
||||
REG_IOINTENA = 0x0C, // I/O Interrupt Enable register R/W
|
||||
REG_IOCONTROL = 0x0E, // I/O Control register R/W
|
||||
REG_EFCR = 0x0F, // Extra Features Control Register R/W
|
||||
};
|
||||
|
||||
// SC16IS752 Special register set
|
||||
enum : uint8_t{
|
||||
REG_DLL = 0x00, // Division registers R/W
|
||||
REG_DLH = 0x01, // Division registers R/W
|
||||
};
|
||||
|
||||
// SC16IS752 Enhanced regiter set
|
||||
enum : uint8_t{
|
||||
REG_EFR = 0X02, // Enhanced Features Register R/W
|
||||
REG_XON1 = 0x04, // R/W
|
||||
REG_XON2 = 0x05, // R/W
|
||||
REG_XOFF1 = 0x06, // R/W
|
||||
REG_XOFF2 = 0x07, // R/W
|
||||
};
|
||||
|
||||
// DFPlayer commands and values
|
||||
enum : uint8_t{
|
||||
PLAY = 0x0F,
|
||||
VOL = 0x06,
|
||||
FOLDER = 0x2B, // Not a DFPlayer command, used to set folder nr where audio file is
|
||||
REPEATPLAY = 0x08,
|
||||
STOPPLAY = 0x16,
|
||||
EQ = 0x07, // Set equaliser, require parameter NORMAL, POP, ROCK, JAZZ, CLASSIC or BASS
|
||||
RESET = 0x0C,
|
||||
DACON = 0x1A,
|
||||
SETAM = 0x2A, // Set audio mixer 1 or 2 for this DFPLayer
|
||||
NORMAL = 0x00, // Equalizer parameters
|
||||
POP = 0x01,
|
||||
ROCK = 0x02,
|
||||
JAZZ = 0x03,
|
||||
CLASSIC = 0x04,
|
||||
BASS = 0x05,
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
#endif // IO_I2CDFPlayer_h
|
||||
69
IO_Template.h
Normal file
69
IO_Template.h
Normal file
|
|
@ -0,0 +1,69 @@
|
|||
|
||||
/*
|
||||
* Creation - a create() function and constructor are required;
|
||||
* Initialisation - a _begin() function is written (optional);
|
||||
* Background operations - a _loop() function is written (optional);
|
||||
* Operations - you can optionally supply any of _write() (digital) function, _writeAnalogue() function, _read() (digital) function and _readAnalogue() function.
|
||||
*
|
||||
*
|
||||
*
|
||||
*
|
||||
*
|
||||
*
|
||||
*/
|
||||
|
||||
|
||||
#ifndef IO_MYDEVICE_H
|
||||
#define IO_MYDEVICE_H
|
||||
|
||||
#include "IODevice.h"
|
||||
#include "DIAG.h" // for DIAG calls
|
||||
|
||||
class MyDevice: public IODevice {
|
||||
public:
|
||||
// Constructor
|
||||
MyDevice(VPIN firstVpin, int nPins) {
|
||||
_firstVpin = firstVpin;
|
||||
_nPins = min(nPins,16);
|
||||
// Other object initialisation here
|
||||
// ...
|
||||
addDevice(this);
|
||||
}
|
||||
static void create(VPIN firstVpin, int nPins, uint8_t i2cAddress) {
|
||||
new MyDevice(firstVpin, nPins);
|
||||
}
|
||||
private:
|
||||
void _begin() override {
|
||||
// Initialise device
|
||||
// ...
|
||||
}
|
||||
void _loop(unsigned long currentMicros) override {
|
||||
// Regular operations, e.g. acquire data
|
||||
// ...
|
||||
delayUntil(currentMicros + 10*1000UL); // 10ms till next entry
|
||||
}
|
||||
int _readAnalogue(VPIN vpin) override {
|
||||
// Return acquired data value, e.g.
|
||||
int pin = vpin - _firstVpin;
|
||||
return _value[pin];
|
||||
}
|
||||
int _read(VPIN vpin) override {
|
||||
// Return acquired data value, e.g.
|
||||
int pin = vpin - _firstVpin;
|
||||
return _value[pin];
|
||||
}
|
||||
void write(VPIN vpin, int value) override {
|
||||
// Do something with value , e.g. write to device.
|
||||
// ...
|
||||
}
|
||||
void writeAnalogue(VPIN vpin, int value) override {
|
||||
// Do something with value, e.g. write to device.
|
||||
// ...
|
||||
}
|
||||
void _display() override {
|
||||
DIAG(F("MyDevice Configured on Vpins:%d-%d %S"), _firstVpin, _firstVpin+_nPins-1,
|
||||
_deviceState == DEVSTATE_FAILED ? F("OFFLINE") : F(""));
|
||||
}
|
||||
uint16_t _value[16];
|
||||
};
|
||||
#endif // IO_MYDEVICE_H
|
||||
|
|
@ -71,8 +71,9 @@ Stream * WifiInterface::wifiStream;
|
|||
#elif defined(ARDUINO_NUCLEO_F413ZH) || defined(ARDUINO_NUCLEO_F429ZI) \
|
||||
|| defined(ARDUINO_NUCLEO_F446ZE) || defined(ARDUINO_NUCLEO_F412ZG) \
|
||||
|| defined(ARDUINO_NUCLEO_F439ZI)
|
||||
#define NUM_SERIAL 2
|
||||
#define NUM_SERIAL 3
|
||||
#define SERIAL1 Serial6
|
||||
#define SERIAL3 Serial2
|
||||
#else
|
||||
#warning This variant of Nucleo not yet explicitly supported
|
||||
#endif
|
||||
|
|
|
|||
|
|
@ -25,6 +25,16 @@
|
|||
//#include "IO_EXTurntable.h" // Turntable-EX turntable controller
|
||||
//#include "IO_EXFastClock.h" // FastClock driver
|
||||
//#include "IO_PCA9555.h" // 16-bit I/O expander (NXP & Texas Instruments).
|
||||
//#include "IO_CMRI.h" // CMRI nodes
|
||||
|
||||
//==========================================================================
|
||||
// also for CMRI connection using RS485 TTL module
|
||||
//==========================================================================
|
||||
// define UARt2 pins for ESP32 Rx=16, Tx=17 -- can conflict if sabertooth defined
|
||||
//HardwareSerial mySerial2(2); // use UART2
|
||||
//
|
||||
// for SERIAL_8N2 include this in config.h
|
||||
// #define ARDUINOCMRI_COMPATIBLE
|
||||
|
||||
//==========================================================================
|
||||
// The function halSetup() is invoked from CS if it exists within the build.
|
||||
|
|
@ -34,6 +44,36 @@
|
|||
|
||||
void halSetup() {
|
||||
|
||||
//==========================================================================
|
||||
// CMRI bus and nodes defined
|
||||
//==========================================================================
|
||||
// further explanation in IO_CMRI.h
|
||||
// this example is being used to test connection of existing CMRI device
|
||||
// add lines to myHal.cpp within halSetup()
|
||||
|
||||
// for ESP32
|
||||
//mySerial2.begin(9600, SERIAL_8N2, 16, 17); // ESP32 to define pins also check DCCTimerESP.cpp
|
||||
//CMRIbus::create(0, mySerial2, 9600, 500, 4); // for ESP32
|
||||
|
||||
// for Mega
|
||||
//CMRIbus::create(0, Serial3, 9600, 500, 38); // for Mega - Serial3 already defined
|
||||
// bus=0 always, unless multiple serial ports are used
|
||||
// baud=9600 to match setting in existing CMRI nodes
|
||||
// cycletime.. 500ms is default -- more frequent might be needed on master
|
||||
// pin.. DE/!RE pins tied together on TTL RS485 module.
|
||||
// pin 38 should work on Mega and F411RE (pin D38 aka PB12 on CN10_16)
|
||||
|
||||
//CMRInode::create(900, 72, 0, 4, 'M');
|
||||
//CMRInode::create(1000, 72, 0, 5, 'M');
|
||||
// bus=0 must agree with bus in CMRIbus
|
||||
// node=4 number to agree with node numbering
|
||||
// 'M' is for SMINI.
|
||||
// Starting VPin, Number of VPins=72 for SMINI
|
||||
//==========================================================================
|
||||
// end of CMRI
|
||||
//==========================================================================
|
||||
|
||||
|
||||
//=======================================================================
|
||||
// The following directives define auxiliary display devices.
|
||||
// These can be defined in addition to the system display (display
|
||||
|
|
@ -234,6 +274,23 @@ void halSetup() {
|
|||
// DFPlayer::create(10000, 10, Serial1);
|
||||
|
||||
|
||||
//=======================================================================
|
||||
// Play mp3 files from a Micro-SD card, using a DFPlayer MP3 Module on a SC16IS752 I2C Dual UART
|
||||
//=======================================================================
|
||||
// DFPlayer via NXP SC16IS752 I2C Dual UART. Each device has 2 UARTs on a single I2C address
|
||||
// Total nr of devices on an I2C bus is 16, with 2 UARTs on each address making a total of 32 UARTs per I2C bus
|
||||
// I2C address range 0x48 - 0x57
|
||||
// I2CDFPlayer::create(1st vPin,vPins, I2C address, UART ch);
|
||||
|
||||
// I2CDFPlayer::create(10000, 10, 0x48, 0);
|
||||
// I2CDFPlayer::create(10010, 10, 0x48, 1);
|
||||
|
||||
// Multiplexer example
|
||||
// I2CDFPlayer::create(10020, 10, {I2CMux_0, SubBus_0, 0x50}, 0);
|
||||
|
||||
|
||||
|
||||
|
||||
//=======================================================================
|
||||
// 16-pad capacitative touch key pad based on TP229 IC.
|
||||
//=======================================================================
|
||||
|
|
|
|||
128
mySetup_h_cmri.txt
Normal file
128
mySetup_h_cmri.txt
Normal file
|
|
@ -0,0 +1,128 @@
|
|||
// mySetup.h
|
||||
// defining CMRI accessories
|
||||
// CMRI connections defined in myHal.cpp
|
||||
//
|
||||
// this is for testing.
|
||||
SETUP("D CMD 1");
|
||||
// Turnouts defined in myAutomation.h can include descriptions which will appear in Engine Driver
|
||||
// Sensors and digital outputs do not require pre-definition for use in EXRAIL automation
|
||||
//
|
||||
// SMINI emulation node 24-input/48-outputs
|
||||
// the sketch I use
|
||||
// 16 or 24 input pins
|
||||
// 32 or 48 output pins
|
||||
//
|
||||
// Define 16 input pins 1000-1015
|
||||
SETUP("S 1000 1000 1");
|
||||
SETUP("S 1001 1001 1");
|
||||
SETUP("S 1002 1002 1");
|
||||
SETUP("S 1003 1003 1");
|
||||
SETUP("S 1004 1004 1");
|
||||
SETUP("S 1005 1005 1");
|
||||
SETUP("S 1006 1006 1");
|
||||
SETUP("S 1007 1007 1");
|
||||
SETUP("S 1008 1008 1");
|
||||
SETUP("S 1009 1009 1");
|
||||
SETUP("S 1010 1010 1");
|
||||
SETUP("S 1011 1011 1");
|
||||
SETUP("S 1012 1012 1");
|
||||
SETUP("S 1013 1013 1");
|
||||
SETUP("S 1014 1014 1");
|
||||
SETUP("S 1015 1015 1");
|
||||
//
|
||||
// define 16 turnouts using VPIN (for Throw/Close commands via CMRI)
|
||||
SETUP("T 1024 VPIN 1024");
|
||||
SETUP("T 1025 VPIN 1025");
|
||||
SETUP("T 1026 VPIN 1026");
|
||||
SETUP("T 1027 VPIN 1027");
|
||||
SETUP("T 1028 VPIN 1028");
|
||||
SETUP("T 1029 VPIN 1029");
|
||||
SETUP("T 1030 VPIN 1030");
|
||||
SETUP("T 1031 VPIN 1031");
|
||||
SETUP("T 1032 VPIN 1032");
|
||||
SETUP("T 1033 VPIN 1033");
|
||||
SETUP("T 1034 VPIN 1034");
|
||||
SETUP("T 1035 VPIN 1035");
|
||||
SETUP("T 1036 VPIN 1036");
|
||||
SETUP("T 1037 VPIN 1037");
|
||||
SETUP("T 1038 VPIN 1038");
|
||||
SETUP("T 1039 VPIN 1039");
|
||||
//
|
||||
// define 16 pins for digital outputs
|
||||
SETUP("Z 1040 1040 0");
|
||||
SETUP("Z 1041 1041 0");
|
||||
SETUP("Z 1042 1042 0");
|
||||
SETUP("Z 1043 1043 0");
|
||||
SETUP("Z 1044 1044 0");
|
||||
SETUP("Z 1045 1045 0");
|
||||
SETUP("Z 1046 1046 0");
|
||||
SETUP("Z 1047 1047 0");
|
||||
SETUP("Z 1048 1048 0");
|
||||
SETUP("Z 1049 1049 0");
|
||||
SETUP("Z 1050 1050 0");
|
||||
SETUP("Z 1051 1051 0");
|
||||
SETUP("Z 1052 1052 0");
|
||||
SETUP("Z 1053 1053 0");
|
||||
SETUP("Z 1054 1054 0");
|
||||
SETUP("Z 1055 1055 0");
|
||||
//
|
||||
// additional 16 outputs available 1056-1071
|
||||
//SETUP("Z 1056 1056 0");
|
||||
//
|
||||
// CMRI sketch used for testing available here
|
||||
// https://www.trainboard.com/highball/index.php?threads/24-in-48-out-card-for-jmri.116454/page-2#post-1141569
|
||||
//
|
||||
|
||||
// Define 16 input pins 900-915
|
||||
SETUP("S 900 900 1");
|
||||
SETUP("S 901 901 1");
|
||||
SETUP("S 902 902 1");
|
||||
SETUP("S 903 903 1");
|
||||
SETUP("S 904 904 1");
|
||||
SETUP("S 905 905 1");
|
||||
SETUP("S 906 906 1");
|
||||
SETUP("S 907 907 1");
|
||||
SETUP("S 908 908 1");
|
||||
SETUP("S 909 909 1");
|
||||
SETUP("S 910 910 1");
|
||||
SETUP("S 911 911 1");
|
||||
SETUP("S 912 912 1");
|
||||
SETUP("S 913 913 1");
|
||||
SETUP("S 914 914 1");
|
||||
SETUP("S 915 915 1");
|
||||
//
|
||||
// define 16 turnouts using VPIN (for Throw/Close commands via CMRI)
|
||||
SETUP("T 924 VPIN 924");
|
||||
SETUP("T 925 VPIN 925");
|
||||
SETUP("T 926 VPIN 926");
|
||||
SETUP("T 927 VPIN 927");
|
||||
SETUP("T 928 VPIN 928");
|
||||
SETUP("T 929 VPIN 929");
|
||||
SETUP("T 930 VPIN 930");
|
||||
SETUP("T 931 VPIN 931");
|
||||
SETUP("T 932 VPIN 932");
|
||||
SETUP("T 933 VPIN 933");
|
||||
SETUP("T 934 VPIN 934");
|
||||
SETUP("T 935 VPIN 935");
|
||||
SETUP("T 936 VPIN 936");
|
||||
SETUP("T 937 VPIN 937");
|
||||
SETUP("T 938 VPIN 938");
|
||||
SETUP("T 939 VPIN 939");
|
||||
//
|
||||
// define 16 pins for digital outputs
|
||||
SETUP("Z 940 940 0");
|
||||
SETUP("Z 941 941 0");
|
||||
SETUP("Z 942 942 0");
|
||||
SETUP("Z 943 943 0");
|
||||
SETUP("Z 944 944 0");
|
||||
SETUP("Z 945 945 0");
|
||||
SETUP("Z 946 946 0");
|
||||
SETUP("Z 947 947 0");
|
||||
SETUP("Z 948 948 0");
|
||||
SETUP("Z 949 949 0");
|
||||
SETUP("Z 950 950 0");
|
||||
SETUP("Z 951 951 0");
|
||||
SETUP("Z 952 952 0");
|
||||
SETUP("Z 953 953 0");
|
||||
SETUP("Z 954 954 0");
|
||||
SETUP("Z 955 955 0");
|
||||
|
|
@ -30,7 +30,6 @@ include_dir = .
|
|||
|
||||
[env]
|
||||
build_flags = -Wall -Wextra
|
||||
; monitor_filters = time
|
||||
|
||||
[env:samd21-dev-usb]
|
||||
platform = atmelsam
|
||||
|
|
@ -245,18 +244,32 @@ monitor_echo = yes
|
|||
|
||||
; Experimental - Ethernet work still in progress
|
||||
;
|
||||
; [env:Nucleo-F429ZI]
|
||||
; platform = ststm32
|
||||
; board = nucleo_f429zi
|
||||
; framework = arduino
|
||||
; lib_deps = ${env.lib_deps}
|
||||
; arduino-libraries/Ethernet @ ^2.0.1
|
||||
; stm32duino/STM32Ethernet @ ^1.3.0
|
||||
; stm32duino/STM32duino LwIP @ ^2.1.2
|
||||
; build_flags = -std=c++17 -Os -g2 -Wunused-variable
|
||||
; monitor_speed = 115200
|
||||
; monitor_echo = yes
|
||||
; upload_protocol = stlink
|
||||
[env:Nucleo-F429ZI]
|
||||
platform = ststm32
|
||||
board = nucleo_f429zi
|
||||
framework = arduino
|
||||
lib_deps = ${env.lib_deps}
|
||||
stm32duino/STM32Ethernet @ ^1.3.0
|
||||
stm32duino/STM32duino LwIP @ ^2.1.2
|
||||
build_flags = -std=c++17 -Os -g2 -Wunused-variable
|
||||
monitor_speed = 115200
|
||||
monitor_echo = yes
|
||||
upload_protocol = stlink
|
||||
|
||||
; Experimental - Ethernet work still in progress
|
||||
; Commented out as the F439ZI also needs variant files
|
||||
;
|
||||
[env:Nucleo-F439ZI]
|
||||
platform = ststm32
|
||||
board = nucleo_f439zi
|
||||
framework = arduino
|
||||
lib_deps = ${env.lib_deps}
|
||||
stm32duino/STM32Ethernet @ ^1.3.0
|
||||
stm32duino/STM32duino LwIP @ ^2.1.2
|
||||
build_flags = -std=c++17 -Os -g2 -Wunused-variable
|
||||
monitor_speed = 115200
|
||||
monitor_echo = yes
|
||||
upload_protocol = stlink
|
||||
|
||||
[env:Teensy3_2]
|
||||
platform = teensy
|
||||
|
|
|
|||
|
|
@ -3,14 +3,17 @@
|
|||
|
||||
#include "StringFormatter.h"
|
||||
|
||||
#define VERSION "5.2.20"
|
||||
#define VERSION "5.2.20ethCdf"
|
||||
// 5.2.20 - Check return of Ethernet.begin()
|
||||
// 5.2.19 - ESP32: Determine if the RMT hardware can handle DCC
|
||||
// 5.2.18 - Display network IP fix
|
||||
// 5.2.17 - ESP32 simplify network logic
|
||||
// 5.2.16 - Bugfix to allow for devices using the EX-IOExpander protocol to have no analogue or no digital pins
|
||||
// df - I2C DFPlayper capability
|
||||
// 5.2.15 - move call to CommandDistributor::broadcastPower() into the TrackManager::setTrackPower(*) functions
|
||||
// - add repeats to function packets that are not reminded in accordance with accessory packets
|
||||
// 5.2.14eth - Initial ethernet code for STM32F429ZI and F439ZI boards
|
||||
// C - CMRI RS485 connection
|
||||
// 5.2.14 - Reminder window DCC packet optimization
|
||||
// - Optional #define DISABLE_FUNCTION_REMINDERS
|
||||
// 5.2.13 - EXRAIL STEALTH
|
||||
|
|
|
|||
Loading…
Reference in New Issue
Block a user