From 480eb1bfde5c96119c3bf1bf9bcd9c51bb2a7a72 Mon Sep 17 00:00:00 2001 From: Barry Daniel Date: Sun, 6 Oct 2024 15:07:15 +1000 Subject: [PATCH] Delete myHal.cpp --- myHal.cpp | 363 ------------------------------------------------------ 1 file changed, 363 deletions(-) delete mode 100644 myHal.cpp diff --git a/myHal.cpp b/myHal.cpp deleted file mode 100644 index b6b9b36..0000000 --- a/myHal.cpp +++ /dev/null @@ -1,363 +0,0 @@ -// Sample myHal.cpp file. -// -// To use this file, copy it to myHal.cpp and uncomment the directives and/or -// edit them to satisfy your requirements. If you only want to use up to -// two MCP23017 GPIO Expander modules and/or up to two PCA9685 Servo modules, -// then you don't need this file as DCC++EX configures these for free! - -// Note that if the file has a .cpp extension it WILL be compiled into the build -// and the halSetup() function WILL be invoked. -// -// To prevent this, temporarily rename the file to myHal.txt or similar. -// - -// The #if directive prevent compile errors for Uno and Nano by excluding the -// HAL directives from the build. -#if !defined(IO_NO_HAL) - -// Include devices you need. -#include "IODevice.h" -//#include "IO_HALDisplay.h" // Auxiliary display devices (LCD/OLED) -//#include "IO_HCSR04.h" // Ultrasonic range sensor -//#include "IO_VL53L0X.h" // Laser time-of-flight sensor -//#include "IO_DFPlayer.h" // MP3 sound player -//#include "IO_TouchKeypad.h // Touch keypad with 16 keys -//#include "IO_EXTurntable.h" // Turntable-EX turntable controller -//#include "IO_EXFastClock.h" // FastClock driver -//#include "IO_PCA9555.h" // 16-bit I/O expander (NXP & Texas Instruments). -//#include "IO_I2CDFPlayer.h" // DFPlayer over I2C -#include "IO_EXSensorCAM.h" // sensorCAM driver - -//========================================================================== -// The function halSetup() is invoked from CS if it exists within the build. -// The setup calls are included between the open and close braces "{ ... }". -// Comments (lines preceded by "//") are optional. -//========================================================================== - -void halSetup() { - - I2CManager.setClock(100000); //to set i2c bus clock rate - - //======================================================================= - // The following directives define auxiliary display devices. - // These can be defined in addition to the system display (display - // number 0) that is defined in config.h. - // A write to a line which is beyond the length of the screen will overwrite - // the bottom line, unless the line number is 255 in which case the - // screen contents will scroll up before the text is written to the - // bottom line. - //======================================================================= - // - // Create a 128x32 OLED display device as display number 1 - // (line 0 is written by EX-RAIL 'SCREEN(1, 0, "text")'). - - //HALDisplay::create(1, 0x3d, 128, 32); - - // Create a 20x4 LCD display device as display number 2 - // (line 0 is written by EX-RAIL 'SCREEN(2, 0, "text")'). - - // HALDisplay::create(2, 0x27, 20, 4); - - - //======================================================================= - // User Add-ins - //======================================================================= - // User add-ins can be created when you want to do something that - // can't be done in EX-RAIL but does not merit a HAL driver. The - // user add-in is a C++ function that is executed periodically by the - // HAL subsystem. - - // Example: The function will be executed once per second and will display, - // on screen #3, the first eight entries (assuming an 8-line display) - // from the loco speed table. - - // Put the following block of code in myHal.cpp OUTSIDE of the - // halSetup() function: - // - // void updateLocoScreen() { - // for (int i=0; i<8; i++) { - // if (DCC::speedTable[i].loco > 0) { - // int speed = DCC::speedTable[i].speedCode; - // char direction = (speed & 0x80) ? 'R' : 'F'; - // speed = speed & 0x7f; - // if (speed > 0) speed = speed - 1; - // SCREEN(3, i, F("Loco:%4d %3d %c"), DCC::speedTable[i].loco, - // speed, direction); - // } - // } - // } - // - // Put the following line INSIDE the halSetup() function: - // - // UserAddin::create(updateLocoScreen, 1000); - // - - - //======================================================================= - // The following directive defines a PCA9685 PWM Servo driver module. - //======================================================================= - // The parameters are: - // First Vpin=100 - // Number of VPINs=16 (numbered 100-115) - // I2C address of module=0x40 - - //PCA9685::create(100, 16, 0x40); - - - //======================================================================= - // The following directive defines an MCP23017 16-port I2C GPIO Extender module. - //======================================================================= - // The parameters are: - // First Vpin=196 - // Number of VPINs=16 (numbered 196-211) - // I2C address of module=0x22 - - //MCP23017::create(196, 16, 0x22); - - - // Alternative form, which allows the INT pin of the module to request a scan - // by pulling Arduino pin 40 to ground. Means that the I2C isn't being polled - // all the time, only when a change takes place. Multiple modules' INT pins - // may be connected to the same Arduino pin. - - //MCP23017::create(196, 16, 0x22, 40); - - - //======================================================================= - // The following directive defines an MCP23008 8-port I2C GPIO Extender module. - //======================================================================= - // The parameters are: - // First Vpin=300 - // Number of VPINs=8 (numbered 300-307) - // I2C address of module=0x22 - - //MCP23008::create(300, 8, 0x22); - - - //======================================================================= - // The following directive defines a PCF8574 8-port I2C GPIO Extender module. - //======================================================================= - // The parameters are: - // First Vpin=200 - // Number of VPINs=8 (numbered 200-207) - // I2C address of module=0x23 - - //PCF8574::create(200, 8, 0x23); - - - // Alternative form using INT pin (see above) - - //PCF8574::create(200, 8, 0x23, 40); - - - //======================================================================= - // The following directive defines a PCF8575 16-port I2C GPIO Extender module. - //======================================================================= - // The parameters are: - // First Vpin=200 - // Number of VPINs=16 (numbered 200-215) - // I2C address of module=0x23 - - //PCF8575::create(200, 16, 0x23); - - - // Alternative form using INT pin (see above) - - //PCF8575::create(200, 16, 0x23, 40); - - //======================================================================= - // The following directive defines an HCSR04 ultrasonic ranging module. - //======================================================================= - // The parameters are: - // Vpin=2000 (only one VPIN per directive) - // Number of VPINs=1 - // Arduino pin connected to TRIG=30 - // Arduino pin connected to ECHO=31 - // Minimum trigger range=20cm (VPIN goes to 1 when <20cm) - // Maximum trigger range=25cm (VPIN goes to 0 when >25cm) - // Note: Multiple devices can be configured by using a different ECHO pin - // for each one. The TRIG pin can be shared between multiple devices. - // Be aware that the 'ping' of one device may be received by another - // device and position them accordingly! - - //HCSR04::create(2000, 30, 31, 20, 25); - //HCSR04::create(2001, 30, 32, 20, 25); - - - //======================================================================= - // The following directive defines a single VL53L0X Time-of-Flight range sensor. - //======================================================================= - // The parameters are: - // VPIN=5000 - // Number of VPINs=1 - // I2C address=0x29 (default for this chip) - // Minimum trigger range=200mm (VPIN goes to 1 when <20cm) - // Maximum trigger range=250mm (VPIN goes to 0 when >25cm) - - //VL53L0X::create(5000, 1, 0x29, 200, 250); - - // For multiple VL53L0X modules, add another parameter which is a VPIN connected to the - // module's XSHUT pin. This allows the modules to be configured, at start, - // with distinct I2C addresses. In this case, the address 0x29 is only used during - // initialisation to configure each device in turn with the desired unique I2C address. - // The examples below have the modules' XSHUT pins connected to the first two pins of - // the first MCP23017 module (164 and 165), but Arduino pins may be used instead. - // The first module here is given I2C address 0x30 and the second is 0x31. - - //VL53L0X::create(5000, 1, 0x30, 200, 250, 164); - //VL53L0X::create(5001, 1, 0x31, 200, 250, 165); - - - //======================================================================= - // Play mp3 files from a Micro-SD card, using a DFPlayer MP3 Module. - //======================================================================= - // Parameters: - // 10000 = first VPIN allocated. - // 10 = number of VPINs allocated. - // Serial1 = name of serial port (usually Serial1 or Serial2). - // With these parameters, up to 10 files may be played on pins 10000-10009. - // Play is started from EX-RAIL with SET(10000) for first mp3 file, SET(10001) - // for second file, etc. Play may also be initiated by writing an analogue - // value to the first pin, e.g. ANOUT(10000,23,0,0) will play the 23rd mp3 file. - // ANOUT(10000,23,30,0) will do the same thing, as well as setting the volume to - // 30 (maximum value). - // Play is stopped by RESET(10000) (or any other allocated VPIN). - // Volume may also be set by writing an analogue value to the second pin for the player, - // e.g. ANOUT(10001,30,0,0) sets volume to maximum (30). - // The EX-RAIL script may check for completion of play by calling WAITFOR(pin), which will only proceed to the - // following line when the player is no longer busy. - // E.g. - // SEQUENCE(1) - // AT(164) // Wait for sensor attached to pin 164 to activate - // SET(10003) // Play fourth MP3 file - // LCD(4, "Playing") // Display message on LCD/OLED - // WAITFOR(10003) // Wait for playing to finish - // LCD(4, "") // Clear LCD/OLED line - // FOLLOW(1) // Go back to start - - // DFPlayer::create(10000, 10, Serial1); - - - //======================================================================= - // Play mp3 files from a Micro-SD card, using a DFPlayer MP3 Module on a SC16IS750/SC16IS752 I2C UART - //======================================================================= - // DFPlayer via NXP SC16IS752 I2C Dual UART. - // I2C address range 0x48 - 0x57 - // - // Generic format: - // I2CDFPlayer::create(1st vPin, vPins, I2C address, xtal); - // Parameters: - // 1st vPin : First virtual pin that EX-Rail can control to play a sound, use PLAYSOUND command (alias of ANOUT) - // vPins : Total number of virtual pins allocated (1 vPin is supported currently) - // 1st vPin for UART 0 - // I2C Address : I2C address of the serial controller, in 0x format - // xtal : 0 for 1.8432Mhz, 1 for 14.7456Mhz - // - // The vPin is also a pin that can be read with the WAITFOR(vPin) command indicating if the DFPlayer has finished playing a track - // - - // I2CDFPlayer::create(10000, 1, 0x48, 1); - // - // Configuration example on a multiplexer - // I2CDFPlayer::create(10000, 1, {I2CMux_0, SubBus_0, 0x48}, 1); - - - - //======================================================================= - // 16-pad capacitative touch key pad based on TP229 IC. - //======================================================================= - // Parameters below: - // 11000 = first VPIN allocated - // 16 = number of VPINs allocated - // 25 = local GPIO pin number for clock signal - // 24 = local GPIO pin number for data signal - // - // Pressing the key pads numbered 1-16 cause each of the nominated digital VPINs - // (11000-11015 in this case) to be activated. - - // TouchKeypad::create(11000, 16, 25, 24); - - - //======================================================================= - // The following directive defines an EX-Turntable turntable instance. - //======================================================================= - // EXTurntable::create(VPIN, Number of VPINs, I2C Address) - // - // The parameters are: - // VPIN=600 - // Number of VPINs=1 (Note there is no reason to change this) - // I2C address=0x60 - // - // Note that the I2C address is defined in the EX-Turntable code, and 0x60 is the default. - - //EXTurntable::create(600, 1, 0x60); - - - //======================================================================= - // The following directive defines an EX-IOExpander instance. - //======================================================================= - // EXIOExpander::create(VPIN, Number of VPINs, I2C Address) - // - // The parameters are: - // VPIN=an available Vpin - // Number of VPINs=pin count (must match device in use as per documentation) - // I2C address=an available I2C address (default 0x65) - // - // Note that the I2C address is defined in the EX-IOExpander code, and 0x65 is the default. - // The example is for an Arduino Nano. - - //EXIOExpander::create(800, 18, 0x65); - -EXIOExpander::create(800, 18, 0x65); // NanoEXIOExpander::create(820, 18, 0x75); // Nano -//EXSensorCAM::create(840, 18, 0x85); // Nano -//EXIOExpander::create(880, 18, 0x95); // Nano -//EXIOExpander::create(780, 18, 0xA5); // Nanoc -//EXIOExpander::create(600, 18, 0xB5); // Nano -//EXIOExpander::create(500, 18, 0xC5); // Nano - - - //======================================================================= - // The following directive defines a rotary encoder instance. - //======================================================================= - // The parameters are: - // firstVpin = First available Vpin to allocate - // numPins= Number of Vpins to allocate, can be either 1 to 3 - // i2cAddress = Available I2C address (default 0x67) - - //RotaryEncoder::create(firstVpin, numPins, i2cAddress); - //RotaryEncoder::create(700, 1, 0x67); - //RotaryEncoder::create(700, 2, 0x67); - //RotaryEncoder::create(700, 3, 0x67); - - //======================================================================= - // The following directive defines an EX-FastClock instance. - //======================================================================= - // EXFastCLock::create(I2C Address) - // - // The parameters are: - // - // I2C address=0x55 (decimal 85) - // - // Note that the I2C address is defined in the EX-FastClock code, and 0x55 is the default. - - - // EXFastClock::create(0x55); - - //======================================================================= - // The following directive defines an ESP32-CAM instance. - //======================================================================= - // EXSensorCAM::create(VPIN, Number of VPINs, I2C Address) - // - // The parameters are: - // VPIN=an available Vpin as start of block of consecutive sensors (up to 80) - // #define SENSORCAM_VPIN0 #00 in config.h if not using 700. - // Number of VPINs=pin count (must not exceed 80) - // I2C address=an available I2C address (default 0x11) - // - // EXSensorCAM::create(700, 80, 0x11); //preference is now to use HAL(700 80 0x11) in myAutomation.h - EXSensorCAM::create(700, 80, 0x11); - //EXSensorCAM::create(600, 80, 0x12); //alternate or second CAM device address creation - //preference is now to use HAL(EXSensorCAM 700 80 0x11) in myAutomation.h rather than :create - } - -#endif