Implemebnt DCC API layer

CVReader.ino

@@ -1,4 +1,4 @@
-#include "DCCWaveform.h"
+#include "DCC.h"
 #include "DIAG.h"
 
 /* this code is here to test the waveforwe generator and reveal the issues involved in programming track operations.
@@ -16,18 +16,17 @@
  */
 
 
-bool verifyCV(int cv, byte bValue);
+
-int readCv(int cv);
 const int cvnums[]={1,2,3,4,5,17,18,19,21,22,29};
 
 void setup() {
   Serial.begin(115200);
-  DCCWaveform::begin();
+  DCC::begin();
   
   DIAG(F("\n===== CVReader begin ==============================\n"));
   
   for (byte x=0;x<sizeof(cvnums)/sizeof(cvnums[0]);x++) {
-    int value=readCV(cvnums[x]);
+    int value=DCC::readCV(cvnums[x]);
     DIAG(F("\nCV %d = %d  0x%x  %s"),cvnums[x],value,value, value>=0?" VERIFIED OK":"FAILED VERIFICATION"); 
   }
   
@@ -35,48 +34,5 @@ void setup() {
 }
 
 void loop() {
-  DCCWaveform::loop();
+  DCC::loop();
   }
-
-// Two helpers to make API functions look simpler
-
-byte cv1(byte opcode, int cv) {
-  cv--;
-  return (highByte(cv) & (byte)0x03) | opcode;
-}
-byte cv2(int cv) {
-  cv--;
-  return lowByte(cv);
-}
-
-// The functions below are lifted from the DCCApi and then fixed up 
-// Once reliable, tha DCCApi should be updated to match 
-bool verifyCV(int cv, byte value) {
-   byte message[] = {
-    cv1(0x74,cv)  ,   // set-up to re-verify entire byte
-    cv2(cv),
-    value
-    };
-  
-  DCCWaveform::progTrack.schedulePacket(message, sizeof(message), 5);  
-  return DCCWaveform::progTrack.getAck();
-}
-
-int readCV(int cv) 
-{
-  
-  byte message[]={  cv1(0x78,cv)  ,   // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
-                   cv2(cv),
-                   0};    // trailing zero will be updated in loop below
-
-  byte value = 0;
-
-  for (int i = 0; i<8; i++) {
-    message[2] = 0xE8 + i;
-    DCCWaveform::progTrack.schedulePacket(message,sizeof(message), 4);                // NMRA recommends 5 read packets
-    value+= (DCCWaveform::progTrack.getAck()<<i);
-  }
-  
-  //  DIAG(F("\n*** readCV(%d) = %d ******\n"),cv,value);
-  return verifyCV(cv,value)?value:-1;
-}

DCC.cpp

@@ -0,0 +1,208 @@
+#include "DCC.h"
+#include "DCCWaveform.h"
+#include "DIAG.h"
+// This module is responsible for converting API calls into
+// messages to be sent to the waveform generator.
+// It has no visibility of the hardware, timers, interrupts
+// nor of the waveform issues such as preambles, start bits checksums or cutouts.
+//
+// Nor should it have to deal with JMRI responsess other than the OK/FAIL
+// or cv value returned. I will move that back to the JMRI interface later
+//
+// The interface to the waveform generator is narrowed down to merely:
+//   Scheduling a message on the prog or main track using a function
+//   Obtaining ACKs from the prog track using a function
+//   There are no volatiles here.
+
+void DCC::begin() {
+  DCCWaveform::begin();
+}
+
+void DCC::setThrottle( uint16_t cab, uint8_t tSpeed, bool tDirection)  {
+  setThrottle2(cab, tSpeed, tDirection);
+  // retain speed for loco reminders
+  updateLocoReminder(cab, tSpeed, tDirection );
+}
+
+void DCC::setThrottle2( uint16_t cab, uint8_t tSpeed, bool tDirection)  {
+  uint8_t b[5];
+  uint8_t nB = 0;
+
+  if (cab > 127)
+    b[nB++] = highByte(cab) | 0xC0;    // convert train number into a two-byte address
+
+  b[nB++] = lowByte(cab);
+  b[nB++] = 0x3F;                      // 128-step speed control byte
+  if (tSpeed > 0)
+    b[nB++] = tSpeed + (tSpeed > 0) + tDirection * 128; // max speed is 126, but speed codes range from 2-127 (0=stop, 1=emergency stop)
+  else {
+    b[nB++] = 1;
+    tSpeed = 0;
+  }
+
+  DCCWaveform::mainTrack.schedulePacket(b, nB, 0);
+}
+
+void DCC::setFunction(int cab, byte byte1)  {
+  uint8_t b[4];
+  uint8_t nB = 0;
+
+  if (cab > 127)
+    b[nB++] = highByte(cab) | 0xC0;    // convert train number into a two-byte address
+  b[nB++] = lowByte(cab);
+  b[nB++] = (byte1 | 0x80) & 0xBF;
+
+  DCCWaveform::mainTrack.schedulePacket(b, nB, 4);     // Repeat the packet four times
+}
+
+void DCC::setFunction(int cab, byte byte1, byte byte2)  {
+  byte b[5];
+  byte nB = 0;
+
+  if (cab > 127)
+    b[nB++] = highByte(cab) | 0xC0;    // convert train number into a two-byte address
+  b[nB++] = lowByte(cab);
+  b[nB++] = (byte1 | 0xDE) & 0xDF;   // for safety this guarantees that first byte will either be 0xDE (for F13-F20) or 0xDF (for F21-F28)
+  b[nB++] = byte2;
+
+  DCCWaveform::mainTrack.schedulePacket(b, nB, 4);     // Repeat the packet four times
+}
+
+void DCC::setAccessory(int address, byte number, bool activate) {
+  byte b[3];                      // save space for checksum byte
+
+  b[0] = address % 64 + 128;                                     // first byte is of the form 10AAAAAA, where AAAAAA represent 6 least signifcant bits of accessory address
+  b[1] = ((((address / 64) % 8) << 4) + (number % 4 << 1) + activate % 2) ^ 0xF8; // second byte is of the form 1AAACDDD, where C should be 1, and the least significant D represent activate/deactivate
+
+  DCCWaveform::mainTrack.schedulePacket(b, 2, 4);      // Repeat the packet four times
+}
+
+void DCC::writeCVByteMain(int cab, int cv, byte bValue)  {
+  byte b[6];                      // save space for checksum byte
+  byte nB = 0;
+  if (cab > 127)
+    b[nB++] = highByte(cab) | 0xC0;    // convert train number into a two-byte address
+
+  b[nB++] = lowByte(cab);
+  b[nB++] = cv1(0xEC, cv); // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
+  b[nB++] = cv2(cv);
+  b[nB++] = bValue;
+
+  DCCWaveform::mainTrack.schedulePacket(b, nB, 4);
+}
+
+void DCC::writeCVBitMain(int cab, int cv, byte bNum, bool bValue)  {
+  byte b[6];                      // save space for checksum byte
+  byte nB = 0;
+  bValue = bValue % 2;
+  bNum = bNum % 8;
+
+  if (cab > 127)
+    b[nB++] = highByte(cab) | 0xC0;    // convert train number into a two-byte address
+
+  b[nB++] = lowByte(cab);
+  b[nB++] = cv1(0xE8, cv); // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
+  b[nB++] = cv2(cv);
+  b[nB++] = 0xF0 + bValue * 8 + bNum;
+
+  DCCWaveform::mainTrack.schedulePacket(b, nB, 4);
+}
+
+bool  DCC::writeCVByte(int cv, byte bValue)  {
+  uint8_t message[] = {cv1(0x7C, cv), cv2(cv), bValue};
+  DCCWaveform::progTrack.schedulePacket(message, sizeof(message), 6);           // NMRA recommends 6 write or reset packets for decoder recovery time
+  return verifyCV(cv, bValue);
+}
+
+
+bool DCC::writeCVBit(int cv, byte bNum, bool bValue)  {
+  bValue = bValue % 2;
+  bNum = bNum % 8;
+  uint8_t message[] = {cv1(0x78, cv), cv2(cv), 0xF0 + bValue * 8 + bNum};
+  DCCWaveform::progTrack.schedulePacket(message, sizeof(message), 6);           // NMRA recommends 6 write or reset packets for decoder recovery time
+
+  /* TODO... what is the verify opcode here?
+    bitWrite(message[2],4,1);              // change instruction code from Write Bit to Verify Bit
+    DCCWaveform::progTrack.schedulePacket(message,sizeof(message),6);             // NMRA recommends 6 write or reset packets for decoder recovery time
+  */
+
+  return DCCWaveform::progTrack.getAck();
+}
+
+
+int DCC::readCV(int cv)  {
+  byte message[] = {  cv1(0x78, cv)  , // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
+                      cv2(cv),
+                      0
+                   };    // trailing zero will be updated in loop below
+
+  byte value = 0;
+
+  // get each bit individually
+  for (int i = 0; i < 8; i++) {
+    message[2] = 0xE8 + i;
+    DCCWaveform::progTrack.schedulePacket(message, sizeof(message), 4);               // NMRA recommends 5 read packets
+    value += (DCCWaveform::progTrack.getAck() << i);
+  }
+
+  return verifyCV(cv, value) ? value : -1;
+}
+
+void DCC::loop()  {
+  DCCWaveform::loop(); // powwer overload checks
+  // if the main track transmitter still has a pending packet, skip this loop.
+  if ( DCCWaveform::mainTrack.packetPending) return;
+
+  // each time around the Arduino loop, we resend a loco speed packet reminder
+  for (; nextLoco < MAX_LOCOS; nextLoco++) {
+    if (speedTable[nextLoco].loco > 0) {
+      setThrottle2(speedTable[nextLoco].loco, speedTable[nextLoco].speed, speedTable[nextLoco].forward);
+      nextLoco++;
+      return;
+    }
+  }
+  for (nextLoco = 0; nextLoco < MAX_LOCOS; nextLoco++) {
+    if (speedTable[nextLoco].loco > 0) {
+      setThrottle2(speedTable[nextLoco].loco, speedTable[nextLoco].speed, speedTable[nextLoco].forward);
+      nextLoco++;
+      return;
+    }
+  }
+}
+
+///// Private helper functions below here /////////////////////
+byte DCC::cv1(byte opcode, int cv)  {
+  cv--;
+  return (highByte(cv) & (byte)0x03) | opcode;
+}
+byte DCC::cv2(int cv)  {
+  cv--;
+  return lowByte(cv);
+}
+
+bool DCC::verifyCV(int cv, byte value) {
+  byte message[] = { cv1(0x74, cv), cv2(cv), value};
+  DCCWaveform::progTrack.schedulePacket(message, sizeof(message), 5);
+  return DCCWaveform::progTrack.getAck();
+}
+
+
+void  DCC::updateLocoReminder(int loco, byte tSpeed, bool forward) {
+  // determine speed reg for this loco
+  int reg;
+  int firstEmpty = MAX_LOCOS;
+  for (reg = 0; reg < MAX_LOCOS; reg++) {
+    if (speedTable[reg].loco == loco) break;
+    if (speedTable[reg].loco == 0 && firstEmpty == MAX_LOCOS) firstEmpty = reg;
+  }
+  if (reg == MAX_LOCOS) reg = firstEmpty;
+  if (reg >= MAX_LOCOS) {
+    DIAG(F("\nToo many locos\n"));
+    return;
+  }
+  speedTable[reg].loco = loco;
+  speedTable[reg].speed = tSpeed;
+  speedTable[reg].forward = forward;
+}
+DCC::LOCO DCC::speedTable[MAX_LOCOS];
+int DCC::nextLoco=0;

DCC.h

@@ -0,0 +1,37 @@
+#include <Arduino.h>
+const byte MAX_LOCOS=200;
+
+
+class DCC {
+  public:
+
+  static void begin();
+  static void loop();
+
+  // Public DCC API functions
+  static void setThrottle( uint16_t cab, uint8_t tSpeed, bool tDirection);
+  static int  readCV(int cv);
+  static bool writeCVByte(int cv, byte bValue) ;
+  static bool writeCVBit(int cv, byte bNum, bool bValue);
+  static void writeCVByteMain(int cab, int cv, byte bValue);
+  static void writeCVBitMain(int cab, int cv, byte bNum, bool bValue);
+  static void setFunction( int cab, byte fByte, byte eByte);
+  static void setFunction( int cab, byte fByte);
+  static void setAccessory(int aAdd, byte aNum, bool activate) ;
+  static bool writeTextPacket( byte *b, int nBytes);
+
+private: 
+  struct LOCO {
+     int loco;
+       byte speed;
+       bool forward;
+  };
+  static bool verifyCV(int cv,byte bValue);
+  static void setThrottle2( uint16_t cab, uint8_t tSpeed, bool tDirection);
+  static void updateLocoReminder(int loco, byte tSpeed, bool forward);
+  static int nextLoco;
+  static LOCO speedTable[MAX_LOCOS];
+  static byte cv1(byte opcode, int cv);
+  static byte cv2(int cv);
+  
+};