Merge 3da4cb0961 into 3b162996ad

CommandDistributor.cpp

@@ -181,7 +181,20 @@ void CommandDistributor::setClockTime(int16_t clocktime, int8_t clockrate, byte
     case 1:
       if (clocktime != lastclocktime){
         // CAH. DIAG removed because LCD does it anyway. 
-        LCD(6,F("Clk Time:%d Sp %d"), clocktime, clockrate);
+
+        #ifndef FASTCLOCK_READABLE
+          LCD(6,F("Clk Time: %d Sp %d"), clocktime, clockrate);
+        #else
+          // Make Time readable
+          int hours = clocktime / 60;
+          int minutes = clocktime - (hours * 60);
+          int hoursH = hours / 10;
+          int hoursL  = hours - (hoursH * 10);
+          int minutesH = minutes / 10;
+          int minutesL  = minutes - (minutesH * 10);
+          LCD(6,F("Clk Time: %d%d:%d%d Sp %d"), hoursH, hoursL, minutesH, minutesL, clockrate);
+        #endif
+        
         // look for an event for this time
         RMFT2::clockEvent(clocktime,1);
         // Now tell everyone else what the time is.

I2CManager.cpp

@@ -48,6 +48,10 @@
 static const FSH * guessI2CDeviceType(uint8_t address) {
   if (address >= 0x20 && address <= 0x26)
     return F("GPIO Expander");
+#ifdef FAST_CLOCK_I2C
+  else if (address == FAST_CLOCK_I2C)
+    return F("Fast Clock");
+#endif
   else if (address == 0x27)
     return F("GPIO Expander or LCD Display");
   else if (address == 0x29)
@@ -363,4 +367,4 @@ void I2CAddress::toHex(const uint8_t value, char *buffer) {
 
 /* static */ bool I2CAddress::_addressWarningDone = false;
 
-#endif
+#endif

IODevice.cpp

@@ -27,6 +27,12 @@
 #include "IO_MCP23017.h"
 #include "DCCTimer.h"
 
+#if !defined(IO_NO_HAL)
+  #ifdef FAST_CLOCK_I2C
+    #include "IO_EXFastClock.h"  // FastClock driver
+  #endif
+#endif
+
 #if defined(ARDUINO_ARCH_AVR) || defined(ARDUINO_ARCH_MEGAAVR)
 #define USE_FAST_IO
 #endif
@@ -75,6 +81,11 @@ void IODevice::begin() {
   } else {
     DIAG(F("Default PCA9685 at I2C 0x41 disabled due to configured user device"));
   }
+
+  #ifdef FAST_CLOCK_I2C
+    DIAG(F("EXFastClock::create"));
+    EXFastClock::create(FAST_CLOCK_I2C);
+  #endif
   
   // Predefine two MCP23017 module 0x20/0x21 if no conflicts
   // Allocates 32 pins 164-195
@@ -582,4 +593,3 @@ bool ArduinoPins::fastReadDigital(uint8_t pin) {
 #endif
   return result;
 }
-

IO_EXFastclock.h

@@ -56,12 +56,12 @@ static void create(I2CAddress i2cAddress) {
   // XXXX change thistosave2 bytes
   if (_checkforclock == 0) {
       FAST_CLOCK_EXISTS = true;
-      //DIAG(F("I2C Fast Clock found at %s"), i2cAddress.toString());
+      DIAG(F("I2C Fast Clock found at %s"), i2cAddress.toString());
       new EXFastClock(i2cAddress); 
     }
     else {
       FAST_CLOCK_EXISTS = false;
-      //DIAG(F("No Fast Clock found"));
+      DIAG(F("No Fast Clock found"));
       LCD(6,F("CLOCK NOT FOUND"));
     }
     
@@ -95,7 +95,8 @@ void _loop(unsigned long currentMicros) override{
   if (FAST_CLOCK_EXISTS==true) {
       uint8_t readBuffer[3];
       byte a,b;
-      #ifdef EXRAIL_ACTIVE
+      // I would like to use the FastClock without EXRAIL
+      // #ifdef EXRAIL_ACTIVE
         I2CManager.read(_I2CAddress, readBuffer, 3);
         // XXXX change this to save a few bytes
         a = readBuffer[0];
@@ -110,7 +111,7 @@ void _loop(unsigned long currentMicros) override{
         // Clock interval is 60/ clockspeed i.e 60/b seconds
         delayUntil(currentMicros + ((60/b) * 1000000));  
      
-      #endif
+      // #endif
     
   }
 }

README.md

@@ -1,3 +1,7 @@
+# My (FranziHH) DCC++ Ex Hardware
+<img src="/images/IMG_5870_1.jpg" height="400px" title="DCC++ Ex Hardware">
+
+
 # What is DCC++ EX?
 DCC++ EX is the organization maintaining several codebases that together represent a fully open source DCC system. Currently, this includes the following:
 

WifiInterface.cpp

@@ -363,11 +363,17 @@ wifiSerialState WifiInterface::setup2(const FSH* SSid, const FSH* password,
       }
       ipString[ipLen]=ipChar;
     }
-    LCD(4,F("%s"),ipString);  // There is not enough room on some LCDs to put a title to this      
+    #ifndef PRINT_IP_PORT_SINGLE_LINE
+      LCD(4,F("%s"),ipString);  // There is not enough room on some LCDs to put a title to this    
+    #else
+      LCD(4,F("%s:%d"),ipString,port); // *** Single IP:Port  
+    #endif
   }
   // suck up anything after the IP. 
   if (!checkForOK(1000, true, false)) return WIFI_DISCONNECTED;
-  LCD(5,F("PORT=%d"),port);
+  #ifndef PRINT_IP_PORT_SINGLE_LINE
+    LCD(5,F("PORT=%d"),port);
+  #endif
    
   return WIFI_CONNECTED;
 }

config.example.h

@@ -167,6 +167,9 @@ The configuration file for DCC-EX Command Station
 //  *  #define SCROLLMODE 2 is by row (move up 1 row at a time).
 #define SCROLLMODE 1
 
+// Shows IP and Port on Display in a single line
+// #define PRINT_IP_PORT_SINGLE_LINE
+
 /////////////////////////////////////////////////////////////////////////////////////
 // DISABLE EEPROM
 //
@@ -239,7 +242,10 @@ The configuration file for DCC-EX Command Station
 // SAMD/SAMC and STM32 have up to 6.)
 // To monitor a throttle on one or more serial ports, uncomment the defines below.
 // NOTE: do not define here the WiFi shield serial port or your wifi will not work.
-//
+// -------------------------------------
+// For Use with FastClock serial: uncomment the needed serial Port and 
+// FastClock will work, no further actions are needed
+// -------------------------------------
 //#define SERIAL1_COMMANDS
 //#define SERIAL2_COMMANDS
 //#define SERIAL3_COMMANDS
@@ -247,6 +253,17 @@ The configuration file for DCC-EX Command Station
 //#define SERIAL5_COMMANDS
 //#define SERIAL6_COMMANDS
 //
+// -------------------------------------
+// FastClock with I2C
+// uncomment the following Line and Set the used I2C Address
+//#define FAST_CLOCK_I2C 0x55 // default is 0x55
+// -------------------------------------
+//
+// -------------------------------------
+// FastClock in HH:MM on Display
+//#define FASTCLOCK_READABLE
+// -------------------------------------
+//
 // BLUETOOTH SERIAL ON ESP32
 // On ESP32 you have the possibility to use the builtin BT serial to connect to
 // the CS.