Merge 2c133da140 into c518dcdc0b

Commented MAX_LOCOS
Lowered the default Max for Uno CS from 30 to 10

DCC.h

@@ -43,9 +43,9 @@ const uint16_t LONG_ADDR_MARKER = 0x4000;
 // Allocations with memory implications..!
 // Base system takes approx 900 bytes + 8 per loco. Turnouts, Sensors etc are dynamically created
 #if defined(HAS_ENOUGH_MEMORY)
-const byte MAX_LOCOS = 50;
-#else
-const byte MAX_LOCOS = 30;
+const byte MAX_LOCOS = 50;  // Default 50 for Mega2560,  Increase for ESP32 and STM32 Nucleo 
+#else                       // Adjust Max Locos as needed.
+const byte MAX_LOCOS = 10;  // Lower Max Loco for Uno CS, Recommended as a JMRI DecoderPro Programming Station 
 #endif
 
 class DCC

DCCEXParser.cpp

@@ -642,6 +642,13 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
 
     case 'F': // New command to call the new Loco Function API <F cab func 1|0>
         if(params!=3) break; 
+        
+        if (p[1]=="DCFREQ"_hk) { // <F cab DCFREQ 0..3>
+          if (p[2]<0 || p[2]>3) break;
+          DCC::setDCFreq(p[0],p[2]);
+          return;    
+        }
+
         if (Diag::CMD)
             DIAG(F("Setting loco %d F%d %S"), p[0], p[1], p[2] ? F("ON") : F("OFF"));
         if (DCC::setFn(p[0], p[1], p[2] == 1)) return;

EXRAIL2.cpp

@@ -628,14 +628,16 @@ void RMFT2::loop2() {
     skipIf=blinkState!=at_timeout;
     break;
     
-  case OPCODE_AFTER: // waits for sensor to hit and then remain off for 0.5 seconds. (must come after an AT operation)
+  case OPCODE_AFTER: // waits for sensor to hit and then remain off for x mS. 
+    // Note, this must come after an AT operation, which is 
+    // automatically inserted by the AFTER macro. 
     if (readSensor(operand)) {
-      // reset timer to half a second and keep waiting
+      // reset timer and keep waiting
       waitAfter=millis();
       delayMe(50);
       return;
     }
-    if (millis()-waitAfter < 500 ) return;
+    if (millis()-waitAfter < getOperand(1) ) return;
     break;
 
   case OPCODE_AFTEROVERLOAD: // waits for the power to be turned back on - either by power routine or button

EXRAIL2MacroReset.h

@@ -195,7 +195,7 @@
 #ifndef RMFT2_UNDEF_ONLY
 #define ACTIVATE(addr,subaddr)
 #define ACTIVATEL(addr)
-#define AFTER(sensor_id)
+#define AFTER(sensor_id,timer...)
 #define AFTEROVERLOAD(track_id)
 #define ALIAS(name,value...)
 #define AMBER(signal_id)
@@ -334,7 +334,7 @@
 #define SET_TRACK(track,mode)
 #define SET_POWER(track,onoff)
 #define SETLOCO(loco) 
-#define SETFREQ(loco,freq)
+#define SETFREQ(freq)
 #define SIGNAL(redpin,amberpin,greenpin) 
 #define SIGNALH(redpin,amberpin,greenpin) 
 #define SPEED(speed) 

EXRAILMacros.h

@@ -463,7 +463,7 @@ int RMFT2::onLCCLookup[RMFT2::countLCCLookup];
 
 #define ACTIVATE(addr,subaddr) OPCODE_DCCACTIVATE,V(addr<<3 | subaddr<<1 | 1),
 #define ACTIVATEL(addr) OPCODE_DCCACTIVATE,V((addr+3)<<1 | 1),
-#define AFTER(sensor_id) OPCODE_AT,V(sensor_id),OPCODE_AFTER,V(sensor_id),
+#define AFTER(sensor_id,timer...) OPCODE_AT,V(sensor_id),OPCODE_AFTER,V(sensor_id),OPCODE_PAD,V(#timer[0]?timer+0:500),
 #define AFTEROVERLOAD(track_id) OPCODE_AFTEROVERLOAD,V(TRACK_NUMBER_##track_id),
 #define ALIAS(name,value...) 
 #define AMBER(signal_id) OPCODE_AMBER,V(signal_id),
@@ -620,7 +620,7 @@ int RMFT2::onLCCLookup[RMFT2::countLCCLookup];
 #define SET_TRACK(track,mode)  OPCODE_SET_TRACK,V(TRACK_MODE_##mode  <<8 | TRACK_NUMBER_##track),
 #define SET_POWER(track,onoff) OPCODE_SET_POWER,V(TRACK_POWER_##onoff),OPCODE_PAD, V(TRACK_NUMBER_##track),
 #define SETLOCO(loco) OPCODE_SETLOCO,V(loco),
-#define SETFREQ(loco,freq) OPCODE_SETLOCO,V(loco), OPCODE_SETFREQ,V(freq),
+#define SETFREQ(freq) OPCODE_SETFREQ,V(freq),
 #define SIGNAL(redpin,amberpin,greenpin) 
 #define SIGNALH(redpin,amberpin,greenpin) 
 #define SPEED(speed) OPCODE_SPEED,V(speed),

IO_RocoDriver.h

@@ -0,0 +1,157 @@
+/*
+ *  © 2024, Chris Harlow. All rights reserved.
+ *
+ *  This file is part of EX-CommandStation
+ *
+ *  This is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 3 of the License, or
+ *  (at your option) any later version.
+ *
+ *  It is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
+*/
+
+/*
+* The IO_RocoDriver device driver uses a rotary encoder connected to vpins
+* to drive a loco.
+*  Loco id is selected by writeAnalog.
+*/
+
+#ifndef IO_ROCODRIVER_H
+#define IO_ROCODRIVER_H
+
+#include "DCC.h"
+#include "IODevice.h"
+#include "DIAG.h"
+
+const byte _DIR_CW = 0x10;  // Clockwise step
+const byte _DIR_CCW = 0x20;  // Counter-clockwise step
+
+const byte transition_table[5][4]= {
+    {0,1,3,0},            // 0: 00
+    {1,1,1,2 | _DIR_CW},  // 1: 00->01
+    {2,2,0,2},            // 2: 00->01->11
+    {3,3,3,4 | _DIR_CCW}, // 3: 00->10
+    {4,0,4,4}             // 4: 00->10->11
+};
+
+const byte _STATE_MASK = 0x07;
+const byte _DIR_MASK = 0x30;
+
+
+class RocoDriver : public IODevice {
+public:
+  
+  static void create(VPIN firstVpin, int dtPin, int clkPin, int clickPin, byte notch=10) {
+    if (checkNoOverlap(firstVpin)) new RocoDriver(firstVpin, dtPin,clkPin,clickPin,notch);
+  }
+
+private:
+  int _dtPin,_clkPin,_clickPin, _locoid, _notch,_prevpinstate; 
+  enum {xrSTOP,xrFWD,xrREV} _stopState;
+  byte _rocoState;  
+
+
+  // Constructor
+  RocoDriver(VPIN firstVpin, int dtPin, int clkPin, int clickPin, byte notch){
+    _firstVpin = firstVpin;
+    _nPins = 1;
+    _I2CAddress = 0;
+    _dtPin=dtPin;
+    _clkPin=clkPin;
+    _clickPin=clickPin;
+    _notch=notch;
+    _locoid=0;
+    _stopState=xrSTOP;
+    _rocoState=0; 
+    _prevpinstate=4; // not 01..11 
+    IODevice::configureInput(dtPin,true);
+    IODevice::configureInput(clkPin,true);
+    IODevice::configureInput(clickPin,true);
+    addDevice(this);
+    _display();
+  }
+
+  
+
+  void _loop(unsigned long currentMicros) override {
+    if (_locoid==0) return;  // not in use
+    
+    // Clicking down on the roco, stops the loco and sets the direction as unknown.
+  if (IODevice::read(_clickPin)) {
+    if (_stopState==xrSTOP) return; // debounced multiple stops
+    DCC::setThrottle(_locoid,1,DCC::getThrottleDirection(_locoid));
+    _stopState=xrSTOP;
+    DIAG(F("DRIVE %d STOP"),_locoid);
+    return; 
+  }
+
+  // read roco pins and detect state change 
+  byte pinstate = (IODevice::read(_dtPin) << 1) | IODevice::read(_clkPin);
+  if (pinstate==_prevpinstate) return;
+  _prevpinstate=pinstate;
+
+  _rocoState = transition_table[_rocoState & _STATE_MASK][pinstate];
+  if ((_rocoState & _DIR_MASK) == 0) return; // no value change 
+
+  int change=(_rocoState & _DIR_CW)?+1:-1;
+  // handle roco change -1 or +1 (clockwise)
+  
+  if (_stopState==xrSTOP) {
+      // first move after button press sets the direction. (clockwise=fwd)
+      _stopState=change>0?xrFWD:xrREV;
+    }
+
+    // when going fwd, clockwise increases speed. 
+    // but when reversing, anticlockwise increases speed.
+    // This is similar to a center-zero pot control but with
+    // the added safety that you cant panic-spin into the other
+    // direction.
+    if (_stopState==xrREV) change=-change; 
+    //  manage limits
+    int oldspeed=DCC::getThrottleSpeed(_locoid);
+    if (oldspeed==1)oldspeed=0; // break out of estop
+    int  newspeed=change>0 ?  (min((oldspeed+_notch),126)) : (max(0,(oldspeed-_notch)));
+    if (newspeed==1) newspeed=0; // normal decelereated stop. 
+    if (oldspeed!=newspeed) {
+        DIAG(F("DRIVE %d notch %S %d %S"),_locoid,
+             change>0?F("UP"):F("DOWN"),_notch,
+             _stopState==xrFWD?F("FWD"):F("REV"));
+        DCC::setThrottle(_locoid,newspeed,_stopState==xrFWD);
+        }
+}
+
+  // Selocoid as analog value to start drive
+  // use <z vpin locoid [notch]>
+  void _writeAnalogue(VPIN vpin, int value, uint8_t param1, uint16_t param2) override {  
+    (void) param2;
+    _locoid=value;
+    if (param1>0) _notch=param1;
+    _rocoState=0;
+    
+    // If loco is moving, we inherit direction from it.
+    _stopState=xrSTOP;
+    if (_locoid>0) {
+        auto speedbyte=DCC::getThrottleSpeedByte(_locoid);
+        if ((speedbyte & 0x7f) >1) {
+            // loco is moving
+            _stopState= (speedbyte & 0x80)?xrFWD:xrREV;
+        } 
+    }
+    _display();
+  }
+
+  
+  void _display() override {
+    DIAG(F("DRIVE vpin %d loco %d notch %d"),_firstVpin,_locoid,_notch);
+  }
+
+ };
+
+#endif

StringFormatter.cpp

@@ -139,6 +139,7 @@ void StringFormatter::send2(Print * stream,const FSH* format, va_list args) {
       case 'd': printPadded(stream,va_arg(args, int), formatWidth, formatLeft); break;
       case 'u': printPadded(stream,va_arg(args, unsigned int), formatWidth, formatLeft); break;
       case 'l': printPadded(stream,va_arg(args, long), formatWidth, formatLeft); break;
+      case 'L': stream->print(va_arg(args, unsigned long), DEC); break;
       case 'b': stream->print(va_arg(args, int), BIN); break;
       case 'o': stream->print(va_arg(args, int), OCT); break;
       case 'x': stream->print((unsigned int)va_arg(args, unsigned int), HEX); break;

version.h

@@ -3,7 +3,15 @@
 
 #include "StringFormatter.h"
 
-#define VERSION "5.2.65"
+#define VERSION "5.2.69"
+// 5.2.69 -  IO_RocoDriver. Direct drive train with rotary encoder hw.
+// 5.2.68 -  Revert function map to signed (from 5.2.66) to avoid
+//           incompatibilities with ED etc for F31 frequency flag.
+// 5.2.67 -  EXRAIL AFTER optional debounce time variable (default 500mS)
+//        -  AFTER(42) == AFTER(42,500) sets time sensor must 
+//        -  be continuously off.
+// 5.2.66 - <F cab DCFREQ 0..3>
+//        - EXRAIL SETFREQ drop loco param (breaking since 5.2.28)
 // 5.2.65 - Speedup Exrail SETFREQ 
 // 5.2.64 - Bugfix: <0 PROG> updated to undo JOIN 
 // 5.2.63 - Implement WIFI_LED for ESP32, ESPduino32 and EX-CSB1, that is turned on when STA mode connects or AP mode is up
@@ -12,7 +20,7 @@
 // 5.2.62 - Allow acks way longer than standard
 // 5.2.61 - Merg CBUS  ACON/ACOF/ONACON/ONACOF Adapter interface.
 //        - LCC Adapter interface throttled startup,
-//          (Breaking change woith Adapter base code)
+//          (Breaking change with Adapter base code)
 // 5.2.60 - Bugfix: Opcode AFTEROVERLOAD does not have an argument that is a pin and needs to be initialized
 //        - Remove inrush throttle after half good time so that we go to mode overload if problem persists
 // 5.2.59 - STM32 bugfix correct Serial1 definition for Nucleo-F401RE