DCCACK.cpp

@@ -351,7 +351,7 @@ void DCCACK::callback(int value) {
 
     switch (callbackState) {
       case AFTER_READ:
-         if (ackManagerRejoin && !autoPowerOff) {
+         if (ackManagerRejoin && autoPowerOff) {
                 progDriver->setPower(POWERMODE::OFF);
                 callbackStart=millis();
                 callbackState=WAITING_30;

DCCEXParser.cpp

@@ -25,79 +25,6 @@
  *  You should have received a copy of the GNU General Public License
  *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
  */
-
-/*
-List of single character OPCODEs in use for reference.
-
-When determining a new OPCODE for a new feature, refer to this list as the source of truth.
-
-Once a new OPCODE is decided upon, update this list.
-
-  Character, Usage
-  /, |EX-R| interactive commands
-  -, Remove from reminder table
-  =, |TM| configuration
-  !, Emergency stop
-  @, Reserved for future use - LCD messages to JMRI
-  #, Request number of supported cabs/locos; heartbeat
-  +, WiFi AT commands
-  ?, Reserved for future use
-  0, Track power off
-  1, Track power on
-  a, DCC accessory control
-  A,
-  b, Write CV bit on main
-  B, Write CV bit
-  c, Request current command
-  C,
-  d,
-  D, Diagnostic commands
-  e, Erase EEPROM
-  E, Store configuration in EEPROM
-  f, Loco decoder function control (deprecated)
-  F, Loco decoder function control
-  g,
-  G,
-  h,
-  H, Turnout state broadcast
-  i, Reserved for future use - Turntable object broadcast
-  I, Reserved for future use - Turntable object command and control
-  j, Throttle responses
-  J, Throttle queries
-  k, Reserved for future use - Potentially Railcom
-  K, Reserved for future use - Potentially Railcom
-  l, Loco speedbyte/function map broadcast
-  L,
-  m,
-  M, Write DCC packet
-  n,
-  N,
-  o,
-  O, Output broadcast
-  p, Broadcast power state
-  P, Write DCC packet
-  q, Sensor deactivated
-  Q, Sensor activated
-  r, Broadcast address read on programming track
-  R, Read CVs
-  s, Display status
-  S, Sensor configuration
-  t, Cab/loco update command
-  T, Turnout configuration/control
-  u, Reserved for user commands
-  U, Reserved for user commands
-  v,
-  V, Verify CVs
-  w, Write CV on main
-  W, Write CV
-  x,
-  X, Invalid command
-  y,
-  Y, Output broadcast
-  z,
-  Z, Output configuration/control
-*/
-
 #include "StringFormatter.h"
 #include "DCCEXParser.h"
 #include "DCC.h"
@@ -456,16 +383,12 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
 
 #ifndef DISABLE_PROG
     case 'w': // WRITE CV on MAIN <w CAB CV VALUE>
-      if (params != 3)
-	break;
-      DCC::writeCVByteMain(p[0], p[1], p[2]);
-      return;
+        DCC::writeCVByteMain(p[0], p[1], p[2]);
+        return;
 
     case 'b': // WRITE CV BIT ON MAIN <b CAB CV BIT VALUE>
-      if (params != 4)
-	break;
-      DCC::writeCVBitMain(p[0], p[1], p[2], p[3]);
-      return;
+        DCC::writeCVBitMain(p[0], p[1], p[2], p[3]);
+        return;
 #endif
 
     case 'M': // WRITE TRANSPARENT DCC PACKET MAIN <M REG X1 ... X9>
@@ -488,16 +411,14 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
         
 #ifndef DISABLE_PROG
     case 'W': // WRITE CV ON PROG <W CV VALUE CALLBACKNUM CALLBACKSUB>
-        if (!stashCallback(stream, p, ringStream))
-	    break;
+            if (!stashCallback(stream, p, ringStream))
+                break;
         if (params == 1) // <W id> Write new loco id (clearing consist and managing short/long)
             DCC::setLocoId(p[0],callback_Wloco);
         else if (params == 4)  // WRITE CV ON PROG <W CV VALUE [CALLBACKNUM] [CALLBACKSUB]>
             DCC::writeCVByte(p[0], p[1], callback_W4);
-        else if (params == 2)  // WRITE CV ON PROG <W CV VALUE>
+        else  // WRITE CV ON PROG <W CV VALUE>
             DCC::writeCVByte(p[0], p[1], callback_W);
-	else
-            break;
         return;
 
     case 'V': // VERIFY CV ON PROG <V CV VALUE> <V CV BIT 0|1>
@@ -517,11 +438,9 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
         }
         break;
 
-    case 'B': // WRITE CV BIT ON PROG  <B CV BIT VALUE CALLBACKNUM CALLBACKSUB> or <B CV BIT VALUE>
-        if (params != 3 && params != 5)
-	  break;
+    case 'B': // WRITE CV BIT ON PROG <B CV BIT VALUE CALLBACKNUM CALLBACKSUB>
         if (!stashCallback(stream, p, ringStream))
-	  break;
+            break;
         DCC::writeCVBit(p[0], p[1], p[2], callback_B);
         return;
 
@@ -651,12 +570,12 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
     case ' ': // < >
         StringFormatter::send(stream, F("\n"));
         return;
-#ifndef DISABLE_DIAG
+
     case 'D': // < >
         if (parseD(stream, params, p))
             return;
-        break;
-#endif
+        return;
+
     case '=': // <= Track manager control  >
         if (TrackManager::parseJ(stream, params, p))
             return;

EXRAIL2.cpp

@@ -2,7 +2,7 @@
  *  © 2021 Neil McKechnie
  *  © 2021-2023 Harald Barth
  *  © 2020-2023 Chris Harlow
- *  © 2022-2023 Colin Murdoch
+ *  © 2022 Colin Murdoch
  *  All rights reserved.
  *  
  *  This file is part of CommandStation-EX
@@ -99,7 +99,6 @@ LookList *  RMFT2::onClockLookup=NULL;
 #ifndef IO_NO_HAL
 LookList *  RMFT2::onRotateLookup=NULL;
 #endif
-LookList *  RMFT2::onOverloadLookup=NULL;
 
 #define GET_OPCODE GETHIGHFLASH(RMFT2::RouteCode,progCounter)
 #define SKIPOP progCounter+=3
@@ -184,7 +183,6 @@ LookList* RMFT2::LookListLoader(OPCODE op1, OPCODE op2, OPCODE op3) {
 #ifndef IO_NO_HAL
   onRotateLookup=LookListLoader(OPCODE_ONROTATE);
 #endif
-  onOverloadLookup=LookListLoader(OPCODE_ONOVERLOAD);
 
   // Second pass startup, define any turnouts or servos, set signals red
   // add sequences onRoutines to the lookups
@@ -204,7 +202,6 @@ LookList* RMFT2::LookListLoader(OPCODE op1, OPCODE op2, OPCODE op3) {
     case OPCODE_AT:
     case OPCODE_ATTIMEOUT2:
     case OPCODE_AFTER:
-    case OPCODE_AFTEROVERLOAD:
     case OPCODE_IF:
     case OPCODE_IFNOT: {
       int16_t pin = (int16_t)operand;
@@ -262,7 +259,7 @@ LookList* RMFT2::LookListLoader(OPCODE op1, OPCODE op2, OPCODE op3) {
     case OPCODE_EXTTTURNTABLE: {
       VPIN id=operand;
       VPIN pin=getOperand(progCounter,1);
-      int home=getOperand(progCounter,3);
+      int home=getOperand(progCounter,2);
       setTurntableHiddenState(EXTTTurntable::create(id,pin));
       Turntable *tto=Turntable::get(id);
       tto->addPosition(0,0,home);
@@ -740,17 +737,7 @@ void RMFT2::loop2() {
     }
     if (millis()-waitAfter < 500 ) return;
     break;
-
-  case OPCODE_AFTEROVERLOAD: // waits for the power to be turned back on - either by power routine or button
-    if (!TrackManager::isPowerOn(operand)) {
-      // reset timer to half a second and keep waiting
-      waitAfter=millis();
-      delayMe(50);
-      return;
-    }
-    if (millis()-waitAfter < 500 ) return;
-    break;
-
+    
   case OPCODE_LATCH:
     setFlag(operand,LATCH_FLAG);
     break;
@@ -1073,7 +1060,6 @@ void RMFT2::loop2() {
   case OPCODE_TTADDPOSITION:  // Turntable position definition ignored at runtime
   case OPCODE_ONROTATE:
 #endif
-  case OPCODE_ONOVERLOAD:
   
     break;
     
@@ -1235,16 +1221,6 @@ void RMFT2::clockEvent(int16_t clocktime, bool change) {
   }
 } 
 
-void RMFT2::powerEvent(int16_t track, bool overload) {
-  // Hunt for an ONOVERLOAD for this item
-  if (Diag::CMD)
-   DIAG(F("Looking for Power event on track : %c"), track);
-  if (overload) {
-    handleEvent(F("POWER"),onOverloadLookup,track);
-  }
-}
-
-
 void RMFT2::handleEvent(const FSH* reason,LookList* handlers, int16_t id) {
   int pc= handlers->find(id);
   if (pc<0) return;

EXRAIL2.h

@@ -1,7 +1,7 @@
 /*
  *  © 2021 Neil McKechnie
  *  © 2020-2022 Chris Harlow
- *  © 2022-2023 Colin Murdoch
+ *  © 2022 Colin Murdoch
  *  © 2023 Harald Barth
  *  All rights reserved.
  *  
@@ -36,8 +36,7 @@
 enum OPCODE : byte {OPCODE_THROW,OPCODE_CLOSE,
              OPCODE_FWD,OPCODE_REV,OPCODE_SPEED,OPCODE_INVERT_DIRECTION,
              OPCODE_RESERVE,OPCODE_FREE,
-             OPCODE_AT,OPCODE_AFTER,
-             OPCODE_AFTEROVERLOAD,OPCODE_AUTOSTART,
+             OPCODE_AT,OPCODE_AFTER,OPCODE_AUTOSTART,
              OPCODE_ATGTE,OPCODE_ATLT,
              OPCODE_ATTIMEOUT1,OPCODE_ATTIMEOUT2,
              OPCODE_LATCH,OPCODE_UNLATCH,OPCODE_SET,OPCODE_RESET,
@@ -68,7 +67,6 @@ enum OPCODE : byte {OPCODE_THROW,OPCODE_CLOSE,
              OPCODE_TTADDPOSITION,OPCODE_DCCTURNTABLE,OPCODE_EXTTTURNTABLE,
              OPCODE_ONROTATE,OPCODE_ROTATE,OPCODE_IFTTPOSITION,OPCODE_WAITFORTT,
 #endif
-             OPCODE_ONOVERLOAD,
 
              // OPcodes below this point are skip-nesting IF operations
              // placed here so that they may be skipped as a group
@@ -138,7 +136,6 @@ class LookList {
     static void changeEvent(int16_t id, bool change);
     static void clockEvent(int16_t clocktime, bool change);
     static void rotateEvent(int16_t id, bool change);
-    static void powerEvent(int16_t track, bool overload);
     static const int16_t SERVO_SIGNAL_FLAG=0x4000;
     static const int16_t ACTIVE_HIGH_SIGNAL_FLAG=0x2000;
     static const int16_t DCC_SIGNAL_FLAG=0x1000;
@@ -205,7 +202,6 @@ private:
 #ifndef IO_NO_HAL
    static LookList * onRotateLookup;
 #endif
-   static LookList * onOverloadLookup;
     
   // Local variables - exist for each instance/task 
     RMFT2 *next;   // loop chain 

EXRAIL2MacroReset.h

@@ -1,6 +1,6 @@
 /*
  *  © 2020-2022 Chris Harlow. All rights reserved.
- *  © 2022-2023 Colin Murdoch
+ *  © 2022 Colin Murdoch
  *  © 2023 Harald Barth
  *  
  *  This file is part of CommandStation-EX
@@ -27,7 +27,6 @@
 #undef ACTIVATE
 #undef ACTIVATEL
 #undef AFTER
-#undef AFTEROVERLOAD
 #undef ALIAS
 #undef AMBER
 #undef ANOUT
@@ -97,7 +96,6 @@
 #undef ONTIME
 #undef ONCLOCKTIME
 #undef ONCLOCKMINS
-#undef ONOVERLOAD
 #undef ONGREEN
 #undef ONRED
 #undef ONROTATE
@@ -164,7 +162,6 @@
 #define ACTIVATE(addr,subaddr)
 #define ACTIVATEL(addr)
 #define AFTER(sensor_id)
-#define AFTEROVERLOAD(track_id)
 #define ALIAS(name,value...)
 #define AMBER(signal_id)
 #define ANOUT(vpin,value,param1,param2)
@@ -192,7 +189,7 @@
 #define ENDTASK
 #define ESTOP 
 #define EXRAIL
-#define EXTT_TURNTABLE(id,vpin,i2c_address,home,description)
+#define EXTT_TURNTABLE(id,vpin,home,description)
 #define FADE(pin,value,ms)
 #define FOFF(func)
 #define FOLLOW(route) 
@@ -231,7 +228,6 @@
 #define ONTIME(value)
 #define ONCLOCKTIME(hours,mins)
 #define ONCLOCKMINS(mins)
-#define ONOVERLOAD(track_id)
 #define ONDEACTIVATE(addr,subaddr)
 #define ONDEACTIVATEL(linear) 
 #define ONCLOSE(turnout_id)

EXRAILMacros.h

@@ -1,7 +1,7 @@
 /*
  *  © 2021 Neil McKechnie
  *  © 2020-2022 Chris Harlow
- *  © 2022-2023 Colin Murdoch
+ *  © 2022 Colin Murdoch
  *  © 2023 Harald Barth
  *  All rights reserved.
  *  
@@ -69,13 +69,10 @@
 #define ALIAS(name,value...) const int name= 1##value##0 ==10 ? -__COUNTER__  : value##0/10; 
 #include "myAutomation.h"
 
-// Pass 1h Implements HAL macro by creating exrailHalSetup function
-// Also allows creating EXTurntable object
+// Pass 1h Implements HAL macro by creating exrailHalSetup function 
 #include "EXRAIL2MacroReset.h"
 #undef HAL
 #define HAL(haltype,params...)  haltype::create(params);
-#undef EXTT_TURNTABLE
-#define EXTT_TURNTABLE(id,vpin,i2c_address,home,description...) EXTurntable::create(vpin,1,i2c_address);
 void exrailHalSetup() {
    #include "myAutomation.h"
 }
@@ -197,7 +194,7 @@ const FSH * RMFT2::getTurnoutDescription(int16_t turnoutid) {
 #undef DCC_TURNTABLE
 #define DCC_TURNTABLE(id,home,description...) O_DESC(id,description)
 #undef EXTT_TURNTABLE
-#define EXTT_TURNTABLE(id,vpin,i2c_address,home,description...) O_DESC(id,description)
+#define EXTT_TURNTABLE(id,vpin,home,description...) O_DESC(id,description)
 
 const FSH * RMFT2::getTurntableDescription(int16_t turntableId) {
    switch (turntableId) {
@@ -286,7 +283,6 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define ACTIVATE(addr,subaddr) OPCODE_DCCACTIVATE,V(addr<<3 | subaddr<<1 | 1),
 #define ACTIVATEL(addr) OPCODE_DCCACTIVATE,V((addr+3)<<1 | 1),
 #define AFTER(sensor_id) OPCODE_AT,V(sensor_id),OPCODE_AFTER,V(sensor_id),
-#define AFTEROVERLOAD(track_id) OPCODE_AFTEROVERLOAD,V(TRACK_NUMBER_##track_id),
 #define ALIAS(name,value...) 
 #define AMBER(signal_id) OPCODE_AMBER,V(signal_id),
 #define ANOUT(vpin,value,param1,param2) OPCODE_SERVO,V(vpin),OPCODE_PAD,V(value),OPCODE_PAD,V(param1),OPCODE_PAD,V(param2),
@@ -317,7 +313,7 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define ESTOP OPCODE_SPEED,V(1), 
 #define EXRAIL
 #ifndef IO_NO_HAL
-#define EXTT_TURNTABLE(id,vpin,i2c_address,home,description...) OPCODE_EXTTTURNTABLE,V(id),OPCODE_PAD,V(vpin),OPCODE_PAD,V(i2c_address),OPCODE_PAD,V(home),
+#define EXTT_TURNTABLE(id,vpin,home,description...) OPCODE_EXTTTURNTABLE,V(id),OPCODE_PAD,V(vpin),OPCODE_PAD,V(home),
 #endif
 #define FADE(pin,value,ms) OPCODE_SERVO,V(pin),OPCODE_PAD,V(value),OPCODE_PAD,V(PCA9685::ProfileType::UseDuration|PCA9685::NoPowerOff),OPCODE_PAD,V(ms/100L),
 #define FOFF(func) OPCODE_FOFF,V(func),
@@ -360,7 +356,6 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define ONTIME(value) OPCODE_ONTIME,V(value),  
 #define ONCLOCKTIME(hours,mins) OPCODE_ONTIME,V((STRIP_ZERO(hours)*60)+STRIP_ZERO(mins)),
 #define ONCLOCKMINS(mins) ONCLOCKTIME(25,mins)
-#define ONOVERLOAD(track_id) OPCODE_ONOVERLOAD,V(TRACK_NUMBER_##track_id),
 #define ONDEACTIVATE(addr,subaddr) OPCODE_ONDEACTIVATE,V(addr<<2|subaddr),
 #define ONDEACTIVATEL(linear) OPCODE_ONDEACTIVATE,V(linear+3),
 #define ONGREEN(signal_id) OPCODE_ONGREEN,V(signal_id),

GITHUB_SHA.h

@@ -1 +1 @@
-#define GITHUB_SHA "devel-202308302157Z"
+#define GITHUB_SHA "devel-202308102205Z"

IO_PCA9555.h

@@ -30,8 +30,8 @@
  
 class PCA9555 : public GPIOBase<uint16_t> {
 public:
-  static void create(VPIN vpin, uint8_t nPins, I2CAddress i2cAddress, int interruptPin=-1) {
-    if (checkNoOverlap(vpin, nPins, i2cAddress)) new PCA9555(vpin,nPins, i2cAddress, interruptPin);
+  static void create(VPIN vpin, int nPins, uint8_t I2CAddress, int interruptPin=-1) {
+    new PCA9555(vpin, min(nPins,16), I2CAddress, interruptPin);
   }
   
   // Constructor

MotorDriver.cpp

@@ -4,7 +4,6 @@
  *  © 2021 Fred Decker
  *  © 2020-2023 Harald Barth
  *  © 2020-2021 Chris Harlow
- *  © 2023 Colin Murdoch
  *  All rights reserved.
  *  
  *  This file is part of CommandStation-EX
@@ -27,7 +26,6 @@
 #include "DCCWaveform.h"
 #include "DCCTimer.h"
 #include "DIAG.h"
-#include "EXRAIL2.h"
 
 unsigned long MotorDriver::globalOverloadStart = 0;
 
@@ -615,9 +613,7 @@ void MotorDriver::checkPowerOverload(bool useProgLimit, byte trackno) {
       // adjust next wait time
       power_sample_overload_wait *= 2;
       if (power_sample_overload_wait > POWER_SAMPLE_RETRY_MAX)
-	      power_sample_overload_wait = POWER_SAMPLE_RETRY_MAX;
-      DIAG(F("Calling EXRAIL"));
-      RMFT2::powerEvent(trackno, true); // Tell EXRAIL we have an overload
+	power_sample_overload_wait = POWER_SAMPLE_RETRY_MAX;
       // power on test
       DIAG(F("TRACK %c POWER RESTORE (after %4M)"), trackno + 'A', mslpc);
       setPower(POWERMODE::ALERT);

TrackManager.cpp

@@ -1,7 +1,6 @@
 /*
  *  © 2022 Chris Harlow
  *  © 2022 Harald Barth
- *  © 2023 Colin Murdoch
  *  All rights reserved.
  *  
  *  This file is part of DCC++EX
@@ -54,7 +53,7 @@ bool TrackManager::progTrackSyncMain=false;
 bool TrackManager::progTrackBoosted=false; 
 int16_t TrackManager::joinRelay=UNUSED_PIN;
 #ifdef ARDUINO_ARCH_ESP32
-byte TrackManager::tempProgTrack=MAX_TRACKS+1; // MAX_TRACKS+1 is the unused flag
+byte TrackManager::tempProgTrack=MAX_TRACKS+1;
 #endif
 
 #ifdef ANALOG_READ_INTERRUPT
@@ -506,12 +505,7 @@ void TrackManager::setJoin(bool joined) {
     }
   } else {
     if (tempProgTrack != MAX_TRACKS+1) {
-      // as setTrackMode with TRACK_MODE_PROG defaults to
-      // power off, we will take the current power state
-      // of our track and then preserve that state.
-      POWERMODE tPTmode = track[tempProgTrack]->getPower(); //get current power status of this track
       setTrackMode(tempProgTrack, TRACK_MODE_PROG);
-      track[tempProgTrack]->setPower(tPTmode);              //set track status as it was before
       tempProgTrack = MAX_TRACKS+1;
     }
   }
@@ -519,10 +513,3 @@ void TrackManager::setJoin(bool joined) {
   progTrackSyncMain=joined;
   if (joinRelay!=UNUSED_PIN) digitalWrite(joinRelay,joined?HIGH:LOW);
 }
-
-bool TrackManager::isPowerOn(byte t) {
-      if (track[t]->getPower()!=POWERMODE::ON) 
-	        return false;
-    return true;   
-  }
-

TrackManager.h

@@ -1,8 +1,6 @@
 /*
  *  © 2022 Chris Harlow
  *  © 2022 Harald Barth
- *  © 2023 Colin Murdoch
- * 
  *  All rights reserved.
  *  
  *  This file is part of CommandStation-EX
@@ -79,7 +77,6 @@ class TrackManager {
     static void reportCurrent(Print* stream);
     static void reportObsoleteCurrent(Print* stream); 
     static void streamTrackState(Print* stream, byte t);
-    static bool isPowerOn(byte t);
 
     static int16_t joinRelay;
     static bool progTrackSyncMain;  // true when prog track is a siding switched to main

defines.h

@@ -218,12 +218,8 @@
 // Define symbol IO_NO_HAL to reduce FLASH footprint when HAL features not required
 // The HAL is disabled by default on Nano and Uno platforms, because of limited flash space.
 // 
-#if defined(ARDUINO_AVR_NANO) || defined(ARDUINO_AVR_UNO)
-  #if defined(DISABLE_DIAG) && defined(DISABLE_EEPROM) && defined(DISABLE_PROG)
-    #warning you have sacrificed DIAG for HAL
-  #else
-    #define IO_NO_HAL
-  #endif
+#if defined(ARDUINO_AVR_NANO) || defined(ARDUINO_AVR_UNO) 
+#define IO_NO_HAL
 #endif
 
 #if __has_include ( "myAutomation.h")

myHal.cpp_example.txt

@@ -51,7 +51,7 @@ void halSetup() {
   // Create a 20x4 LCD display device as display number 2 
   // (line 0 is written by EX-RAIL 'SCREEN(2, 0, "text")').
 
-  // HALDisplay<LiquidCrystal>::create(2, 0x27, 20, 4);
+  // HALDisplay<LiquidCrystal>(2, 0x27, 20, 4);
 
 
   //=======================================================================

version.h

@@ -3,16 +3,8 @@
 
 #include "StringFormatter.h"
 
-#define VERSION "5.1.5"
-// 5.1.5  - Added turntable object and EXRAIL commands
-//        - <I ...>, <JO ...>, <JP ...> - turntable commands
-//        - DCC_TURNTABLE, EXTT_TURNTABLE, IFTTPOSITION, ONROTATE, ROTATE, ROTATE_DCC, TT_ADDPOSITION, WAITFORTT EXRAIL
-// 5.1.4  - Added ONOVERLOAD & AFTEROVERLOAD to EXRAIL
-// 5.1.3  - Make parser more fool proof
-// 5.1.2  - Bugfix: ESP32 30ms off time
-// 5.1.1  - Check bad AT firmware version
-//        - Update IO_PCA9555.h reflecting IO_MCP23017.h changes to support PCA9548 mux
-// 5.0.1  - Bugfix: execute 30ms off time before rejoin
+#define VERSION "5.0.1"
+// 5.0.1  - Check bad AT firmware version
 // 5.0.0  - Make 4.2.69 the 5.0.0 release
 // 4.2.69 - Bugfix: Make <!> work in DC mode
 // 4.2.68 - Rename track mode OFF to NONE