STM32 ADCee extensions

DCCTimer.h

@@ -125,8 +125,13 @@ private:
   // On platforms that scan, it is called from waveform ISR
   // only on a regular basis.
   static void scan();
+  #if defined (ARDUINO_ARCH_STM32)
+  // bit array of used pins (max 32)
+  static uint32_t usedpins;
+#else
   // bit array of used pins (max 16)
   static uint16_t usedpins;
+#endif
   static uint8_t highestPin;
   // cached analog values (malloc:ed to actual number of ADC channels)
   static int *analogvals;

DCCTimerSTM32.cpp

@@ -52,7 +52,7 @@ HardwareSerial Serial6(PA12, PA11);  // Rx=PA12, Tx=PA11 -- CN10 pins 12 and 14
 HardwareSerial Serial3(PC11, PC10);  // Rx=PC11, Tx=PC10 -- USART3 - F446RE
 HardwareSerial Serial5(PD2, PC12);  // Rx=PC7, Tx=PC6 -- UART5 - F446RE
 // On the F446RE, Serial4 and Serial6 also use pins we can't readily map while using the Arduino pins
-#elif defined(ARDUINO_NUCLEO_F413ZH) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)|| defined(ARDUINO_NUCLEO_F412ZG) 
+#elif defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F413ZH) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE) 
 // Nucleo-144 boards don't have Serial1 defined by default
 HardwareSerial Serial6(PG9, PG14);  // Rx=PG9, Tx=PG14 -- USART6
 // Serial3 is defined to use USART3 by default, but is in fact used as the diag console
@@ -235,22 +235,19 @@ void DCCTimer::reset() {
     while(true) {};
 }
 
-// TODO: may need to use uint32_t on STMF4xx variants with > 16 analog inputs!
+// Now we can handle more ADCs, maybe this works!
-#if defined(ARDUINO_NUCLEO_F446RE) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
+#define NUM_ADC_INPUTS NUM_ANALOG_INPUTS
-#warning STM32 board selected not fully supported - only use ADC1 inputs 0-15 for current sensing!
-#endif
-// For now, define the max of 16 ports - some variants have more, but this not **yet** supported
-#define NUM_ADC_INPUTS 16
-// #define NUM_ADC_INPUTS NUM_ANALOG_INPUTS
 
-uint16_t ADCee::usedpins = 0;
+uint32_t ADCee::usedpins = 0;         // Max of 32 ADC input channels!
-uint8_t ADCee::highestPin = 0;
+uint8_t ADCee::highestPin = 0;        // Highest pin to scan
-int * ADCee::analogvals = NULL;
+int * ADCee::analogvals = NULL;       // Array of analog values last captured
-uint32_t * analogchans = NULL;
+uint32_t * analogchans = NULL;        // Array of channel numbers to be scanned
-bool adc1configured = false;
+// bool adc1configured = false;
+ADC_TypeDef * * adcchans = NULL;      // Array to capture which ADC is each input channel on
 
-int16_t ADCee::ADCmax() {
+int16_t ADCee::ADCmax()
-  return 4095;
+{
+    return 4095;
 }
 
 int ADCee::init(uint8_t pin) {
@@ -261,11 +258,33 @@ int ADCee::init(uint8_t pin) {
     return -1024;   // some silly value as error
 
   uint32_t stmgpio = STM_PORT(stmpin); // converts to the GPIO port (16-bits per port group on STM32)
-  uint32_t adcchan =  STM_PIN_CHANNEL(pinmap_function(stmpin, PinMap_ADC)); // find ADC channel (only valid for ADC1!)
+  uint32_t adcchan =  STM_PIN_CHANNEL(pinmap_function(stmpin, PinMap_ADC)); // find ADC input channel
-  GPIO_TypeDef * gpioBase;
+  ADC_TypeDef *adc = (ADC_TypeDef *)pinmap_find_peripheral(stmpin, PinMap_ADC); // find which ADC this pin is on ADC1/2/3 etc.
+  int adcnum = 1;
+  if (adc == ADC1)
+    DIAG(F("ADCee::init(): found pin %d on ADC1"), pin);
+// Checking for ADC2 and ADC3 being defined helps cater for more variants later
+#if defined(ADC2)
+  else if (adc == ADC2)
+  {
+    DIAG(F("ADCee::init(): found pin %d on ADC2"), pin);
+    adcnum = 2;
+  }
+#endif
+#if defined(ADC3)
+  else if (adc == ADC3)
+  {
+    DIAG(F("ADCee::init(): found pin %d on ADC3"), pin);
+    adcnum = 3;
+  }
+#endif
+  else DIAG(F("ADCee::init(): found pin %d on unknown ADC!"), pin);
 
-  // Port config - find which port we're on and power it up
+    // Port config - find which port we're on and power it up
-  switch(stmgpio) {
+    GPIO_TypeDef *gpioBase;
+
+    switch (stmgpio)
+    {
     case 0x00:
         RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN; //Power up PORTA
         gpioBase = GPIOA;
@@ -278,6 +297,20 @@ int ADCee::init(uint8_t pin) {
         RCC->AHB1ENR |= RCC_AHB1ENR_GPIOCEN; //Power up PORTC
         gpioBase = GPIOC;
         break;
+    case 0x03:
+        RCC->AHB1ENR |= RCC_AHB1ENR_GPIODEN; //Power up PORTD
+        gpioBase = GPIOD;
+        break;
+    case 0x04:
+        RCC->AHB1ENR |= RCC_AHB1ENR_GPIOEEN; //Power up PORTE
+        gpioBase = GPIOE;
+        break;
+#if defined(GPIOF)
+    case 0x05:
+        RCC->AHB1ENR |= RCC_AHB1ENR_GPIOFEN; //Power up PORTF
+        gpioBase = GPIOF;
+        break;
+#endif
     default:
       return -1023; // some silly value as error
   }
@@ -293,31 +326,33 @@ int ADCee::init(uint8_t pin) {
   if (adcchan > 18)
     return -1022; // silly value as error
   if (adcchan < 10)
-    ADC1->SMPR2 |= (0b111 << (adcchan * 3)); // Channel sampling rate 480 cycles
+    adc->SMPR2 |= (0b111 << (adcchan * 3)); // Channel sampling rate 480 cycles
   else
-    ADC1->SMPR1 |= (0b111 << ((adcchan - 10) * 3)); // Channel sampling rate 480 cycles
+    adc->SMPR1 |= (0b111 << ((adcchan - 10) * 3)); // Channel sampling rate 480 cycles
 
   // Read the inital ADC value for this analog input
-  ADC1->SQR3 = adcchan;           // 1st conversion in regular sequence
+  adc->SQR3 = adcchan;           // 1st conversion in regular sequence
-  ADC1->CR2 |= (1 << 30);         // Start 1st conversion SWSTART
+  adc->CR2 |= ADC_CR2_SWSTART;   //(1 << 30);                     // Start 1st conversion SWSTART
-  while(!(ADC1->SR & (1 << 1)));  // Wait until conversion is complete
+  while(!(adc->SR & (1 << 1)));  // Wait until conversion is complete
-  value = ADC1->DR;               // Read value from register
+  value = adc->DR;               // Read value from register
 
   uint8_t id = pin - PNUM_ANALOG_BASE;
-  if (id > 15) { // today we have not enough bits in the mask to support more
+  // if (id > 15) { // today we have not enough bits in the mask to support more
-    return -1021;
+  //   return -1021;
-  }
+  // }
 
-  if (analogvals == NULL) {  // allocate analogvals and analogchans if this is the first invocation of init.
+  if (analogvals == NULL) {  // allocate analogvals, analogchans and adcchans if this is the first invocation of init
     analogvals = (int *)calloc(NUM_ADC_INPUTS+1, sizeof(int));
     analogchans = (uint32_t *)calloc(NUM_ADC_INPUTS+1, sizeof(uint32_t));
+    adcchans = (ADC_TypeDef **)calloc(NUM_ADC_INPUTS+1, sizeof(ADC_TypeDef));
   }
   analogvals[id] = value;     // Store sampled value
   analogchans[id] = adcchan;  // Keep track of which ADC channel is used for reading this pin
-  usedpins |= (1 << id);      // This pin is now ready
+  adcchans[id] = adc;         // Keep track of which ADC this channel is on
+  usedpins |= (1 << id);                // This pin is now ready
   if (id > highestPin) highestPin = id; // Store our highest pin in use
 
-  DIAG(F("ADCee::init(): value=%d, channel=%d, id=%d"), value, adcchan, id);
+  DIAG(F("ADCee::init(): value=%d, ADC%d: channel=%d, id=%d"), value, adcnum, adcchan, id);
 
   return value;
 }
@@ -344,13 +379,16 @@ void ADCee::scan() {
   static uint8_t id = 0;     // id and mask are the same thing but it is faster to
   static uint16_t mask = 1;  // increment and shift instead to calculate mask from id
   static bool waiting = false;
+  static ADC_TypeDef *adc;
 
-  if (waiting) {
+  adc = adcchans[id];
+  if (waiting)
+  {
     // look if we have a result
-    if (!(ADC1->SR & (1 << 1)))
+    if (!(adc->SR & (1 << 1)))
       return; // no result, continue to wait
     // found value
-    analogvals[id] = ADC1->DR;
+    analogvals[id] = adc->DR;
     // advance at least one track
 #ifdef DEBUG_ADC
     if (id == 1) TrackManager::track[1]->setBrake(0);
@@ -369,9 +407,10 @@ void ADCee::scan() {
     // look for a valid track to sample or until we are around
     while (true) {
       if (mask  & usedpins) {
-	// start new ADC aquire on id
+        // start new ADC aquire on id
-        ADC1->SQR3 = analogchans[id]; //1st conversion in regular sequence
+        adc = adcchans[id];
-        ADC1->CR2 |= (1 << 30); //Start 1st conversion SWSTART
+        adc->SQR3 = analogchans[id]; // 1st conversion in regular sequence
+        adc->CR2 |= (1 << 30);       // Start 1st conversion SWSTART
 #ifdef DEBUG_ADC
 	if (id == 1) TrackManager::track[1]->setBrake(1);
 #endif
@@ -392,19 +431,83 @@ void ADCee::scan() {
 void ADCee::begin() {
   noInterrupts();
   //ADC1 config sequence
-  // TODO: currently defaults to ADC1, may need more to handle other members of STM32F4xx family
+  RCC->APB2ENR |= RCC_APB2ENR_ADC1EN; // Enable ADC1 clock
-  RCC->APB2ENR |= (1 << 8); //Enable ADC1 clock (Bit8) 
   // Set ADC prescaler - DIV8 ~ 40ms, DIV6 ~ 30ms, DIV4 ~ 20ms, DIV2 ~ 11ms
   ADC->CCR = (0 << 16); // Set prescaler 0=DIV2, 1=DIV4, 2=DIV6, 3=DIV8
   ADC1->CR1 &= ~(1 << 8); //SCAN mode disabled (Bit8)
   ADC1->CR1 &= ~(3 << 24); //12bit resolution (Bit24,25 0b00)
   ADC1->SQR1 = (1 << 20); //Set number of conversions projected (L[3:0] 0b0001) -> 1 conversion
+  // Disable the DMA controller for ADC1
+  ADC1->CR2 &= ~ADC_CR2_DMA;
   ADC1->CR2 &= ~(1 << 1); //Single conversion
   ADC1->CR2 &= ~(1 << 11); //Right alignment of data bits bit12....bit0
   ADC1->SQR1 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
   ADC1->SQR2 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
   ADC1->SQR3 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
   ADC1->CR2 |= (1 << 0); // Switch on ADC1
+  // Wait for ADC1 to become ready (calibration complete)
+  while (!(ADC1->CR2 & ADC_CR2_ADON)) {
+  }
+#if defined(ADC2)
+  // Enable the ADC2 clock
+  RCC->APB2ENR |= RCC_APB2ENR_ADC2EN;
+
+  // Initialize ADC2
+  ADC2->CR1 = 0; // Disable all channels
+  ADC2->CR2 = 0; // Clear CR2 register
+
+  ADC2->CR1 &= ~(1 << 8); //SCAN mode disabled (Bit8)
+  ADC2->CR1 &= ~(3 << 24); //12bit resolution (Bit24,25 0b00)
+  ADC2->SQR1 = (1 << 20); //Set number of conversions projected (L[3:0] 0b0001) -> 1 conversion
+  ADC2->CR2 &= ~ADC_CR2_DMA;   // Disable the DMA controller for ADC3
+  ADC2->CR2 &= ~(1 << 1); //Single conversion
+  ADC2->CR2 &= ~(1 << 11); //Right alignment of data bits bit12....bit0
+  ADC2->SQR1 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+  ADC2->SQR2 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+  ADC2->SQR3 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+
+  // Enable the ADC
+  ADC2->CR2 |= ADC_CR2_ADON;
+
+  // Wait for ADC2 to become ready (calibration complete)
+  while (!(ADC2->CR2 & ADC_CR2_ADON)) {
+  }
+
+  // Perform ADC3 calibration (optional)
+  // ADC3->CR2 |= ADC_CR2_CAL;
+  // while (ADC3->CR2 & ADC_CR2_CAL) {
+  // }
+#endif
+#if defined(ADC3)
+  // Enable the ADC3 clock
+  RCC->APB2ENR |= RCC_APB2ENR_ADC3EN;
+
+  // Initialize ADC3
+  ADC3->CR1 = 0; // Disable all channels
+  ADC3->CR2 = 0; // Clear CR2 register
+
+  ADC3->CR1 &= ~(1 << 8); //SCAN mode disabled (Bit8)
+  ADC3->CR1 &= ~(3 << 24); //12bit resolution (Bit24,25 0b00)
+  ADC3->SQR1 = (1 << 20); //Set number of conversions projected (L[3:0] 0b0001) -> 1 conversion
+  ADC3->CR2 &= ~ADC_CR2_DMA;   // Disable the DMA controller for ADC3
+  ADC3->CR2 &= ~(1 << 1); //Single conversion
+  ADC3->CR2 &= ~(1 << 11); //Right alignment of data bits bit12....bit0
+  ADC3->SQR1 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+  ADC3->SQR2 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+  ADC3->SQR3 &= ~(0x3FFFFFFF); //Clear whole 1st 30bits in register
+
+  // Enable the ADC
+  ADC3->CR2 |= ADC_CR2_ADON;
+
+  // Wait for ADC3 to become ready (calibration complete)
+  while (!(ADC3->CR2 & ADC_CR2_ADON)) {
+  }
+
+  // Perform ADC3 calibration (optional)
+  // ADC3->CR2 |= ADC_CR2_CAL;
+  // while (ADC3->CR2 & ADC_CR2_CAL) {
+  // }
+#endif
   interrupts();
 }
 #endif

I2CManager_STM32.h

@@ -37,9 +37,11 @@
  *  I2C bus, or more than one I2C bus on the STM32 architecture 
  *****************************************************************************/
 #if defined(I2C_USE_INTERRUPTS) && defined(ARDUINO_ARCH_STM32)
-#if defined(ARDUINO_NUCLEO_F411RE) || defined(ARDUINO_NUCLEO_F446RE) || defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
+#if defined(ARDUINO_NUCLEO_F401RE) || defined(ARDUINO_NUCLEO_F411RE) || defined(ARDUINO_NUCLEO_F446RE) \
+    || defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F413ZH) \
+    || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
 // Assume I2C1 for now - default I2C bus on Nucleo-F411RE and likely all Nucleo-64
-// and Nucleo-144variants
+// and Nucleo-144 variants
 I2C_TypeDef *s = I2C1;
 
 // In init we will ask the STM32 HAL layer for the configured APB1 clock frequency in Hz

platformio.ini

@@ -31,7 +31,6 @@ include_dir = .
 [env]
 build_flags = -Wall -Wextra
 ; monitor_filters = time
-; lib_deps = adafruit/Adafruit ST7735 and ST7789 Library @ ^1.10.0
 
 [env:samd21-dev-usb]
 platform = atmelsam
@@ -60,7 +59,7 @@ framework = arduino
 lib_deps = ${env.lib_deps}
 monitor_speed = 115200
 monitor_echo = yes
-build_flags = -std=c++17 ; -DI2C_USE_WIRE  -DDIAG_LOOPTIMES -DDIAG_IO
+build_flags = -std=c++17
 
 [env:mega2560-debug]
 platform = atmelavr
@@ -72,7 +71,7 @@ lib_deps =
 	SPI
 monitor_speed = 115200
 monitor_echo = yes
-build_flags =  -DDIAG_IO=2 -DDIAG_LOOPTIMES
+build_flags = -DDIAG_IO=2 -DDIAG_LOOPTIMES
 
 [env:mega2560-no-HAL]
 platform = atmelavr
@@ -108,7 +107,7 @@ lib_deps =
 	SPI
 monitor_speed = 115200
 monitor_echo = yes
-build_flags =     ; -DDIAG_LOOPTIMES
+build_flags = 
 
 [env:mega328]
 platform = atmelavr
@@ -190,10 +189,75 @@ platform = ststm32
 board = nucleo_f446re
 framework = arduino
 lib_deps = ${env.lib_deps}
-build_flags = -std=c++17  -Os -g2 -Wunused-variable ; -DDIAG_LOOPTIMES ; -DDIAG_IO 
+build_flags = -std=c++17  -Os -g2 -Wunused-variable
 monitor_speed = 115200
 monitor_echo = yes
 
+; Experimental - no reason this should not work, but not
+; tested as yet
+;
+[env:Nucleo-F401RE]
+platform = ststm32
+board = nucleo_f401re
+framework = arduino
+lib_deps = ${env.lib_deps}
+build_flags = -std=c++17  -Os -g2 -Wunused-variable
+monitor_speed = 115200
+monitor_echo = yes
+
+; Commented out by default as the F13ZH has variant files
+; but NOT the nucleo_f413zh.json file which needs to be
+; installed before you can let PlatformIO see this
+;
+; [env:Nucleo-F413ZH]
+; platform = ststm32
+; board = nucleo_f413zh
+; framework = arduino
+; lib_deps = ${env.lib_deps}
+; build_flags = -std=c++17  -Os -g2 -Wunused-variable
+; monitor_speed = 115200
+; monitor_echo = yes
+
+; Commented out by default as the F446ZE needs variant files
+; installed before you can let PlatformIO see this
+;
+; [env:Nucleo-F446ZE]
+; platform = ststm32
+; board = nucleo_f446ze
+; framework = arduino
+; lib_deps = ${env.lib_deps}
+; build_flags = -std=c++17  -Os -g2 -Wunused-variable
+; monitor_speed = 115200
+; monitor_echo = yes
+
+; Commented out by default as the F412ZG needs variant files
+; installed before you can let PlatformIO see this
+;
+; [env:Nucleo-F412ZG]
+; platform = ststm32
+; board = blah_f412zg
+; framework = arduino
+; lib_deps = ${env.lib_deps}
+; build_flags = -std=c++17 -Os -g2 -Wunused-variable
+; monitor_speed = 115200
+; monitor_echo = yes
+; upload_protocol = stlink
+
+; Experimental - Ethernet work still in progress
+;
+; [env:Nucleo-F429ZI]
+; platform = ststm32
+; board = nucleo_f429zi
+; framework = arduino
+; lib_deps = ${env.lib_deps}
+; 			arduino-libraries/Ethernet @ ^2.0.1
+; 			stm32duino/STM32Ethernet @ ^1.3.0
+; 			stm32duino/STM32duino LwIP @ ^2.1.2
+; build_flags = -std=c++17 -Os -g2 -Wunused-variable
+; monitor_speed = 115200
+; monitor_echo = yes
+; upload_protocol = stlink
+
 [env:Teensy3_2]
 platform = teensy
 board = teensy31
@@ -233,4 +297,3 @@ framework = arduino
 build_flags = -std=c++17  -Os -g2
 lib_deps = ${env.lib_deps}
 lib_ignore =
-

version.h

@@ -3,7 +3,8 @@
 
 #include "StringFormatter.h"
 
-#define VERSION "5.1.7"
+#define VERSION "5.1.8"
+// 5.1.8  - STM32Fxx ADCee extension to support ADCs #2 and #3
 // 5.1.7  - Fix turntable broadcasts for non-movement activities and <JP> result
 // 5.1.6  - STM32F4xx native I2C driver added
 // 5.1.5  - Added turntable object and EXRAIL commands