/********************************************************************** config.h COPYRIGHT (c) 2020 Fred Decker The configuration file for DCC-EX Command Station **********************************************************************/ ///////////////////////////////////////////////////////////////////////////////////// // NOTE: Before connecting these boards and selecting one in this software // check the quick install guides!!! Some of these boards require a voltage // generating resitor on the current sense pin of the device. Failure to select // the correct resistor could damage the sense pin on your Arduino or destroy // the device. // // DEFINE MOTOR_SHIELD_TYPE BELOW ACCORDING TO THE FOLLOWING TABLE: // // STANDARD_MOTOR_SHIELD : Arduino Motor shield Rev3 based on the L298 with 18V 2A per channel // POLOLU_MOTOR_SHIELD : Pololu MC33926 Motor Driver (not recommended for prog track) // FUNDUMOTO_SHIELD : Fundumoto Shield, no current sensing (not recommended, no short protection) // FIREBOX_MK1 : The Firebox MK1 // FIREBOX_MK1S : The Firebox MK1S // | // +-----------------------v // #define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD ///////////////////////////////////////////////////////////////////////////////////// // // The IP port to talk to a WIFI or Ethernet shield. // #define IP_PORT 2560 ///////////////////////////////////////////////////////////////////////////////////// // // NOTE: Only supported on Arduino Mega // Set to false if you not even want it on the Arduino Mega // #define ENABLE_WIFI true ///////////////////////////////////////////////////////////////////////////////////// // // DEFINE WiFi Parameters (only in effect if WIFI is on) // // If DONT_TOUCH_WIFI_CONF is set, all WIFI config will be done with // the <+> commands and this sketch will not change anything over // AT commands and the other WIFI_* defines below do not have any effect. //#define DONT_TOUCH_WIFI_CONF // // WIFI_SSID is the network name IF you want to use your existing home network. // Do NOT change this if you want to use the WiFi in Access Point (AP) mode. // // If you do NOT set the WIFI_SSID and do NOT set the WIFI_PASSWORD, // then the WiFi chip will first try to connect to the previously // configured network and if that fails fall back to Access Point mode. // The SSID of the AP will be automatically set to DCCEX_*. // If you DO set the WIFI_SSID then the WiFi chip will try to connect // to that (home) network in station (client) mode. If a WIFI_PASSWORD // is set (recommended), that password will be used for AP mode. // The AP mode password must be at least 8 characters long. // // Your SSID may not conain ``"'' (double quote, ASCII 0x22). #define WIFI_SSID "Your network name" // // WIFI_PASSWORD is the network password for your home network or if // you want to change the password from default AP mode password // to the AP password you want. // Your password may not conain ``"'' (double quote, ASCII 0x22). #define WIFI_PASSWORD "Your network passwd" // // WIFI_HOSTNAME: You probably don't need to change this #define WIFI_HOSTNAME "dccex" // // WIFI_CHANNEL: #define WIFI_CHANNEL 1 // ///////////////////////////////////////////////////////////////////////////////////// // // Wifi connect timeout in milliseconds. Default is 14000 (14 seconds). You only need // to set this if you have an extremely slow Wifi router. // //#define WIFI_CONNECT_TIMEOUT 14000 ///////////////////////////////////////////////////////////////////////////////////// // // ENABLE_ETHERNET: Set to true if you have an Arduino Ethernet card (wired). This // is not for Wifi. You will then need the Arduino Ethernet library as well // //#define ENABLE_ETHERNET true ///////////////////////////////////////////////////////////////////////////////////// // // DEFINE STATIC IP ADDRESS *OR* COMMENT OUT TO USE DHCP // //#define IP_ADDRESS { 192, 168, 1, 200 } ///////////////////////////////////////////////////////////////////////////////////// // // DEFINE LCD SCREEN USAGE BY THE BASE STATION // // Note: This feature requires an I2C enabled LCD screen using a PCF8574 based chipset. // or one using a Hitachi HD44780. // OR an I2C Oled screen. // To enable, uncomment one of the lines below // define LCD_DRIVER for I2C LCD address 0x3f,16 cols, 2 rows // #define LCD_DRIVER 0x3F,16,2 //OR define OLED_DRIVER width,height in pixels (address auto detected) // This will not work on a UNO due to memory constraints // #define OLED_DRIVER 128,32 ///////////////////////////////////////////////////////////////////////////////////// // // Enable warning as memory gets depleted #define ENABLE_FREE_MEM_WARNING false