/**********************************************************************

Config.h
COPYRIGHT (c) 2013-2016 Gregg E. Berman
COPYRIGHT (c) 2020 Fred Decker

The configuration file for DCC++ EX Command Station

**********************************************************************/

/////////////////////////////////////////////////////////////////////////////////////
//  NOTE: Before connecting these boards and selecting one in this software
//        check the quick install guides!!! Some of these boards require a voltage
//        generating resitor on the current sense pin of the device. Failure to select
//        the correct resistor could damage the sense pin on your Arduino or destroy
//        the device.
//
// DEFINE MOTOR_SHIELD_TYPE ACCORDING TO THE FOLLOWING TABLE:
//
//  STANDARD_MOTOR_SHIELD = ARDUINO MOTOR SHIELD            (MAX 18V/2A  PER CHANNEL)  Arduino Motor shield Rev3 based on the L298
//  POLOLU_MOTOR_SHIELD = POLOLU MC33926 MOTOR SHIELD     (MAX 28V/2.5 PER CHANNEL)  Pololu MC33926 Motor Driver (shield or carrier)
//  FUNDUMOTO_SHIELD = FunduMoto Motor Shield                     
//  FIREBOX_MK1 = Firebox MK1                    
//  FIREBOX_MK1S = Firebox MK1S    


#define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD

/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE PROGRAM TRACK CURRENT LIMIT IN MILLIAMPS

#define TRIP_CURRENT_PROG 250


/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE NUMBER OF MAIN TRACK REGISTER

#define MAX_MAIN_REGISTERS 22

/////////////////////////////////////////////////////////////////////////////////////
//
// NOTE: Only the Mega currently supports WiFi since space is a constraint on the Uno
//       at this time. It may be implemented in the future.
//       
//       
//
// Enable Use of WiFI for the Command Station for DCC-EX communications

#define ENABLE_WIFI false

#if ENABLE_WIFI
	/////////////////////////////////////////////////////////////////////////////////////
	//
	// DEFINE WiFi Parameters
	//
    #define WIFI_SSID "Your network name"
    #define WIFI_PASSWORD "Your network passwd"
    #define WIFI_HOSTNAME ""
    #define WIFI_PORT 3252
    

	// This defines the speed at which the Arduino will communicate with the ESP8266 module.
	// When using the ESP8266 on an Uno it is recommended to use 9600, for Mega2560 the
	// higher speed can be used.  Set this based on your ESP8266 module configuration.
	// Common defaults are 9600 or 115200.
	#define WIFI_SERIAL_LINK_SPEED 115200
#endif

/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE STATIC IP ADDRESS *OR* COMMENT OUT TO USE DHCP
//

//#define IP_ADDRESS { 192, 168, 1, 200 }

/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE PORT TO USE FOR ETHERNET COMMUNICATIONS INTERFACE
//
// Uncomment to use Ethernet

// #define ETHERNET_PORT 2560

/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE MAC ADDRESS ARRAY FOR ETHERNET COMMUNICATIONS INTERFACE
//
// Uncomment to use with Ethernet Shields
//
// NOTE: This is not used with ESP8266 WiFi modules.

// #define MAC_ADDRESS {  0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xEF }

/////////////////////////////////////////////////////////////////////////////////////
//
// Allows using a pin as a trigger for a scope or analyzer so we can capture only
// the important parts of the data stream
//
// USE_TRIGGERPIN: Enable code that switches the trigger pin on and off at end
//                 of the preamble. This takes some clock cycles in the
//                 interrupt routine for the main track.
// USE_TRIGGERPIN_PER_BIT: As above but for every bit. This only makes sense
//                 if USE_TRIGGERPIN is set.
//
// The value of the TRIGGERPIN is defined in DCCppEX.h because it might
// be board specific
//
//#define USE_TRIGGERPIN
//#define USE_TRIGGERPIN_PER_BIT

/////////////////////////////////////////////////////////////////////////////////////
//
// Define only of you need the store to EEPROM feature. This takes RAM and
// you may need to use less MAX_MAIN_REGISTERS to compensate (at least on the UNO)

#define EESTORE

/////////////////////////////////////////////////////////////////////////////////////
//
// This shows the status and version at startup. This takes RAM. You can comment
// this line if you need to increase MAX_MAIN_REGISTERS(at least on the UNO)

#define SHOWCONFIG

/////////////////////////////////////////////////////////////////////////////////////
//
// This is different from the above config display which only shows one line at startup
// This defines a pin that when jumpered to ground before powering up the Arduinio, 
// will display more detailed settings for diagnostics. You must remove the jumper and
// restart the Arduino to return to normal operation

#define SHOW_CONFIG_DETAIL_PIN A2

/////////////////////////////////////////////////////////////////////////////////////
//
// PREAMBLE_MAIN: Length of the preamble on the main track. Per standard this should
//                be at least 14 bits but if some equipment wants to insert a RailCom
//                cutout this should be at least 16 bits.
// PERAMBLE_PROG: Length of the preamble on the programming track. Per standard this
//                should be at least 22 bits 

#define PREAMBLE_MAIN 16 // TODO: Finish configurable preamble code
#define PREAMBLE_PROG 22

/////////////////////////////////////////////////////////////////////////////////////
//
// DEFINE LCD SCREEN USAGE BY THE BASE STATION
//
// Note: This feature requires an I2C enabled LCD screen using a PCF8574 based chipset.
//       or one using a Hitachi  HD44780.
//
// To enable, uncomment the line below and make sure only the correct LIB_TYPE line
// is uncommented below to select the library used for your LCD backpack

//#define ENABLE_LCD

#ifdef ENABLE_LCD
    #define LIB_TYPE_PCF8574
	//#define LIB_TYPE_I2C
	// This defines the I2C address for the LCD device
	#define LCD_ADDRESS 0x27 //common defaults are 0x27 and 0x3F

	// This defines the number of columns the LCD device has
	#define LCD_COLUMNS 16

	// This defines the number of lines the LCD device has
	#define LCD_LINES 2
#endif


/////////////////////////////////////////////////////////////////////////////////////
//
// Enable custom command filtering
#define ENABLE_CUSTOM_FILTER false

/////////////////////////////////////////////////////////////////////////////////////
//
// Enable custom command filtering
#define ENABLE_CUSTOM_CALLBACK false

/////////////////////////////////////////////////////////////////////////////////////
//
// Enable custom command filtering
#define ENABLE_FREE_MEM_WARNING false