#include #include "Hardware.h" #include "DCCWaveform.h" #include "DIAG.h" DCCWaveform DCCWaveform::mainTrack(PREAMBLE_BITS_MAIN, true, (int)(MAIN_MAX_MILLIAMPS / MAIN_SENSE_FACTOR)); DCCWaveform DCCWaveform::progTrack(PREAMBLE_BITS_PROG, false, (int)(PROG_MAX_MILLIAMPS / PROG_SENSE_FACTOR)); const int ACK_MIN_PULSE_RAW=65 / PROG_SENSE_FACTOR; void DCCWaveform::begin() { Hardware::init(); Hardware::setCallback(58, interruptHandler); mainTrack.beginTrack(); progTrack.beginTrack(); } void DCCWaveform::loop() { mainTrack.checkPowerOverload(); progTrack.checkPowerOverload(); } // static // void DCCWaveform::interruptHandler() { // call the timer edge sensitive actions for progtrack and maintrack bool mainCall2 = mainTrack.interrupt1(); bool progCall2 = progTrack.interrupt1(); // call (if necessary) the procs to get the current bits // these must complete within 50microsecs of the interrupt // but they are only called ONCE PER BIT TRANSMITTED // after the rising edge of the signal if (mainCall2) mainTrack.interrupt2(); if (progCall2) progTrack.interrupt2(); } // An instance of this class handles the DCC transmissions for one track. (main or prog) // Interrupts are marshalled via the statics. // A track has a current transmit buffer, and a pending buffer. // When the current buffer is exhausted, either the pending buffer (if there is one waiting) or an idle buffer. // This bitmask has 9 entries as each byte is trasmitted as a zero + 8 bits. const byte bitMask[] = {0x00, 0x80, 0x40, 0x20, 0x10, 0x08, 0x04, 0x02, 0x01}; DCCWaveform::DCCWaveform( byte preambleBits, bool isMain, int rawCurrentTrip) { // establish appropriate pins rawCurrentTripValue=rawCurrentTrip; isMainTrack = isMain; packetPending = false; memcpy(transmitPacket, idlePacket, sizeof(idlePacket)); state = 0; // The +1 below is to allow the preamble generator to create the stop bit // fpr the previous packet. requiredPreambles = preambleBits+1; bytes_sent = 0; bits_sent = 0; sampleDelay = 0; lastSampleTaken = millis(); ackPending=false; } void DCCWaveform::beginTrack() { setPowerMode(POWERMODE::ON); } POWERMODE DCCWaveform::getPowerMode() { return powerMode; } void DCCWaveform::setPowerMode(POWERMODE mode) { powerMode = mode; Hardware::setPower(isMainTrack, mode == POWERMODE::ON); if (mode == POWERMODE::ON) delay(200); } void DCCWaveform::checkPowerOverload() { if (millis() - lastSampleTaken < sampleDelay) return; lastSampleTaken = millis(); switch (powerMode) { case POWERMODE::OFF: sampleDelay = POWER_SAMPLE_OFF_WAIT; break; case POWERMODE::ON: // Check current lastCurrent = Hardware::getCurrentRaw(isMainTrack); if (lastCurrent <= rawCurrentTripValue) sampleDelay = POWER_SAMPLE_ON_WAIT; else { setPowerMode(POWERMODE::OVERLOAD); unsigned int mA=Hardware::getCurrentMilliamps(isMainTrack,lastCurrent); unsigned int maxmA=Hardware::getCurrentMilliamps(isMainTrack,rawCurrentTripValue); DIAG(F("\n*** %S TRACK POWER OVERLOAD current=%d max=%d ***\n"), isMainTrack ? F("MAIN") : F("PROG"), mA, maxmA); sampleDelay = POWER_SAMPLE_OVERLOAD_WAIT; } break; case POWERMODE::OVERLOAD: // Try setting it back on after the OVERLOAD_WAIT setPowerMode(POWERMODE::ON); sampleDelay = POWER_SAMPLE_ON_WAIT; break; default: sampleDelay = 999; // cant get here..meaningless statement to avoid compiler warning. } } // process time-edge sensitive part of interrupt // return true if second level required bool DCCWaveform::interrupt1() { // NOTE: this must consume transmission buffers even if the power is off // otherwise can cause hangs in main loop waiting for the pendingBuffer. switch (state) { case 0: // start of bit transmission Hardware::setSignal(isMainTrack, HIGH); state = 1; return true; // must call interrupt2 to set currentBit case 1: // 58us after case 0 if (currentBit) { Hardware::setSignal(isMainTrack, LOW); state = 0; } else state = 2; break; case 2: // 116us after case 0 Hardware::setSignal(isMainTrack, LOW); state = 3; break; case 3: // finished sending zero bit state = 0; break; } // ACK check is prog track only and will only be checked if // this is not case(0) which needs relatively expensive packet change code to be called. if (ackPending) checkAck(); return false; } void DCCWaveform::interrupt2() { // set currentBit to be the next bit to be sent. if (remainingPreambles > 0 ) { currentBit = true; remainingPreambles--; return; } // beware OF 9-BIT MASK generating a zero to start each byte currentBit = transmitPacket[bytes_sent] & bitMask[bits_sent]; bits_sent++; // If this is the last bit of a byte, prepare for the next byte if (bits_sent == 9) { // zero followed by 8 bits of a byte //end of Byte bits_sent = 0; bytes_sent++; // if this is the last byte, prepere for next packet if (bytes_sent >= transmitLength) { // end of transmission buffer... repeat or switch to next message bytes_sent = 0; remainingPreambles = requiredPreambles; if (transmitRepeats > 0) { transmitRepeats--; } else if (packetPending) { // Copy pending packet to transmit packet for (int b = 0; b < pendingLength; b++) transmitPacket[b] = pendingPacket[b]; transmitLength = pendingLength; transmitRepeats = pendingRepeats; packetPending = false; sentResetsSincePacket=0; } else { // Fortunately reset and idle packets are the same length memcpy( transmitPacket, isMainTrack ? idlePacket : resetPacket, sizeof(idlePacket)); transmitLength = sizeof(idlePacket); transmitRepeats = 0; if (sentResetsSincePacket<250) sentResetsSincePacket++; } } } } // Wait until there is no packet pending, then make this pending void DCCWaveform::schedulePacket(const byte buffer[], byte byteCount, byte repeats) { if (byteCount >= MAX_PACKET_SIZE) return; // allow for chksum while (packetPending); byte checksum = 0; for (int b = 0; b < byteCount; b++) { checksum ^= buffer[b]; pendingPacket[b] = buffer[b]; } pendingPacket[byteCount] = checksum; pendingLength = byteCount + 1; pendingRepeats = repeats; packetPending = true; sentResetsSincePacket=0; } int DCCWaveform::getLastCurrent() { return lastCurrent; } // Operations applicable to PROG track ONLY. // (yes I know I could have subclassed the main track but...) void DCCWaveform::setAckBaseline(bool debug) { if (isMainTrack) return; ackThreshold=Hardware::getCurrentRaw(false) + ACK_MIN_PULSE_RAW; if (debug) DIAG(F("\nACK-BASELINE %d/%dmA"),ackThreshold,Hardware::getCurrentMilliamps(false,ackThreshold)); } void DCCWaveform::setAckPending(bool debug) { if (isMainTrack) return; (void)debug; ackMaxCurrent=0; ackPulseStart=0; ackPulseDuration=0; ackDetected=false; ackCheckStart=millis(); ackPending=true; // interrupt routines will now take note } byte DCCWaveform::getAck(bool debug) { if (ackPending) return (2); // still waiting if (debug) DIAG(F("\nACK-%S after %dmS max=%d/%dmA pulse=%duS"),ackDetected?F("OK"):F("FAIL"), ackCheckDuration, ackMaxCurrent,Hardware::getCurrentMilliamps(false,ackMaxCurrent), ackPulseDuration); if (ackDetected) return (1); // Yes we had an ack return(0); // pending set off but not detected means no ACK. } void DCCWaveform::checkAck() { // This function operates in interrupt() time so must be fast and can't DIAG if (sentResetsSincePacket > 6) { //ACK timeout ackCheckDuration=millis()-ackCheckStart; ackPending = false; return; } lastCurrent=Hardware::getCurrentRaw(false); if (lastCurrent > ackMaxCurrent) ackMaxCurrent=lastCurrent; // An ACK is a pulse lasting between 4.5 and 8.5 mSecs (refer @haba) if (lastCurrent>ackThreshold) { if (ackPulseStart==0) ackPulseStart=micros(); // leading edge of pulse detected return; } // not in pulse if (ackPulseStart==0) return; // keep waiting for leading edge // detected trailing edge of pulse ackPulseDuration=micros()-ackPulseStart; if (ackPulseDuration>1000 && ackPulseDuration<9000) { ackCheckDuration=millis()-ackCheckStart; ackDetected=true; ackPending=false; transmitRepeats=0; // shortcut remaining repeat packets return; // we have a genuine ACK result } ackPulseStart=0; // We have detected a too-short or too-long pulse so ignore and wait for next leading edge }