/* * © 2022-2023 Paul M Antoine * © 2021 Mike S * © 2021 Fred Decker * © 2020-2023 Harald Barth * © 2020-2021 Chris Harlow * All rights reserved. * * This file is part of CommandStation-EX * * This is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * It is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with CommandStation. If not, see . */ #include #include "MotorDriver.h" #include "DCCWaveform.h" #include "DCCTimer.h" #include "DIAG.h" unsigned long MotorDriver::globalOverloadStart = 0; volatile portreg_t shadowPORTA; volatile portreg_t shadowPORTB; volatile portreg_t shadowPORTC; MotorDriver::MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, int16_t brake_pin, byte current_pin, float sense_factor, unsigned int trip_milliamps, int16_t fault_pin) { const FSH * warnString = F("** WARNING **"); invertPower=power_pin < 0; if (invertPower) { powerPin = 0-power_pin; IODevice::write(powerPin,HIGH);// set to OUTPUT and off } else { powerPin = power_pin; IODevice::write(powerPin,LOW);// set to OUTPUT and off } signalPin=signal_pin; getFastPin(F("SIG"),signalPin,fastSignalPin); pinMode(signalPin, OUTPUT); fastSignalPin.shadowinout = NULL; if (HAVE_PORTA(fastSignalPin.inout == &PORTA)) { DIAG(F("Found PORTA pin %d"),signalPin); fastSignalPin.shadowinout = fastSignalPin.inout; fastSignalPin.inout = &shadowPORTA; } if (HAVE_PORTB(fastSignalPin.inout == &PORTB)) { DIAG(F("Found PORTB pin %d"),signalPin); fastSignalPin.shadowinout = fastSignalPin.inout; fastSignalPin.inout = &shadowPORTB; } if (HAVE_PORTC(fastSignalPin.inout == &PORTC)) { DIAG(F("Found PORTC pin %d"),signalPin); fastSignalPin.shadowinout = fastSignalPin.inout; fastSignalPin.inout = &shadowPORTC; } signalPin2=signal_pin2; if (signalPin2!=UNUSED_PIN) { dualSignal=true; getFastPin(F("SIG2"),signalPin2,fastSignalPin2); pinMode(signalPin2, OUTPUT); fastSignalPin2.shadowinout = NULL; if (HAVE_PORTA(fastSignalPin2.inout == &PORTA)) { DIAG(F("Found PORTA pin %d"),signalPin2); fastSignalPin2.shadowinout = fastSignalPin2.inout; fastSignalPin2.inout = &shadowPORTA; } if (HAVE_PORTB(fastSignalPin2.inout == &PORTB)) { DIAG(F("Found PORTB pin %d"),signalPin2); fastSignalPin2.shadowinout = fastSignalPin2.inout; fastSignalPin2.inout = &shadowPORTB; } if (HAVE_PORTC(fastSignalPin2.inout == &PORTC)) { DIAG(F("Found PORTC pin %d"),signalPin2); fastSignalPin2.shadowinout = fastSignalPin2.inout; fastSignalPin2.inout = &shadowPORTC; } } else dualSignal=false; if (brake_pin!=UNUSED_PIN){ invertBrake=brake_pin < 0; if (invertBrake) brake_pin = 0-brake_pin; if (brake_pin > MAX_PIN) DIAG(F("%S Brake pin %d > %d"), warnString, brake_pin, MAX_PIN); brakePin=(byte)brake_pin; getFastPin(F("BRAKE"),brakePin,fastBrakePin); // if brake is used for railcom cutout we need to do PORTX register trick here as well pinMode(brakePin, OUTPUT); setBrake(true); // start with brake on in case we hace DC stuff going on } else { brakePin=UNUSED_PIN; } currentPin=current_pin; if (currentPin!=UNUSED_PIN) { int ret = ADCee::init(currentPin); if (ret < -1010) { // XXX give value a name later DIAG(F("ADCee::init error %d, disable current pin %d"), ret, currentPin); currentPin = UNUSED_PIN; } } senseOffset=0; // value can not be obtained until waveform is activated if (fault_pin != UNUSED_PIN) { invertFault=fault_pin < 0; if (invertFault) fault_pin = 0-fault_pin; if (fault_pin > MAX_PIN) DIAG(F("%S Fault pin %d > %d"), warnString, fault_pin, MAX_PIN); faultPin=(byte)fault_pin; DIAG(F("Fault pin = %d invert %d"), faultPin, invertFault); getFastPin(F("FAULT"),faultPin, 1 /*input*/, fastFaultPin); pinMode(faultPin, INPUT); } else { faultPin=UNUSED_PIN; } // This conversion performed at compile time so the remainder of the code never needs // float calculations or libraray code. senseFactorInternal=sense_factor * senseScale; tripMilliamps=trip_milliamps; #ifdef MAX_CURRENT if (MAX_CURRENT > 0 && MAX_CURRENT < tripMilliamps) tripMilliamps = MAX_CURRENT; #endif rawCurrentTripValue=mA2raw(tripMilliamps); if (rawCurrentTripValue + senseOffset > ADCee::ADCmax()) { // This would mean that the values obtained from the ADC never // can reach the trip value. So independent of the current, the // short circuit protection would never trip. So we adjust the // trip value so that it is tiggered when the ADC reports it's // maximum value instead. // DIAG(F("Changing short detection value from %d to %d mA"), // raw2mA(rawCurrentTripValue), raw2mA(ADCee::ADCmax()-senseOffset)); rawCurrentTripValue=ADCee::ADCmax()-senseOffset; } if (currentPin==UNUSED_PIN) DIAG(F("%S No current or short detection"), warnString); else { DIAG(F("Pin %d Max %dmA (%d)"), currentPin, raw2mA(rawCurrentTripValue), rawCurrentTripValue); // self testing diagnostic for the non-float converters... may be removed when happy // DIAG(F("senseFactorInternal=%d raw2mA(1000)=%d mA2Raw(1000)=%d"), // senseFactorInternal, raw2mA(1000),mA2raw(1000)); } progTripValue = mA2raw(TRIP_CURRENT_PROG); } bool MotorDriver::isPWMCapable() { return (!dualSignal) && DCCTimer::isPWMPin(signalPin); } void MotorDriver::setPower(POWERMODE mode) { if (powerMode == mode) return; bool on=mode==POWERMODE::ON; if (on) { // when switching a track On, we need to check the crrentOffset with the pin OFF if (powerMode==POWERMODE::OFF && currentPin!=UNUSED_PIN) { senseOffset = ADCee::read(currentPin); DIAG(F("Track %c sensOffset=%d"),trackLetter,senseOffset); } IODevice::write(powerPin,invertPower ? LOW : HIGH); if (isProgTrack) DCCWaveform::progTrack.clearResets(); } else { IODevice::write(powerPin,invertPower ? HIGH : LOW); } powerMode=mode; } // setBrake applies brake if on == true. So to get // voltage from the motor bride one needs to do a // setBrake(false). // If the brakePin is negative that means the sense // of the brake pin on the motor bridge is inverted // (HIGH == release brake) and setBrake does // compensate for that. // void MotorDriver::setBrake(bool on, bool interruptContext) { if (brakePin == UNUSED_PIN) return; if (!interruptContext) {noInterrupts();} if (on ^ invertBrake) setHIGH(fastBrakePin); else setLOW(fastBrakePin); if (!interruptContext) {interrupts();} } bool MotorDriver::canMeasureCurrent() { return currentPin!=UNUSED_PIN; } /* * Return the current reading as pin reading 0 to 1023. If the fault * pin is activated return a negative current to show active fault pin. * As there is no -0, cheat a little and return -1 in that case. * * senseOffset handles the case where a shield returns values above or below * a central value depending on direction. * * Bool fromISR should be adjusted dependent how function is called */ int MotorDriver::getCurrentRaw(bool fromISR) { (void)fromISR; if (currentPin==UNUSED_PIN) return 0; int current; current = ADCee::read(currentPin, fromISR); // here one can diag raw value // if (fromISR == false) DIAG(F("%c: %d"), trackLetter, current); current = current-senseOffset; // adjust with offset if (current<0) current=0-current; // current >= 0 here, we use negative current as fault pin flag if ((faultPin != UNUSED_PIN) && powerPin) { if (invertFault ? isHIGH(fastFaultPin) : isLOW(fastFaultPin)) return (current == 0 ? -1 : -current); } return current; } #ifdef ANALOG_READ_INTERRUPT /* * This should only be called in interrupt context * Copies current value from HW to cached value in * Motordriver. */ #pragma GCC push_options #pragma GCC optimize ("-O3") bool MotorDriver::sampleCurrentFromHW() { byte low, high; //if (!bit_is_set(ADCSRA, ADIF)) if (bit_is_set(ADCSRA, ADSC)) return false; // if ((ADMUX & mask) != (currentPin - A0)) // return false; low = ADCL; //must read low before high high = ADCH; bitSet(ADCSRA, ADIF); sampleCurrent = (high << 8) | low; sampleCurrentTimestamp = millis(); return true; } void MotorDriver::startCurrentFromHW() { #if defined(ARDUINO_AVR_MEGA) || defined(ARDUINO_AVR_MEGA2560) const byte mask = 7; #else const byte mask = 31; #endif ADMUX=(1< 2) { if (tSpeed <= 58) { f = taurustones[ (tSpeed-2)/2 ] ; } } DCCTimer::DCCEXanalogWriteFrequency(brakePin, f); // set DC PWM frequency to 100Hz XXX May move to setup } #endif if (tSpeed <= 1) brake = 255; else if (tSpeed >= 127) brake = 0; else brake = 2 * (128-tSpeed); if (invertBrake) brake=255-brake; #if defined(ARDUINO_ARCH_ESP32) DCCTimer::DCCEXanalogWrite(brakePin,brake); #else analogWrite(brakePin,brake); #endif //DIAG(F("DCSignal %d"), speedcode); if (HAVE_PORTA(fastSignalPin.shadowinout == &PORTA)) { noInterrupts(); HAVE_PORTA(shadowPORTA=PORTA); setSignal(tDir); HAVE_PORTA(PORTA=shadowPORTA); interrupts(); } else if (HAVE_PORTB(fastSignalPin.shadowinout == &PORTB)) { noInterrupts(); HAVE_PORTB(shadowPORTB=PORTB); setSignal(tDir); HAVE_PORTB(PORTB=shadowPORTB); interrupts(); } else if (HAVE_PORTC(fastSignalPin.shadowinout == &PORTC)) { noInterrupts(); HAVE_PORTC(shadowPORTC=PORTC); setSignal(tDir); HAVE_PORTC(PORTC=shadowPORTC); interrupts(); } else { noInterrupts(); setSignal(tDir); interrupts(); } } unsigned int MotorDriver::raw2mA( int raw) { //DIAG(F("%d = %d * %d / %d"), (int32_t)raw * senseFactorInternal / senseScale, raw, senseFactorInternal, senseScale); return (int32_t)raw * senseFactorInternal / senseScale; } unsigned int MotorDriver::mA2raw( unsigned int mA) { //DIAG(F("%d = %d * %d / %d"), (int32_t)mA * senseScale / senseFactorInternal, mA, senseScale, senseFactorInternal); return (int32_t)mA * senseScale / senseFactorInternal; } void MotorDriver::getFastPin(const FSH* type,int pin, bool input, FASTPIN & result) { // DIAG(F("MotorDriver %S Pin=%d,"),type,pin); (void) type; // avoid compiler warning if diag not used above. #if defined(ARDUINO_ARCH_SAMD) PortGroup *port = digitalPinToPort(pin); #elif defined(ARDUINO_ARCH_STM32) GPIO_TypeDef *port = digitalPinToPort(pin); #else uint8_t port = digitalPinToPort(pin); #endif if (input) result.inout = portInputRegister(port); else result.inout = portOutputRegister(port); result.maskHIGH = digitalPinToBitMask(pin); result.maskLOW = ~result.maskHIGH; // DIAG(F(" port=0x%x, inoutpin=0x%x, isinput=%d, mask=0x%x"),port, result.inout,input,result.maskHIGH); } void MotorDriver::checkPowerOverload(bool useProgLimit, byte trackno) { int tripValue= useProgLimit?progTripValue:getRawCurrentTripValue(); switch (powerMode) { case POWERMODE::OFF: if (overloadNow) { // reset overload condition as we have just turned off power // DIAG(F("OVERLOAD POFF OFF")); overloadNow=false; setLastPowerChange(); } if (microsSinceLastPowerChange() > POWER_SAMPLE_ALL_GOOD) { power_sample_overload_wait = POWER_SAMPLE_OVERLOAD_WAIT; } break; case POWERMODE::ON: // Check current lastCurrent=getCurrentRaw(); if (lastCurrent < 0) { // We have a fault pin condition to take care of if (!overloadNow) { // turn on overload condition as fault pin has gone active // DIAG(F("OVERLOAD FPIN ON")); overloadNow=true; setLastPowerChangeOverload(); } lastCurrent = -lastCurrent; { if (lastCurrent < tripValue) { if (power_sample_overload_wait <= (POWER_SAMPLE_OVERLOAD_WAIT * 10) && // almost virgin microsSinceLastPowerChange() < POWER_SAMPLE_IGNORE_FAULT_LOW) { // Ignore 50ms fault pin if no current DIAG(F("TRACK %c FAULT PIN (50ms ignore)"), trackno + 'A'); break; } lastCurrent = tripValue; // exaggerate so condition below (*) is true } else { if (power_sample_overload_wait <= POWER_SAMPLE_OVERLOAD_WAIT && // virgin microsSinceLastPowerChange() < POWER_SAMPLE_IGNORE_FAULT_HIGH) { // Ignore 5ms fault pin if we see current DIAG(F("TRACK %c FAULT PIN (5ms ignore)"), trackno + 'A'); break; } } DIAG(F("TRACK %c FAULT PIN"), trackno + 'A'); } } // // // // above we looked at fault pin, below we look at current // // // if (lastCurrent < tripValue) { // see above (*) if (overloadNow) { // current is below trip value, turn off overload condition // DIAG(F("OVERLOAD PON OFF")); overloadNow=false; setLastPowerChange(); } if (microsSinceLastPowerChange() > POWER_SAMPLE_ALL_GOOD) { power_sample_overload_wait = POWER_SAMPLE_OVERLOAD_WAIT; } } else { // too much current if (!overloadNow) { // current is over trip value, turn on overload condition // DIAG(F("OVERLOAD PON ON")); overloadNow=true; setLastPowerChange(); } unsigned long uSecs = microsSinceLastPowerChange(); if (power_sample_overload_wait > POWER_SAMPLE_OVERLOAD_WAIT || // not virgin uSecs > POWER_SAMPLE_OFF_DELAY) { // Overload has existed longer than delay (typ. 10ms) setPower(POWERMODE::OVERLOAD); if (overloadNow) { // the setPower just turned off, so overload is now gone // DIAG(F("OVERLOAD PON OFF")); overloadNow=false; setLastPowerChangeOverload(); } unsigned int mA=raw2mA(lastCurrent); unsigned int maxmA=raw2mA(tripValue); DIAG(F("TRACK %c POWER OVERLOAD %4dmA (max %4dmA) detected after %4M. Pause %4M"), trackno + 'A', mA, maxmA, uSecs, power_sample_overload_wait); } } break; case POWERMODE::OVERLOAD: { // Try setting it back on after the OVERLOAD_WAIT unsigned long mslpc = (commonFaultPin ? (micros() - globalOverloadStart) : microsSinceLastPowerChange()); if (mslpc > power_sample_overload_wait) { // adjust next wait time power_sample_overload_wait *= 2; if (power_sample_overload_wait > POWER_SAMPLE_RETRY_MAX) power_sample_overload_wait = POWER_SAMPLE_RETRY_MAX; // power on test setPower(POWERMODE::ON); // here we change power but not the overloadNow as that was // already changed to false when we entered POWERMODE::OVERLOAD // so we need to set the lastPowerChange anyway. overloadNow=false; setLastPowerChange(); DIAG(F("TRACK %c POWER RESTORE (after %4M)"), trackno + 'A', mslpc); } } break; default: break; } }