dani/CommandStation-EX
1
0
Fork 0
mirror of https://github.com/DCC-EX/CommandStation-EX.git synced 2024-11-23 08:06:13 +01:00
Code Releases Activity
1941402c52
CommandStation-EX/SSD1306Ascii.cpp
Neil McKechnie 38be1d6152
Refactor OLED and LCD drivers (#178) 
* Refactor SSD and LCD drivers

Rework display drivers to use inheritance and to remove unused functionality.  The changes here were previously in neil-hal branch but have been separated out because of the amount of changes in neil-hal.

* Update version.h
2021-07-13 21:15:38 +01:00

394 lines
15 KiB
C++
Raw Blame History

/* Based on Arduino SSD1306Ascii Library, Copyright (C) 2015 by William Greiman
* Modifications (C) 2021 Neil McKechnie
*
* This Library is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This Library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with the Arduino SSD1306Ascii Library. If not, see
* <http://www.gnu.org/licenses/>.
*/
#include "SSD1306Ascii.h"
#include "I2CManager.h"
#include "FSH.h"
//==============================================================================
// SSD1306/SSD1106 I2C command bytes
//------------------------------------------------------------------------------
/** Set Lower Column Start Address for Page Addressing Mode. */
static const uint8_t SSD1306_SETLOWCOLUMN = 0x00;
/** Set Higher Column Start Address for Page Addressing Mode. */
static const uint8_t SSD1306_SETHIGHCOLUMN = 0x10;
/** Set Memory Addressing Mode. */
static const uint8_t SSD1306_MEMORYMODE = 0x20;
/** Set display RAM display start line register from 0 - 63. */
static const uint8_t SSD1306_SETSTARTLINE = 0x40;
/** Set Display Contrast to one of 256 steps. */
static const uint8_t SSD1306_SETCONTRAST = 0x81;
/** Enable or disable charge pump. Follow with 0X14 enable, 0X10 disable. */
static const uint8_t SSD1306_CHARGEPUMP = 0x8D;
/** Set Segment Re-map between data column and the segment driver. */
static const uint8_t SSD1306_SEGREMAP = 0xA0;
/** Resume display from GRAM content. */
static const uint8_t SSD1306_DISPLAYALLON_RESUME = 0xA4;
/** Force display on regardless of GRAM content. */
static const uint8_t SSD1306_DISPLAYALLON = 0xA5;
/** Set Normal Display. */
static const uint8_t SSD1306_NORMALDISPLAY = 0xA6;
/** Set Inverse Display. */
static const uint8_t SSD1306_INVERTDISPLAY = 0xA7;
/** Set Multiplex Ratio from 16 to 63. */
static const uint8_t SSD1306_SETMULTIPLEX = 0xA8;
/** Set Display off. */
static const uint8_t SSD1306_DISPLAYOFF = 0xAE;
/** Set Display on. */
static const uint8_t SSD1306_DISPLAYON = 0xAF;
/**Set GDDRAM Page Start Address. */
static const uint8_t SSD1306_SETSTARTPAGE = 0xB0;
/** Set COM output scan direction normal. */
static const uint8_t SSD1306_COMSCANINC = 0xC0;
/** Set COM output scan direction reversed. */
static const uint8_t SSD1306_COMSCANDEC = 0xC8;
/** Set Display Offset. */
static const uint8_t SSD1306_SETDISPLAYOFFSET = 0xD3;
/** Sets COM signals pin configuration to match the OLED panel layout. */
static const uint8_t SSD1306_SETCOMPINS = 0xDA;
/** This command adjusts the VCOMH regulator output. */
static const uint8_t SSD1306_SETVCOMDETECT = 0xDB;
/** Set Display Clock Divide Ratio/ Oscillator Frequency. */
static const uint8_t SSD1306_SETDISPLAYCLOCKDIV = 0xD5;
/** Set Pre-charge Period */
static const uint8_t SSD1306_SETPRECHARGE = 0xD9;
/** Deactivate scroll */
static const uint8_t SSD1306_DEACTIVATE_SCROLL = 0x2E;
/** No Operation Command. */
static const uint8_t SSD1306_NOP = 0xE3;
//------------------------------------------------------------------------------
/** Set Pump voltage value: (30H~33H) 6.4, 7.4, 8.0 (POR), 9.0. */
static const uint8_t SH1106_SET_PUMP_VOLTAGE = 0x30;
/** First byte of set charge pump mode */
static const uint8_t SH1106_SET_PUMP_MODE = 0xAD;
/** Second byte charge pump on. */
static const uint8_t SH1106_PUMP_ON = 0x8B;
/** Second byte charge pump off. */
static const uint8_t SH1106_PUMP_OFF = 0x8A;
//------------------------------------------------------------------------------
// Sequence of blank pixels, to optimise clearing screen.
// Send a maximum of 30 pixels per transmission.
const uint8_t FLASH SSD1306AsciiWire::blankPixels[30] =
{0x40, // First byte specifies data mode
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
//==============================================================================
// SSD1306AsciiWire Method Definitions
//------------------------------------------------------------------------------
// Constructor
SSD1306AsciiWire::SSD1306AsciiWire(int width, int height) {
// Set size in characters in base class
lcdRows = height / 8;
lcdCols = width / 6;
I2CManager.begin();
I2CManager.setClock(400000L); // Set max supported I2C speed
for (byte address = 0x3c; address <= 0x3d; address++) {
if (I2CManager.exists(address)) {
// Device found
DIAG(F("%dx%d OLED display configured on I2C:x%x"), width, height, address);
if (width == 132)
begin(&SH1106_132x64, address);
else if (height == 32)
begin(&Adafruit128x32, address);
else
begin(&Adafruit128x64, address);
// Set singleton address
lcdDisplay = this;
clear();
return;
}
}
DIAG(F("OLED display not found"));
}
/* Clear screen by writing blank pixels. */
void SSD1306AsciiWire::clearNative() {
const int maxBytes = sizeof(blankPixels); // max number of bytes sendable over Wire
for (uint8_t r = 0; r <= m_displayHeight/8 - 1; r++) {
setRowNative(r); // Position at start of row to be erased
for (uint8_t c = 0; c <= m_displayWidth - 1; c += maxBytes-1) {
uint8_t len = min(m_displayWidth-c, maxBytes-1) + 1;
I2CManager.write_P(m_i2cAddr, blankPixels, len); // Write a number of blank columns
}
}
}
// Initialise device
void SSD1306AsciiWire::begin(const DevType* dev, uint8_t i2cAddr) {
m_i2cAddr = i2cAddr;
m_col = 0;
m_row = 0;
const uint8_t* table = (const uint8_t*)GETFLASHW(&dev->initcmds);
uint8_t size = GETFLASH(&dev->initSize);
m_displayWidth = GETFLASH(&dev->lcdWidth);
m_displayHeight = GETFLASH(&dev->lcdHeight);
m_colOffset = GETFLASH(&dev->colOffset);
I2CManager.write_P(m_i2cAddr, table, size);
if (m_displayHeight == 32)
I2CManager.write(m_i2cAddr, 5, 0, // Set command mode
SSD1306_SETMULTIPLEX, 0x1F, // ratio 32
SSD1306_SETCOMPINS, 0x02); // sequential COM pins, disable remap
}
//------------------------------------------------------------------------------
// Set cursor position (by text line)
void SSD1306AsciiWire::setRowNative(uint8_t line) {
// Calculate pixel position from line number
uint8_t row = line*8;
if (row < m_displayHeight) {
m_row = row;
m_col = m_colOffset;
// Build output buffer for I2C
uint8_t len = 0;
outputBuffer[len++] = 0x00; // Set to command mode
outputBuffer[len++] = SSD1306_SETLOWCOLUMN | (m_col & 0XF);
outputBuffer[len++] = SSD1306_SETHIGHCOLUMN | (m_col >> 4);
outputBuffer[len++] = SSD1306_SETSTARTPAGE | (m_row/8);
I2CManager.write(m_i2cAddr, outputBuffer, len);
}
}
//------------------------------------------------------------------------------
// Write a character to the OLED
size_t SSD1306AsciiWire::writeNative(uint8_t ch) {
const uint8_t* base = m_font;
if (ch < m_fontFirstChar || ch >= (m_fontFirstChar + m_fontCharCount))
return 0;
// Check if character would be partly or wholly off the display
if (m_col + fontWidth > m_displayWidth)
return 0;
#if defined(NOLOWERCASE)
// Adjust if lowercase is missing
if (ch >= 'a') {
if (ch <= 'z')
ch = ch - 'a' + 'A'; // Capitalise
else
ch -= 26; // Allow for missing lowercase letters
}
#endif
ch -= m_fontFirstChar;
base += fontWidth * ch;
// Build output buffer for I2C
outputBuffer[0] = 0x40; // set SSD1306 controller to data mode
uint8_t bufferPos = 1;
// Copy character pixel columns
for (uint8_t i = 0; i < fontWidth; i++)
outputBuffer[bufferPos++] = GETFLASH(base++);
// Add blank pixels between letters
for (uint8_t i = 0; i < letterSpacing; i++)
outputBuffer[bufferPos++] = 0;
// Write the data to I2C display
I2CManager.write(m_i2cAddr, outputBuffer, bufferPos);
m_col += fontWidth + letterSpacing;
return 1;
}
//==============================================================================
// this section is based on https://github.com/adafruit/Adafruit_SSD1306
/** Initialization commands for a 128x32 or 128x64 SSD1306 oled display. */
const uint8_t FLASH SSD1306AsciiWire::Adafruit128xXXinit[] = {
// Init sequence for Adafruit 128x32/64 OLED module
0x00, // Set to command mode
SSD1306_DISPLAYOFF,
SSD1306_SETDISPLAYCLOCKDIV, 0x80, // the suggested ratio 0x80
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64 (initially)
SSD1306_SETDISPLAYOFFSET, 0x0, // no offset
SSD1306_SETSTARTLINE | 0x0, // line #0
SSD1306_CHARGEPUMP, 0x14, // internal vcc
SSD1306_MEMORYMODE, 0x02, // page mode
SSD1306_SEGREMAP | 0x1, // column 127 mapped to SEG0
SSD1306_COMSCANDEC, // column scan direction reversed
SSD1306_SETCOMPINS, 0X12, // set COM pins
SSD1306_SETCONTRAST, 0x7F, // contrast level 127
SSD1306_SETPRECHARGE, 0xF1, // pre-charge period (1, 15)
SSD1306_SETVCOMDETECT, 0x40, // vcomh regulator level
SSD1306_DISPLAYALLON_RESUME,
SSD1306_NORMALDISPLAY,
SSD1306_DISPLAYON
};
/** Initialize a 128x32 SSD1306 oled display. */
const DevType FLASH SSD1306AsciiWire::Adafruit128x32 = {
Adafruit128xXXinit,
sizeof(Adafruit128xXXinit),
128,
32,
0
};
/** Initialize a 128x64 oled display. */
const DevType FLASH SSD1306AsciiWire::Adafruit128x64 = {
Adafruit128xXXinit,
sizeof(Adafruit128xXXinit),
128,
64,
0
};
//------------------------------------------------------------------------------
// This section is based on https://github.com/stanleyhuangyc/MultiLCD
/** Initialization commands for a 128x64 SH1106 oled display. */
const uint8_t FLASH SSD1306AsciiWire::SH1106_132x64init[] = {
0x00, // Set to command mode
SSD1306_DISPLAYOFF,
SSD1306_SETDISPLAYCLOCKDIV, 0X80, // set osc division
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64
SSD1306_SETDISPLAYOFFSET, 0X00, // set display offset
SSD1306_SETSTARTPAGE | 0X0, // set page address
SSD1306_SETSTARTLINE | 0x0, // set start line
SH1106_SET_PUMP_MODE, SH1106_PUMP_ON, // set charge pump enable
SSD1306_SEGREMAP | 0X1, // set segment remap
SSD1306_COMSCANDEC, // Com scan direction
SSD1306_SETCOMPINS, 0X12, // set COM pins
SSD1306_SETCONTRAST, 0x80, // 128
SSD1306_SETPRECHARGE, 0X1F, // set pre-charge period
SSD1306_SETVCOMDETECT, 0x40, // set vcomh
SH1106_SET_PUMP_VOLTAGE | 0X2, // 8.0 volts
SSD1306_NORMALDISPLAY, // normal / reverse
SSD1306_DISPLAYON
};
/** Initialize a 132x64 oled SH1106 display. */
const DevType FLASH SSD1306AsciiWire::SH1106_132x64 = {
SH1106_132x64init,
sizeof(SH1106_132x64init),
128,
64,
2 // SH1106 is a 132x64 controller but most OLEDs are only attached
// to columns 2-129.
};
//------------------------------------------------------------------------------
// Font characters, 5x7 pixels, 0x61 characters starting at 0x20.
// Lower case characters optionally omitted.
const uint8_t FLASH SSD1306AsciiWire::System5x7[] = {
// Fixed width; char width table not used !!!!
// or with lowercase character omitted.
// font data
0x00, 0x00, 0x00, 0x00, 0x00, // (space)
0x00, 0x00, 0x5F, 0x00, 0x00, // !
0x00, 0x07, 0x00, 0x07, 0x00, // "
0x14, 0x7F, 0x14, 0x7F, 0x14, // #
0x24, 0x2A, 0x7F, 0x2A, 0x12, // $
0x23, 0x13, 0x08, 0x64, 0x62, // %
0x36, 0x49, 0x55, 0x22, 0x50, // &
0x00, 0x05, 0x03, 0x00, 0x00, // '
0x00, 0x1C, 0x22, 0x41, 0x00, // (
0x00, 0x41, 0x22, 0x1C, 0x00, // )
0x08, 0x2A, 0x1C, 0x2A, 0x08, // *
0x08, 0x08, 0x3E, 0x08, 0x08, // +
0x00, 0x50, 0x30, 0x00, 0x00, // ,
0x08, 0x08, 0x08, 0x08, 0x08, // -
0x00, 0x60, 0x60, 0x00, 0x00, // .
0x20, 0x10, 0x08, 0x04, 0x02, // /
0x3E, 0x51, 0x49, 0x45, 0x3E, // 0
0x00, 0x42, 0x7F, 0x40, 0x00, // 1
0x42, 0x61, 0x51, 0x49, 0x46, // 2
0x21, 0x41, 0x45, 0x4B, 0x31, // 3
0x18, 0x14, 0x12, 0x7F, 0x10, // 4
0x27, 0x45, 0x45, 0x45, 0x39, // 5
0x3C, 0x4A, 0x49, 0x49, 0x30, // 6
0x01, 0x71, 0x09, 0x05, 0x03, // 7
0x36, 0x49, 0x49, 0x49, 0x36, // 8
0x06, 0x49, 0x49, 0x29, 0x1E, // 9
0x00, 0x36, 0x36, 0x00, 0x00, // :
0x00, 0x56, 0x36, 0x00, 0x00, // ;
0x00, 0x08, 0x14, 0x22, 0x41, // <
0x14, 0x14, 0x14, 0x14, 0x14, // =
0x41, 0x22, 0x14, 0x08, 0x00, // >
0x02, 0x01, 0x51, 0x09, 0x06, // ?
0x32, 0x49, 0x79, 0x41, 0x3E, // @
0x7E, 0x11, 0x11, 0x11, 0x7E, // A
0x7F, 0x49, 0x49, 0x49, 0x36, // B
0x3E, 0x41, 0x41, 0x41, 0x22, // C
0x7F, 0x41, 0x41, 0x22, 0x1C, // D
0x7F, 0x49, 0x49, 0x49, 0x41, // E
0x7F, 0x09, 0x09, 0x01, 0x01, // F
0x3E, 0x41, 0x41, 0x51, 0x32, // G
0x7F, 0x08, 0x08, 0x08, 0x7F, // H
0x00, 0x41, 0x7F, 0x41, 0x00, // I
0x20, 0x40, 0x41, 0x3F, 0x01, // J
0x7F, 0x08, 0x14, 0x22, 0x41, // K
0x7F, 0x40, 0x40, 0x40, 0x40, // L
0x7F, 0x02, 0x04, 0x02, 0x7F, // M
0x7F, 0x04, 0x08, 0x10, 0x7F, // N
0x3E, 0x41, 0x41, 0x41, 0x3E, // O
0x7F, 0x09, 0x09, 0x09, 0x06, // P
0x3E, 0x41, 0x51, 0x21, 0x5E, // Q
0x7F, 0x09, 0x19, 0x29, 0x46, // R
0x46, 0x49, 0x49, 0x49, 0x31, // S
0x01, 0x01, 0x7F, 0x01, 0x01, // T
0x3F, 0x40, 0x40, 0x40, 0x3F, // U
0x1F, 0x20, 0x40, 0x20, 0x1F, // V
0x7F, 0x20, 0x18, 0x20, 0x7F, // W
0x63, 0x14, 0x08, 0x14, 0x63, // X
0x03, 0x04, 0x78, 0x04, 0x03, // Y
0x61, 0x51, 0x49, 0x45, 0x43, // Z
0x00, 0x00, 0x7F, 0x41, 0x41, // [
0x02, 0x04, 0x08, 0x10, 0x20, // "\"
0x41, 0x41, 0x7F, 0x00, 0x00, // ]
0x04, 0x02, 0x01, 0x02, 0x04, // ^
0x40, 0x40, 0x40, 0x40, 0x40, // _
0x00, 0x01, 0x02, 0x04, 0x00, // `
#ifndef NOLOWERCASE
0x20, 0x54, 0x54, 0x54, 0x78, // a
0x7F, 0x48, 0x44, 0x44, 0x38, // b
0x38, 0x44, 0x44, 0x44, 0x20, // c
0x38, 0x44, 0x44, 0x48, 0x7F, // d
0x38, 0x54, 0x54, 0x54, 0x18, // e
0x08, 0x7E, 0x09, 0x01, 0x02, // f
0x08, 0x14, 0x54, 0x54, 0x3C, // g
0x7F, 0x08, 0x04, 0x04, 0x78, // h
0x00, 0x44, 0x7D, 0x40, 0x00, // i
0x20, 0x40, 0x44, 0x3D, 0x00, // j
0x00, 0x7F, 0x10, 0x28, 0x44, // k
0x00, 0x41, 0x7F, 0x40, 0x00, // l
0x7C, 0x04, 0x18, 0x04, 0x78, // m
0x7C, 0x08, 0x04, 0x04, 0x78, // n
0x38, 0x44, 0x44, 0x44, 0x38, // o
0x7C, 0x14, 0x14, 0x14, 0x08, // p
0x08, 0x14, 0x14, 0x18, 0x7C, // q
0x7C, 0x08, 0x04, 0x04, 0x08, // r
0x48, 0x54, 0x54, 0x54, 0x20, // s
0x04, 0x3F, 0x44, 0x40, 0x20, // t
0x3C, 0x40, 0x40, 0x20, 0x7C, // u
0x1C, 0x20, 0x40, 0x20, 0x1C, // v
0x3C, 0x40, 0x30, 0x40, 0x3C, // w
0x44, 0x28, 0x10, 0x28, 0x44, // x
0x0C, 0x50, 0x50, 0x50, 0x3C, // y
0x44, 0x64, 0x54, 0x4C, 0x44, // z
#endif
0x00, 0x08, 0x36, 0x41, 0x00, // {
0x00, 0x00, 0x7F, 0x00, 0x00, // |
0x00, 0x41, 0x36, 0x08, 0x00, // }
0x08, 0x08, 0x2A, 0x1C, 0x08, // ->
0x08, 0x1C, 0x2A, 0x08, 0x08, // <-
0x00, 0x06, 0x09, 0x09, 0x06 // degree symbol
};
View Git Blame Copy Permalink