dani/CommandStation-EX
1
0
Fork 0
mirror of https://github.com/DCC-EX/CommandStation-EX.git synced 2024-11-27 01:56:14 +01:00
Code Releases Activity
37f44709f9
CommandStation-EX/DCC.cpp
Harald Barth 237846f190 clean up diag, multiple gpio pin test worked
2022-07-30 15:47:19 +02:00

1026 lines
34 KiB
C++
Raw Blame History

/*
* © 2020, Chris Harlow. All rights reserved.
* © 2020, Harald Barth
*
* This file is part of Asbelos DCC API
*
* This is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* It is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with CommandStation. If not, see <https://www.gnu.org/licenses/>.
*/
#include "DIAG.h"
#include "DCC.h"
#include "DCCWaveform.h"
#include "DCCTrack.h"
#include "EEStore.h"
#include "GITHUB_SHA.h"
#include "version.h"
#include "FSH.h"
#include "IODevice.h"
#include "MotorDriver.h"
// This module is responsible for converting API calls into
// messages to be sent to the waveform generator.
// It has no visibility of the hardware, timers, interrupts
// nor of the waveform issues such as preambles, start bits checksums or cutouts.
//
// Nor should it have to deal with JMRI responsess other than the OK/FAIL
// or cv value returned. I will move that back to the JMRI interface later
//
// The interface to the waveform generator is narrowed down to merely:
// Scheduling a message on the prog or main track using a function
// Obtaining ACKs from the prog track using a function
// There are no volatiles here.
const byte FN_GROUP_1=0x01;
const byte FN_GROUP_2=0x02;
const byte FN_GROUP_3=0x04;
const byte FN_GROUP_4=0x08;
const byte FN_GROUP_5=0x10;
FSH* DCC::shieldName=NULL;
byte DCC::joinRelay=UNUSED_PIN;
byte DCC::globalSpeedsteps=128;
void DCC::begin() {
StringFormatter::send(Serial,F("<iDCC-EX V-%S / %S / %S G-%S>\n"), F(VERSION), F(ARDUINO_TYPE),
MotorDriverContainer::mDC.getMotorShieldName(), F(GITHUB_SHA));
// BE AWARE, USES I2C PINS, MAY LEAD TO PIN CONFLICTS
// Initialise HAL layer before reading EEprom.
IODevice::begin();
//example how to use add:
//MotorDriverContainer::mDC.add(new MotorDriver(16, 21, UNUSED_PIN, UNUSED_PIN, UNUSED_PIN, 2.00, 2000, UNUSED_PIN, RMT_MAIN));
// Load stuff from EEprom
(void)EEPROM; // tell compiler not to warn this is unused
EEStore::init();
MotorDriverContainer::mDC.diag();
DCCWaveform::begin(MotorDriverContainer::mDC.mainTrack(),MotorDriverContainer::mDC.progTrack());
// Add main and prog drivers to the main and prog packet sources (dcc-tracks).
std::vector<MotorDriver*> v;
v = MotorDriverContainer::mDC.getDriverType(RMT_MAIN|TIMER_MAIN);
for (const auto& d: v) DCCTrack::mainTrack.addDriver(d);
v = MotorDriverContainer::mDC.getDriverType(RMT_PROG|TIMER_PROG);
for (const auto& d: v) DCCTrack::progTrack.addDriver(d);
}
void DCC::setJoinRelayPin(byte joinRelayPin) {
joinRelay=joinRelayPin;
if (joinRelay!=UNUSED_PIN) {
pinMode(joinRelay,OUTPUT);
digitalWrite(joinRelay,LOW); // LOW is relay disengaged
}
}
void DCC::setThrottle( uint16_t cab, uint8_t tSpeed, bool tDirection) {
byte speedCode = (tSpeed & 0x7F) + tDirection * 128;
setThrottle2(cab, speedCode);
// retain speed for loco reminders
updateLocoReminder(cab, speedCode );
}
void DCC::setThrottle2( uint16_t cab, byte speedCode) {
uint8_t b[4];
uint8_t nB = 0;
// DIAG(F("setSpeedInternal %d %x"),cab,speedCode);
if (cab > 127)
b[nB++] = highByte(cab) | 0xC0; // convert train number into a two-byte address
b[nB++] = lowByte(cab);
if (globalSpeedsteps <= 28) {
uint8_t speed128 = speedCode & 0x7F;
uint8_t speed28;
uint8_t code28;
if (speed128 == 0 || speed128 == 1) { // stop or emergency stop
code28 = speed128;
} else {
speed28= (speed128*10+36)/46; // convert 2-127 to 1-28
/*
if (globalSpeedsteps <= 14) // Don't want to do 14 steps, to get F0 there is ugly
code28 = (speed28+3)/2 | (Value of F0); // convert 1-28 to DCC 14 step speed code
else
*/
code28 = (speed28+3)/2 | ( (speed28 & 1) ? 0 : 0b00010000 ); // convert 1-28 to DCC 28 step speed code
}
// Construct command byte from:
// command speed direction
b[nB++] = 0b01000000 | code28 | ((speedCode & 0x80) ? 0b00100000 : 0);
} else { // 128 speedsteps
b[nB++] = SET_SPEED; // 128-step speed control byte
b[nB++] = speedCode; // for encoding see setThrottle
}
DCCTrack::mainTrack.schedulePacket(b, nB, 0);
}
void DCC::setFunctionInternal(int cab, byte byte1, byte byte2) {
// DIAG(F("setFunctionInternal %d %x %x"),cab,byte1,byte2);
byte b[4];
byte nB = 0;
if (cab > 127)
b[nB++] = highByte(cab) | 0xC0; // convert train number into a two-byte address
b[nB++] = lowByte(cab);
if (byte1!=0) b[nB++] = byte1;
b[nB++] = byte2;
DCCTrack::mainTrack.schedulePacket(b, nB, 0);
}
uint8_t DCC::getThrottleSpeed(int cab) {
int reg=lookupSpeedTable(cab);
if (reg<0) return -1;
return speedTable[reg].speedCode & 0x7F;
}
bool DCC::getThrottleDirection(int cab) {
int reg=lookupSpeedTable(cab);
if (reg<0) return true;
return (speedTable[reg].speedCode & 0x80) !=0;
}
// Set function to value on or off
void DCC::setFn( int cab, int16_t functionNumber, bool on) {
if (cab<=0 ) return;
if (functionNumber>28) {
//non reminding advanced binary bit set
byte b[5];
byte nB = 0;
if (cab > 127)
b[nB++] = highByte(cab) | 0xC0; // convert train number into a two-byte address
b[nB++] = lowByte(cab);
if (functionNumber <= 127) {
b[nB++] = 0b11011101; // Binary State Control Instruction short form
b[nB++] = functionNumber | (on ? 0x80 : 0);
}
else {
b[nB++] = 0b11000000; // Binary State Control Instruction long form
b[nB++] = (functionNumber & 0x7F) | (on ? 0x80 : 0); // low order bits and state flag
b[nB++] = functionNumber >>7 ; // high order bits
}
DCCTrack::mainTrack.schedulePacket(b, nB, 3);
return;
}
int reg = lookupSpeedTable(cab);
if (reg<0) return;
// Take care of functions:
// Set state of function
unsigned long funcmask = (1UL<<functionNumber);
if (on) {
speedTable[reg].functions |= funcmask;
} else {
speedTable[reg].functions &= ~funcmask;
}
updateGroupflags(speedTable[reg].groupFlags, functionNumber);
return;
}
// Change function according to how button was pressed,
// typically in WiThrottle.
// Returns new state or -1 if nothing was changed.
int DCC::changeFn( int cab, int16_t functionNumber, bool pressed) {
int funcstate = -1;
if (cab<=0 || functionNumber>28) return funcstate;
int reg = lookupSpeedTable(cab);
if (reg<0) return funcstate;
// Take care of functions:
// Imitate how many command stations do it: Button press is
// toggle but for F2 where it is momentary
unsigned long funcmask = (1UL<<functionNumber);
if (functionNumber == 2) {
// turn on F2 on press and off again at release of button
if (pressed) {
speedTable[reg].functions |= funcmask;
funcstate = 1;
} else {
speedTable[reg].functions &= ~funcmask;
funcstate = 0;
}
} else {
// toggle function on press, ignore release
if (pressed) {
speedTable[reg].functions ^= funcmask;
}
funcstate = (speedTable[reg].functions & funcmask)? 1 : 0;
}
updateGroupflags(speedTable[reg].groupFlags, functionNumber);
return funcstate;
}
int DCC::getFn( int cab, int16_t functionNumber) {
if (cab<=0 || functionNumber>28) return -1; // unknown
int reg = lookupSpeedTable(cab);
if (reg<0) return -1;
unsigned long funcmask = (1UL<<functionNumber);
return (speedTable[reg].functions & funcmask)? 1 : 0;
}
// Set the group flag to say we have touched the particular group.
// A group will be reminded only if it has been touched.
void DCC::updateGroupflags(byte & flags, int16_t functionNumber) {
byte groupMask;
if (functionNumber<=4) groupMask=FN_GROUP_1;
else if (functionNumber<=8) groupMask=FN_GROUP_2;
else if (functionNumber<=12) groupMask=FN_GROUP_3;
else if (functionNumber<=20) groupMask=FN_GROUP_4;
else groupMask=FN_GROUP_5;
flags |= groupMask;
}
void DCC::setAccessory(int address, byte number, bool activate) {
#ifdef DIAG_IO
DIAG(F("DCC::setAccessory(%d,%d,%d)"), address, number, activate);
#endif
// use masks to detect wrong values and do nothing
if(address != (address & 511))
return;
if(number != (number & 3))
return;
byte b[2];
b[0] = address % 64 + 128; // first byte is of the form 10AAAAAA, where AAAAAA represent 6 least signifcant bits of accessory address
b[1] = ((((address / 64) % 8) << 4) + (number % 4 << 1) + activate % 2) ^ 0xF8; // second byte is of the form 1AAACDDD, where C should be 1, and the least significant D represent activate/deactivate
DCCTrack::mainTrack.schedulePacket(b, 2, 3); // Repeat the packet four times (3 2 1 0)
}
//
// writeCVByteMain: Write a byte with PoM on main. This writes
// the 5 byte sized packet to implement this DCC function
//
void DCC::writeCVByteMain(int cab, int cv, byte bValue) {
byte b[5];
byte nB = 0;
if (cab > 127)
b[nB++] = highByte(cab) | 0xC0; // convert train number into a two-byte address
b[nB++] = lowByte(cab);
b[nB++] = cv1(WRITE_BYTE_MAIN, cv); // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
b[nB++] = cv2(cv);
b[nB++] = bValue;
DCCTrack::mainTrack.schedulePacket(b, nB, 3);
}
//
// writeCVBitMain: Write a bit of a byte with PoM on main. This writes
// the 5 byte sized packet to implement this DCC function
//
void DCC::writeCVBitMain(int cab, int cv, byte bNum, bool bValue) {
byte b[5];
byte nB = 0;
bValue = bValue % 2;
bNum = bNum % 8;
if (cab > 127)
b[nB++] = highByte(cab) | 0xC0; // convert train number into a two-byte address
b[nB++] = lowByte(cab);
b[nB++] = cv1(WRITE_BIT_MAIN, cv); // any CV>1023 will become modulus(1024) due to bit-mask of 0x03
b[nB++] = cv2(cv);
b[nB++] = WRITE_BIT | (bValue ? BIT_ON : BIT_OFF) | bNum;
DCCTrack::mainTrack.schedulePacket(b, nB, 3);
}
void DCC::setProgTrackSyncMain(bool on) {
if (joinRelay!=UNUSED_PIN) digitalWrite(joinRelay,on?HIGH:LOW);
DCCWaveform::progTrackSyncMain=on;
}
void DCC::setProgTrackBoost(bool on) {
DCCWaveform::progTrackBoosted=on;
}
FSH* DCC::getMotorShieldName() {
return shieldName;
}
const ackOp FLASH WRITE_BIT0_PROG[] = {
BASELINE,
W0,WACK,
V0, WACK, // validate bit is 0
ITC1, // if acked, callback(1)
CALLFAIL // callback (-1)
};
const ackOp FLASH WRITE_BIT1_PROG[] = {
BASELINE,
W1,WACK,
V1, WACK, // validate bit is 1
ITC1, // if acked, callback(1)
CALLFAIL // callback (-1)
};
const ackOp FLASH VERIFY_BIT0_PROG[] = {
BASELINE,
V0, WACK, // validate bit is 0
ITC0, // if acked, callback(0)
V1, WACK, // validate bit is 1
ITC1,
CALLFAIL // callback (-1)
};
const ackOp FLASH VERIFY_BIT1_PROG[] = {
BASELINE,
V1, WACK, // validate bit is 1
ITC1, // if acked, callback(1)
V0, WACK,
ITC0,
CALLFAIL // callback (-1)
};
const ackOp FLASH READ_BIT_PROG[] = {
BASELINE,
V1, WACK, // validate bit is 1
ITC1, // if acked, callback(1)
V0, WACK, // validate bit is zero
ITC0, // if acked callback 0
CALLFAIL // bit not readable
};
const ackOp FLASH WRITE_BYTE_PROG[] = {
BASELINE,
WB,WACK,ITC1, // Write and callback(1) if ACK
// handle decoders that dont ack a write
VB,WACK,ITC1, // validate byte and callback(1) if correct
CALLFAIL // callback (-1)
};
const ackOp FLASH VERIFY_BYTE_PROG[] = {
BASELINE,
BIV, // ackManagerByte initial value
VB,WACK, // validate byte
ITCB, // if ok callback value
STARTMERGE, //clear bit and byte values ready for merge pass
// each bit is validated against 0 and the result inverted in MERGE
// this is because there tend to be more zeros in cv values than ones.
// There is no need for one validation as entire byte is validated at the end
V0, WACK, MERGE, // read and merge first tested bit (7)
ITSKIP, // do small excursion if there was no ack
SETBIT,(ackOp)7,
V1, WACK, NAKFAIL, // test if there is an ack on the inverse of this bit (7)
SETBIT,(ackOp)6, // and abort whole test if not else continue with bit (6)
SKIPTARGET,
V0, WACK, MERGE, // read and merge second tested bit (6)
V0, WACK, MERGE, // read and merge third tested bit (5) ...
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, ITCBV, // verify merged byte and return it if acked ok - with retry report
CALLFAIL };
const ackOp FLASH READ_CV_PROG[] = {
BASELINE,
STARTMERGE, //clear bit and byte values ready for merge pass
// each bit is validated against 0 and the result inverted in MERGE
// this is because there tend to be more zeros in cv values than ones.
// There is no need for one validation as entire byte is validated at the end
V0, WACK, MERGE, // read and merge first tested bit (7)
ITSKIP, // do small excursion if there was no ack
SETBIT,(ackOp)7,
V1, WACK, NAKFAIL, // test if there is an ack on the inverse of this bit (7)
SETBIT,(ackOp)6, // and abort whole test if not else continue with bit (6)
SKIPTARGET,
V0, WACK, MERGE, // read and merge second tested bit (6)
V0, WACK, MERGE, // read and merge third tested bit (5) ...
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, ITCB, // verify merged byte and return it if acked ok
CALLFAIL }; // verification failed
const ackOp FLASH LOCO_ID_PROG[] = {
BASELINE,
SETCV, (ackOp)19, // CV 19 is consist setting
SETBYTE, (ackOp)0,
VB, WACK, ITSKIP, // ignore consist if cv19 is zero (no consist)
SETBYTE, (ackOp)128,
VB, WACK, ITSKIP, // ignore consist if cv19 is 128 (no consist, direction bit set)
STARTMERGE, // Setup to read cv 19
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, ITCB7, // return 7 bits only, No_ACK means CV19 not supported so ignore it
SKIPTARGET, // continue here if CV 19 is zero or fails all validation
SETCV,(ackOp)29,
SETBIT,(ackOp)5,
V0, WACK, ITSKIP, // Skip to SKIPTARGET if bit 5 of CV29 is zero
// Long locoid
SETCV, (ackOp)17, // CV 17 is part of locoid
STARTMERGE,
V0, WACK, MERGE, // read and merge bit 1 etc
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, NAKFAIL, // verify merged byte and return -1 it if not acked ok
STASHLOCOID, // keep stashed cv 17 for later
// Read 2nd part from CV 18
SETCV, (ackOp)18,
STARTMERGE,
V0, WACK, MERGE, // read and merge bit 1 etc
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, NAKFAIL, // verify merged byte and return -1 it if not acked ok
COMBINELOCOID, // Combile byte with stash to make long locoid and callback
// ITSKIP Skips to here if CV 29 bit 5 was zero. so read CV 1 and return that
SKIPTARGET,
SETCV, (ackOp)1,
STARTMERGE,
SETBIT, (ackOp)6, // skip over first bit as we know its a zero
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
V0, WACK, MERGE,
VB, WACK, ITCB, // verify merged byte and callback
CALLFAIL
};
const ackOp FLASH SHORT_LOCO_ID_PROG[] = {
BASELINE,
SETCV,(ackOp)19,
SETBYTE, (ackOp)0,
WB,WACK, // ignore dedcoder without cv19 support
// Turn off long address flag
SETCV,(ackOp)29,
SETBIT,(ackOp)5,
W0,WACK,
V0,WACK,NAKFAIL,
SETCV, (ackOp)1,
SETBYTEL, // low byte of word
WB,WACK, // some decoders don't ACK writes
VB,WACK,ITCB,
CALLFAIL
};
const ackOp FLASH LONG_LOCO_ID_PROG[] = {
BASELINE,
// Clear consist CV 19
SETCV,(ackOp)19,
SETBYTE, (ackOp)0,
WB,WACK, // ignore decoder without cv19 support
// Turn on long address flag cv29 bit 5
SETCV,(ackOp)29,
SETBIT,(ackOp)5,
W1,WACK,
V1,WACK,NAKFAIL,
// Store high byte of address in cv 17
SETCV, (ackOp)17,
SETBYTEH, // high byte of word
WB,WACK,
VB,WACK,NAKFAIL,
// store
SETCV, (ackOp)18,
SETBYTEL, // low byte of word
WB,WACK,
VB,WACK,ITC1, // callback(1) means Ok
CALLFAIL
};
void DCC::writeCVByte(int16_t cv, byte byteValue, ACK_CALLBACK callback) {
ackManagerSetup(cv, byteValue, WRITE_BYTE_PROG, callback);
}
void DCC::writeCVBit(int16_t cv, byte bitNum, bool bitValue, ACK_CALLBACK callback) {
if (bitNum >= 8) callback(-1);
else ackManagerSetup(cv, bitNum, bitValue?WRITE_BIT1_PROG:WRITE_BIT0_PROG, callback);
}
void DCC::verifyCVByte(int16_t cv, byte byteValue, ACK_CALLBACK callback) {
ackManagerSetup(cv, byteValue, VERIFY_BYTE_PROG, callback);
}
void DCC::verifyCVBit(int16_t cv, byte bitNum, bool bitValue, ACK_CALLBACK callback) {
if (bitNum >= 8) callback(-1);
else ackManagerSetup(cv, bitNum, bitValue?VERIFY_BIT1_PROG:VERIFY_BIT0_PROG, callback);
}
void DCC::readCVBit(int16_t cv, byte bitNum, ACK_CALLBACK callback) {
if (bitNum >= 8) callback(-1);
else ackManagerSetup(cv, bitNum,READ_BIT_PROG, callback);
}
void DCC::readCV(int16_t cv, ACK_CALLBACK callback) {
ackManagerSetup(cv, 0,READ_CV_PROG, callback);
}
void DCC::getLocoId(ACK_CALLBACK callback) {
ackManagerSetup(0,0, LOCO_ID_PROG, callback);
}
void DCC::setLocoId(int id,ACK_CALLBACK callback) {
if (id<1 || id>10239) { //0x27FF according to standard
callback(-1);
return;
}
if (id<=127)
ackManagerSetup(id, SHORT_LOCO_ID_PROG, callback);
else
ackManagerSetup(id | 0xc000,LONG_LOCO_ID_PROG, callback);
}
void DCC::forgetLoco(int cab) { // removes any speed reminders for this loco
setThrottle2(cab,1); // ESTOP this loco if still on track
int reg=lookupSpeedTable(cab);
if (reg>=0) speedTable[reg].loco=0;
setThrottle2(cab,1); // ESTOP if this loco still on track
}
void DCC::forgetAllLocos() { // removes all speed reminders
setThrottle2(0,1); // ESTOP all locos still on track
for (int i=0;i<MAX_LOCOS;i++) speedTable[i].loco=0;
}
byte DCC::loopStatus=0;
void DCC::loop() {
DCCWaveform::loop(ackManagerProg!=NULL); // power overload checks
MotorDriverContainer::mDC.loop();
ackManagerLoop(); // maintain prog track ack manager
issueReminders();
}
void DCC::issueReminders() {
// if the main track transmitter still has a pending packet, skip this time around.
if ( DCCWaveform::mainTrack.packetPending) return;
// This loop searches for a loco in the speed table starting at nextLoco and cycling back around
for (int reg=0;reg<MAX_LOCOS;reg++) {
int slot=reg+nextLoco;
if (slot>=MAX_LOCOS) slot-=MAX_LOCOS;
if (speedTable[slot].loco > 0) {
// have found the next loco to remind
// issueReminder will return true if this loco is completed (ie speed and functions)
if (issueReminder(slot)) nextLoco=slot+1;
return;
}
}
}
bool DCC::issueReminder(int reg) {
unsigned long functions=speedTable[reg].functions;
int loco=speedTable[reg].loco;
byte flags=speedTable[reg].groupFlags;
switch (loopStatus) {
case 0:
// DIAG(F("Reminder %d speed %d"),loco,speedTable[reg].speedCode);
setThrottle2(loco, speedTable[reg].speedCode);
break;
case 1: // remind function group 1 (F0-F4)
if (flags & FN_GROUP_1)
setFunctionInternal(loco,0, 128 | ((functions>>1)& 0x0F) | ((functions & 0x01)<<4)); // 100D DDDD
break;
case 2: // remind function group 2 F5-F8
if (flags & FN_GROUP_2)
setFunctionInternal(loco,0, 176 | ((functions>>5)& 0x0F)); // 1011 DDDD
break;
case 3: // remind function group 3 F9-F12
if (flags & FN_GROUP_3)
setFunctionInternal(loco,0, 160 | ((functions>>9)& 0x0F)); // 1010 DDDD
break;
case 4: // remind function group 4 F13-F20
if (flags & FN_GROUP_4)
setFunctionInternal(loco,222, ((functions>>13)& 0xFF));
flags&= ~FN_GROUP_4; // dont send them again
break;
case 5: // remind function group 5 F21-F28
if (flags & FN_GROUP_5)
setFunctionInternal(loco,223, ((functions>>21)& 0xFF));
flags&= ~FN_GROUP_5; // dont send them again
break;
}
loopStatus++;
// if we reach status 6 then this loco is done so
// reset status to 0 for next loco and return true so caller
// moves on to next loco.
if (loopStatus>5) loopStatus=0;
return loopStatus==0;
}
///// Private helper functions below here /////////////////////
byte DCC::cv1(byte opcode, int cv) {
cv--;
return (highByte(cv) & (byte)0x03) | opcode;
}
byte DCC::cv2(int cv) {
cv--;
return lowByte(cv);
}
int DCC::lookupSpeedTable(int locoId) {
// determine speed reg for this loco
int firstEmpty = MAX_LOCOS;
int reg;
for (reg = 0; reg < MAX_LOCOS; reg++) {
if (speedTable[reg].loco == locoId) break;
if (speedTable[reg].loco == 0 && firstEmpty == MAX_LOCOS) firstEmpty = reg;
}
if (reg == MAX_LOCOS) reg = firstEmpty;
if (reg >= MAX_LOCOS) {
DIAG(F("Too many locos"));
return -1;
}
if (reg==firstEmpty){
speedTable[reg].loco = locoId;
speedTable[reg].speedCode=128; // default direction forward
speedTable[reg].groupFlags=0;
speedTable[reg].functions=0;
}
return reg;
}
void DCC::updateLocoReminder(int loco, byte speedCode) {
if (loco==0) {
// broadcast stop/estop but dont change direction
for (int reg = 0; reg < MAX_LOCOS; reg++) {
speedTable[reg].speedCode = (speedTable[reg].speedCode & 0x80) | (speedCode & 0x7f);
}
return;
}
// determine speed reg for this loco
int reg=lookupSpeedTable(loco);
if (reg>=0) speedTable[reg].speedCode = speedCode;
}
DCC::LOCO DCC::speedTable[MAX_LOCOS];
int DCC::nextLoco = 0;
//ACK MANAGER
ackOp const * DCC::ackManagerProg;
ackOp const * DCC::ackManagerProgStart;
byte DCC::ackManagerByte;
byte DCC::ackManagerByteVerify;
byte DCC::ackManagerStash;
int DCC::ackManagerWord;
byte DCC::ackManagerRetry;
byte DCC::ackRetry = 2;
int16_t DCC::ackRetrySum;
int16_t DCC::ackRetryPSum;
int DCC::ackManagerCv;
byte DCC::ackManagerBitNum;
bool DCC::ackReceived;
bool DCC::ackManagerRejoin;
CALLBACK_STATE DCC::callbackState=READY;
ACK_CALLBACK DCC::ackManagerCallback;
void DCC::ackManagerSetup(int cv, byte byteValueOrBitnum, ackOp const program[], ACK_CALLBACK callback) {
if (!DCCWaveform::progTrack.canMeasureCurrent()) {
callback(-2);
return;
}
ackManagerRejoin=DCCWaveform::progTrackSyncMain;
if (ackManagerRejoin ) {
// Change from JOIN must zero resets packet.
setProgTrackSyncMain(false);
DCCWaveform::progTrack.sentResetsSincePacket = 0;
}
DCCWaveform::progTrack.autoPowerOff=false;
if (DCCWaveform::progTrack.getPowerMode() == POWERMODE::OFF) {
DCCWaveform::progTrack.autoPowerOff=true; // power off afterwards
if (Diag::ACK) DIAG(F("Auto Prog power on"));
DCCWaveform::progTrack.setPowerMode(POWERMODE::ON);
DCCWaveform::progTrack.sentResetsSincePacket = 0;
}
ackManagerCv = cv;
ackManagerProg = program;
ackManagerProgStart = program;
ackManagerRetry = ackRetry;
ackManagerByte = byteValueOrBitnum;
ackManagerByteVerify = byteValueOrBitnum;
ackManagerBitNum=byteValueOrBitnum;
ackManagerCallback = callback;
}
void DCC::ackManagerSetup(int wordval, ackOp const program[], ACK_CALLBACK callback) {
ackManagerWord=wordval;
ackManagerSetup(0, 0, program, callback);
}
const byte RESET_MIN=8; // tuning of reset counter before sending message
// checkRessets return true if the caller should yield back to loop and try later.
bool DCC::checkResets(uint8_t numResets) {
return DCCWaveform::progTrack.sentResetsSincePacket < numResets;
}
void DCC::ackManagerLoop() {
while (ackManagerProg) {
byte opcode=GETFLASH(ackManagerProg);
// breaks from this switch will step to next prog entry
// returns from this switch will stay on same entry
// (typically waiting for a reset counter or ACK waiting, or when all finished.)
switch (opcode) {
case BASELINE:
if (DCCWaveform::progTrack.getPowerMode()==POWERMODE::OVERLOAD) return;
if (checkResets(DCCWaveform::progTrack.autoPowerOff || ackManagerRejoin ? 20 : 3)) return;
DCCWaveform::progTrack.setAckBaseline();
callbackState=READY;
break;
case W0: // write 0 bit
case W1: // write 1 bit
{
if (checkResets(RESET_MIN)) return;
if (Diag::ACK) DIAG(F("W%d cv=%d bit=%d"),opcode==W1, ackManagerCv,ackManagerBitNum);
byte instruction = WRITE_BIT | (opcode==W1 ? BIT_ON : BIT_OFF) | ackManagerBitNum;
byte message[] = {cv1(BIT_MANIPULATE, ackManagerCv), cv2(ackManagerCv), instruction };
DCCTrack::progTrack.schedulePacket(message, sizeof(message), PROG_REPEATS);
DCCWaveform::progTrack.setAckPending();
callbackState=AFTER_WRITE;
}
break;
case WB: // write byte
{
if (checkResets( RESET_MIN)) return;
if (Diag::ACK) DIAG(F("WB cv=%d value=%d"),ackManagerCv,ackManagerByte);
byte message[] = {cv1(WRITE_BYTE, ackManagerCv), cv2(ackManagerCv), ackManagerByte};
DCCTrack::progTrack.schedulePacket(message, sizeof(message), PROG_REPEATS);
DCCWaveform::progTrack.setAckPending();
callbackState=AFTER_WRITE;
}
break;
case VB: // Issue validate Byte packet
{
if (checkResets( RESET_MIN)) return;
if (Diag::ACK) DIAG(F("VB cv=%d value=%d"),ackManagerCv,ackManagerByte);
byte message[] = { cv1(VERIFY_BYTE, ackManagerCv), cv2(ackManagerCv), ackManagerByte};
DCCTrack::progTrack.schedulePacket(message, sizeof(message), PROG_REPEATS);
DCCWaveform::progTrack.setAckPending();
}
break;
case V0:
case V1: // Issue validate bit=0 or bit=1 packet
{
if (checkResets(RESET_MIN)) return;
if (Diag::ACK) DIAG(F("V%d cv=%d bit=%d"),opcode==V1, ackManagerCv,ackManagerBitNum);
byte instruction = VERIFY_BIT | (opcode==V0?BIT_OFF:BIT_ON) | ackManagerBitNum;
byte message[] = {cv1(BIT_MANIPULATE, ackManagerCv), cv2(ackManagerCv), instruction };
DCCTrack::progTrack.schedulePacket(message, sizeof(message), PROG_REPEATS);
DCCWaveform::progTrack.setAckPending();
}
break;
case WACK: // wait for ack (or absence of ack)
{
byte ackState=2; // keep polling
ackState=DCCWaveform::progTrack.getAck();
if (ackState==2) return; // keep polling
ackReceived=ackState==1;
break; // we have a genuine ACK result
}
case ITC0:
case ITC1: // If True Callback(0 or 1) (if prevous WACK got an ACK)
if (ackReceived) {
callback(opcode==ITC0?0:1);
return;
}
break;
case ITCB: // If True callback(byte)
if (ackReceived) {
callback(ackManagerByte);
return;
}
break;
case ITCBV: // If True callback(byte) - Verify
if (ackReceived) {
if (ackManagerByte == ackManagerByteVerify) {
ackRetrySum ++;
LCD(1, F("v %d %d Sum=%d"), ackManagerCv, ackManagerByte, ackRetrySum);
}
callback(ackManagerByte);
return;
}
break;
case ITCB7: // If True callback(byte & 0x7F)
if (ackReceived) {
callback(ackManagerByte & 0x7F);
return;
}
break;
case NAKFAIL: // If nack callback(-1)
if (!ackReceived) {
callback(-1);
return;
}
break;
case CALLFAIL: // callback(-1)
callback(-1);
return;
case BIV: // ackManagerByte initial value
ackManagerByte = ackManagerByteVerify;
break;
case STARTMERGE:
ackManagerBitNum=7;
ackManagerByte=0;
break;
case MERGE: // Merge previous Validate zero wack response with byte value and update bit number (use for reading CV bytes)
ackManagerByte <<= 1;
// ackReceived means bit is zero.
if (!ackReceived) ackManagerByte |= 1;
ackManagerBitNum--;
break;
case SETBIT:
ackManagerProg++;
ackManagerBitNum=GETFLASH(ackManagerProg);
break;
case SETCV:
ackManagerProg++;
ackManagerCv=GETFLASH(ackManagerProg);
break;
case SETBYTE:
ackManagerProg++;
ackManagerByte=GETFLASH(ackManagerProg);
break;
case SETBYTEH:
ackManagerByte=highByte(ackManagerWord);
break;
case SETBYTEL:
ackManagerByte=lowByte(ackManagerWord);
break;
case STASHLOCOID:
ackManagerStash=ackManagerByte; // stash value from CV17
break;
case COMBINELOCOID:
// ackManagerStash is cv17, ackManagerByte is CV 18
callback( ackManagerByte + ((ackManagerStash - 192) << 8));
return;
case ITSKIP:
if (!ackReceived) break;
// SKIP opcodes until SKIPTARGET found
while (opcode!=SKIPTARGET) {
ackManagerProg++;
opcode=GETFLASH(ackManagerProg);
}
break;
case SKIPTARGET:
break;
default:
DIAG(F("!! ackOp %d FAULT!!"),opcode);
callback( -1);
return;
} // end of switch
ackManagerProg++;
}
}
void DCC::callback(int value) {
// check for automatic retry
if (value == -1 && ackManagerRetry > 0) {
ackRetrySum ++;
LCD(0, F("Retry %d %d Sum=%d"), ackManagerCv, ackManagerRetry, ackRetrySum);
ackManagerRetry --;
ackManagerProg = ackManagerProgStart;
return;
}
static unsigned long callbackStart;
// We are about to leave programming mode
// Rule 1: If we have written to a decoder we must maintain power for 100mS
// Rule 2: If we are re-joining the main track we must power off for 30mS
switch (callbackState) {
case AFTER_WRITE: // first attempt to callback after a write operation
if (!ackManagerRejoin && !DCCWaveform::progTrack.autoPowerOff) {
callbackState=READY;
break;
} // lines 906-910 added. avoid wait after write. use 1 PROG
callbackStart=millis();
callbackState=WAITING_100;
if (Diag::ACK) DIAG(F("Stable 100mS"));
break;
case WAITING_100: // waiting for 100mS
if (millis()-callbackStart < 100) break;
// stable after power maintained for 100mS
// If we are going to power off anyway, it doesnt matter
// but if we will keep the power on, we must off it for 30mS
if (DCCWaveform::progTrack.autoPowerOff) callbackState=READY;
else { // Need to cycle power off and on
DCCWaveform::progTrack.setPowerMode(POWERMODE::OFF);
callbackStart=millis();
callbackState=WAITING_30;
if (Diag::ACK) DIAG(F("OFF 30mS"));
}
break;
case WAITING_30: // waiting for 30mS with power off
if (millis()-callbackStart < 30) break;
//power has been off for 30mS
DCCWaveform::progTrack.setPowerMode(POWERMODE::ON);
callbackState=READY;
break;
case READY: // ready after read, or write after power delay and off period.
// power off if we powered it on
if (DCCWaveform::progTrack.autoPowerOff) {
if (Diag::ACK) DIAG(F("Auto Prog power off"));
DCCWaveform::progTrack.doAutoPowerOff();
}
// Restore <1 JOIN> to state before BASELINE
if (ackManagerRejoin) {
setProgTrackSyncMain(true);
if (Diag::ACK) DIAG(F("Auto JOIN"));
}
ackManagerProg=NULL; // no more steps to execute
if (Diag::ACK) DIAG(F("Callback(%d)"),value);
(ackManagerCallback)( value);
}
}
void DCC::displayCabList(Print * stream) {
int used=0;
for (int reg = 0; reg < MAX_LOCOS; reg++) {
if (speedTable[reg].loco>0) {
used ++;
StringFormatter::send(stream,F("cab=%d, speed=%d, dir=%c \n"),
speedTable[reg].loco, speedTable[reg].speedCode & 0x7f,(speedTable[reg].speedCode & 0x80) ? 'F':'R');
}
}
StringFormatter::send(stream,F("Used=%d, max=%d\n"),used,MAX_LOCOS);
}
View Git Blame Copy Permalink