mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-30 03:26:13 +01:00
89 lines
2.9 KiB
C++
89 lines
2.9 KiB
C++
|
|
|
|
/*!
|
|
* @file PWMServoDriver.cpp
|
|
*
|
|
* @mainpage Adafruit 16-channel PWM & Servo driver, based on Adafruit_PWMServoDriver
|
|
*
|
|
* @section intro_sec Introduction
|
|
*
|
|
* This is a library for the 16-channel PWM & Servo driver.
|
|
*
|
|
* Designed specifically to work with the Adafruit PWM & Servo driver.
|
|
* This class contains a very small subset of the Adafruit version which
|
|
* is relevant to driving simple servos at 50Hz through a number of chained
|
|
* servo driver boards (ie servos 0-15 on board 0x40, 16-31 on board 0x41 etc.)
|
|
*
|
|
* @section author Author
|
|
* Chris Harlow (TPL)
|
|
* original by Limor Fried/Ladyada (Adafruit Industries).
|
|
*
|
|
* @section license License
|
|
*
|
|
* BSD license, all text above must be included in any redistribution
|
|
*/
|
|
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
#include "PWMServoDriver.h"
|
|
#include "DIAG.h"
|
|
|
|
|
|
// REGISTER ADDRESSES
|
|
const byte PCA9685_MODE1=0x00; // Mode Register
|
|
const byte PCA9685_FIRST_SERVO=0x06; /** low byte first servo register ON*/
|
|
const byte PCA9685_PRESCALE=0xFE; /** Prescale register for PWM output frequency */
|
|
// MODE1 bits
|
|
const byte MODE1_SLEEP=0x10; /**< Low power mode. Oscillator off */
|
|
const byte MODE1_AI=0x20; /**< Auto-Increment enabled */
|
|
const byte MODE1_RESTART=0x80; /**< Restart enabled */
|
|
|
|
const byte PCA9685_I2C_ADDRESS=0x40; /** First PCA9685 I2C Slave Address */
|
|
const float FREQUENCY_OSCILLATOR=25000000.0; /** Accurate enough for our purposes */
|
|
const uint8_t PRESCALE_50HZ = (uint8_t)(((FREQUENCY_OSCILLATOR / (50.0 * 4096.0)) + 0.5) - 1);
|
|
|
|
/*!
|
|
* @brief Sets the PWM frequency for a chip to 50Hz for servos
|
|
*/
|
|
|
|
byte PWMServoDriver::setupFlags=0; // boards that have been initialised
|
|
|
|
void PWMServoDriver::setup(int board) {
|
|
if (board>3 || setupFlags & (1<<board)) return;
|
|
Wire.begin();
|
|
uint8_t i2caddr=PCA9685_I2C_ADDRESS + board;
|
|
//DIAG(F("\nPWMServoDriver::setup %x prescale=%d"),i2caddr,PRESCALE_50HZ);
|
|
writeRegister(i2caddr,PCA9685_MODE1, MODE1_SLEEP | MODE1_AI);
|
|
writeRegister(i2caddr,PCA9685_PRESCALE, PRESCALE_50HZ);
|
|
writeRegister(i2caddr,PCA9685_MODE1,MODE1_AI);
|
|
writeRegister(i2caddr,PCA9685_MODE1, MODE1_RESTART | MODE1_AI);
|
|
setupFlags|=1<<board;
|
|
}
|
|
|
|
/*!
|
|
* @brief Sets the PWM output to a servo
|
|
*/
|
|
void PWMServoDriver::setServo(byte servoNum, uint16_t value) {
|
|
//DIAG(F("\nsetServo %d %d\n"),servoNum,value);
|
|
int board=servoNum/16;
|
|
int pin=servoNum%16;
|
|
|
|
if ( board>3) return; // safe dropout
|
|
setup(board); // in case not already done
|
|
|
|
Wire.beginTransmission(PCA9685_I2C_ADDRESS + board);
|
|
Wire.write(PCA9685_FIRST_SERVO + 4 * pin); // 4 registers per pin
|
|
Wire.write(0);
|
|
Wire.write(0);
|
|
Wire.write(value);
|
|
Wire.write(value >> 8);
|
|
Wire.endTransmission();
|
|
}
|
|
|
|
void PWMServoDriver::writeRegister(uint8_t i2caddr,uint8_t hardwareRegister, uint8_t d) {
|
|
Wire.beginTransmission(i2caddr);
|
|
Wire.write(hardwareRegister);
|
|
Wire.write(d);
|
|
Wire.endTransmission();
|
|
delay(5); // allow registers to settle before continuing
|
|
}
|