mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-23 08:06:13 +01:00
268 lines
8.0 KiB
C++
268 lines
8.0 KiB
C++
/*
|
|
* © 2021, Chris Harlow & David Cutting. All rights reserved.
|
|
*
|
|
* This file is part of Asbelos DCC API
|
|
*
|
|
* This is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* It is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with CommandStation. If not, see <https://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
|
|
/* This timer class is used to manage the single timer required to handle the DCC waveform.
|
|
* All timer access comes through this class so that it can be compiled for
|
|
* various hardware CPU types.
|
|
*
|
|
* DCCEX works on a single timer interrupt at a regular 58uS interval.
|
|
* The DCCWaveform class generates the signals to the motor shield
|
|
* based on this timer.
|
|
*
|
|
* If the motor drivers are BOTH configured to use the correct 2 pins for the architecture,
|
|
* (see isPWMPin() function. )
|
|
* then this allows us to use a hardware driven pin switching arrangement which is
|
|
* achieved by setting the duty cycle of the NEXT clock interrupt to 0% or 100% depending on
|
|
* the required pin state. (see setPWM())
|
|
* This is more accurate than the software interrupt but at the expense of
|
|
* limiting the choice of available pins.
|
|
* Fortunately, a standard motor shield on a Mega uses pins that qualify for PWM...
|
|
* Other shields may be jumpered to PWM pins or run directly using the software interrupt.
|
|
*
|
|
* Because the PWM-based waveform is effectively set half a cycle after the software version,
|
|
* it is not acceptable to drive the two tracks on different methiods or it would cause
|
|
* problems for <1 JOIN> etc.
|
|
*
|
|
*/
|
|
|
|
#include "DCCTimer.h"
|
|
const int DCC_SIGNAL_TIME=58; // this is the 58uS DCC 1-bit waveform half-cycle
|
|
const long CLOCK_CYCLES=(F_CPU / 1000000 * DCC_SIGNAL_TIME) >>1;
|
|
|
|
INTERRUPT_CALLBACK interruptHandler=0;
|
|
|
|
#ifdef ARDUINO_ARCH_MEGAAVR
|
|
// Arduino unoWifi Rev2 and nanoEvery architectire
|
|
|
|
void DCCTimer::begin(INTERRUPT_CALLBACK callback) {
|
|
interruptHandler=callback;
|
|
noInterrupts();
|
|
ADC0.CTRLC = (ADC0.CTRLC & 0b00110000) | 0b01000011; // speed up analogRead sample time
|
|
TCB0.CTRLB = TCB_CNTMODE_INT_gc & ~TCB_CCMPEN_bm; // timer compare mode with output disabled
|
|
TCB0.CTRLA = TCB_CLKSEL_CLKDIV2_gc; // 8 MHz ~ 0.125 us
|
|
TCB0.CCMP = CLOCK_CYCLES -1; // 1 tick less for timer reset
|
|
TCB0.INTFLAGS = TCB_CAPT_bm; // clear interrupt request flag
|
|
TCB0.INTCTRL = TCB_CAPT_bm; // Enable the interrupt
|
|
TCB0.CNT = 0;
|
|
TCB0.CTRLA |= TCB_ENABLE_bm; // start
|
|
interrupts();
|
|
}
|
|
|
|
// ISR called by timer interrupt every 58uS
|
|
ISR(TCB0_INT_vect){
|
|
TCB0.INTFLAGS = TCB_CAPT_bm;
|
|
interruptHandler();
|
|
}
|
|
|
|
bool DCCTimer::isPWMPin(byte pin) {
|
|
(void) pin;
|
|
return false; // TODO what are the relevant pins?
|
|
}
|
|
|
|
bool DCCTimer::isPWMPin(byte pin) {
|
|
(void) pin;
|
|
return false; // TODO what are the relevant pins?
|
|
}
|
|
|
|
void DCCTimer::setPWM(byte pin, bool high) {
|
|
(void) pin;
|
|
(void) high;
|
|
// TODO what are the relevant pins?
|
|
}
|
|
|
|
void DCCTimer::getSimulatedMacAddress(byte mac[6]) {
|
|
memcpy(mac,(void *) &SIGROW.SERNUM0,6); // serial number
|
|
mac[0] &= 0xFE;
|
|
mac[0] |= 0x02;
|
|
}
|
|
|
|
#elif defined(TEENSYDUINO)
|
|
IntervalTimer myDCCTimer;
|
|
|
|
void DCCTimer::begin(INTERRUPT_CALLBACK callback) {
|
|
interruptHandler=callback;
|
|
|
|
myDCCTimer.begin(interruptHandler, DCC_SIGNAL_TIME);
|
|
|
|
}
|
|
|
|
bool DCCTimer::isPWMPin(byte pin) {
|
|
//Teensy: digitalPinHasPWM, todo
|
|
(void) pin;
|
|
return false; // TODO what are the relevant pins?
|
|
}
|
|
|
|
bool DCCTimer::isRailcomPin(byte pin) {
|
|
//Teensy: digitalPinHasPWM, todo
|
|
(void) pin;
|
|
return false; // TODO what are the relevant pins?
|
|
}
|
|
|
|
void DCCTimer::setPWM(byte pin, bool high) {
|
|
// TODO what are the relevant pins?
|
|
(void) pin;
|
|
(void) high;
|
|
}
|
|
|
|
void DCCTimer::getSimulatedMacAddress(byte mac[6]) {
|
|
#if defined(__IMXRT1062__) //Teensy 4.0 and Teensy 4.1
|
|
uint32_t m1 = HW_OCOTP_MAC1;
|
|
uint32_t m2 = HW_OCOTP_MAC0;
|
|
mac[0] = m1 >> 8;
|
|
mac[1] = m1 >> 0;
|
|
mac[2] = m2 >> 24;
|
|
mac[3] = m2 >> 16;
|
|
mac[4] = m2 >> 8;
|
|
mac[5] = m2 >> 0;
|
|
#else
|
|
read_mac(mac);
|
|
#endif
|
|
}
|
|
|
|
#if !defined(__IMXRT1062__)
|
|
void DCCTimer::read_mac(byte mac[6]) {
|
|
read(0xe,mac,0);
|
|
read(0xf,mac,3);
|
|
}
|
|
|
|
// http://forum.pjrc.com/threads/91-teensy-3-MAC-address
|
|
void DCCTimer::read(uint8_t word, uint8_t *mac, uint8_t offset) {
|
|
FTFL_FCCOB0 = 0x41; // Selects the READONCE command
|
|
FTFL_FCCOB1 = word; // read the given word of read once area
|
|
|
|
// launch command and wait until complete
|
|
FTFL_FSTAT = FTFL_FSTAT_CCIF;
|
|
while(!(FTFL_FSTAT & FTFL_FSTAT_CCIF));
|
|
|
|
*(mac+offset) = FTFL_FCCOB5; // collect only the top three bytes,
|
|
*(mac+offset+1) = FTFL_FCCOB6; // in the right orientation (big endian).
|
|
*(mac+offset+2) = FTFL_FCCOB7; // Skip FTFL_FCCOB4 as it's always 0.
|
|
}
|
|
#endif
|
|
|
|
#else
|
|
// Arduino nano, uno, mega etc
|
|
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
|
#define TIMER1_A_PIN 11
|
|
#define TIMER1_B_PIN 12
|
|
#define TIMER1_C_PIN 13
|
|
//railcom timer facility
|
|
// #define TIMER4_A_PIN 6
|
|
#define TIMER4_B_PIN 7
|
|
#define TIMER4_C_PIN 8
|
|
#else
|
|
#define TIMER1_A_PIN 9
|
|
#define TIMER1_B_PIN 10
|
|
#endif
|
|
|
|
void DCCTimer::begin(INTERRUPT_CALLBACK callback) {
|
|
interruptHandler=callback;
|
|
noInterrupts();
|
|
ADCSRA = (ADCSRA & 0b11111000) | 0b00000100; // speed up analogRead sample time
|
|
TCCR1A = 0;
|
|
ICR1 = CLOCK_CYCLES;
|
|
TCNT1 = 0;
|
|
TCCR1B = _BV(WGM13) | _BV(CS10); // Mode 8, clock select 1
|
|
TIMSK1 = _BV(TOIE1); // Enable Software interrupt
|
|
|
|
#if defined(TIMER4_A_PIN)
|
|
//railcom timer facility
|
|
TCCR4A = 0;
|
|
ICR4 = CLOCK_CYCLES;
|
|
TCNT4 = CLOCK_CYCLES/2; // this timer fires half cycle after Timer 1
|
|
TCCR4B = _BV(WGM13) | _BV(CS10); // Mode 8, clock select 1
|
|
TIMSK4 = 0; // Disable Software interrupt
|
|
#endif
|
|
|
|
interrupts();
|
|
}
|
|
|
|
// ISR called by timer interrupt every 58uS
|
|
ISR(TIMER1_OVF_vect){ interruptHandler(); }
|
|
|
|
// Alternative pin manipulation via PWM control.
|
|
bool DCCTimer::isPWMPin(byte pin) {
|
|
return pin==TIMER1_A_PIN
|
|
|| pin==TIMER1_B_PIN
|
|
#ifdef TIMER1_C_PIN
|
|
|| pin==TIMER1_C_PIN
|
|
#endif
|
|
;
|
|
}
|
|
// Alternative pin manipulation via PWM control.
|
|
bool DCCTimer::isRailcomPin(byte pin) {
|
|
return
|
|
#ifdef TIMER4_A_PIN
|
|
pin==TIMER4_A_PIN ||
|
|
pin==TIMER4_B_PIN ||
|
|
pin==TIMER4_C_PIN ||
|
|
#endif
|
|
false;
|
|
}
|
|
|
|
void DCCTimer::setPWM(byte pin, bool high) {
|
|
byte val=high?1024:0;
|
|
if (pin==TIMER1_A_PIN) {
|
|
TCCR1A |= _BV(COM1A1);
|
|
OCR1A= val;
|
|
}
|
|
else if (pin==TIMER1_B_PIN) {
|
|
TCCR1A |= _BV(COM1B1);
|
|
OCR1B= val;
|
|
}
|
|
#ifdef TIMER1_C_PIN
|
|
else if (pin==TIMER1_C_PIN) {
|
|
TCCR1A |= _BV(COM1C1);
|
|
OCR1C= val;
|
|
}
|
|
#endif
|
|
#ifdef TIMER4_A_PIN
|
|
else if (pin==TIMER4_A_PIN) {
|
|
TCCR4A |= _BV(COM4A1); //??????????????????????????????????
|
|
OCR4A= val;
|
|
}
|
|
#endif
|
|
#ifdef TIMER4_B_PIN
|
|
else if (pin==TIMER4_B_PIN) {
|
|
TCCR4B |= _BV(COM4B1); //??????????????????????????????????
|
|
OCR4B= val;
|
|
}
|
|
#endif
|
|
#ifdef TIMER4_C_PIN
|
|
else if (pin==TIMER4_C_PIN) {
|
|
TCCR4C |= _BV(COM4C1); //??????????????????????????????????
|
|
OCR4C= val;
|
|
}
|
|
#endif
|
|
}
|
|
|
|
|
|
#include <avr/boot.h>
|
|
void DCCTimer::getSimulatedMacAddress(byte mac[6]) {
|
|
for (byte i=0; i<6; i++) {
|
|
mac[i]=boot_signature_byte_get(0x0E + i);
|
|
}
|
|
mac[0] &= 0xFE;
|
|
mac[0] |= 0x02;
|
|
|
|
}
|
|
|
|
#endif
|