mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-23 08:06:13 +01:00
180 lines
6.5 KiB
C
180 lines
6.5 KiB
C
/**********************************************************************
|
|
|
|
Config.h
|
|
COPYRIGHT (c) 2013-2016 Gregg E. Berman
|
|
COPYRIGHT (c) 2020 Fred Decker
|
|
|
|
The configuration file for DCC++ EX Command Station
|
|
|
|
**********************************************************************/
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
// NOTE: Before connecting these boards and selecting one in this software
|
|
// check the quick install guides!!! Some of these boards require a voltage
|
|
// generating resitor on the current sense pin of the device. Failure to select
|
|
// the correct resistor could damage the sense pin on your Arduino or destroy
|
|
// the device.
|
|
//
|
|
// DEFINE MOTOR_SHIELD_TYPE ACCORDING TO THE FOLLOWING TABLE:
|
|
//
|
|
// STANDARD_MOTOR_SHIELD = ARDUINO MOTOR SHIELD (MAX 18V/2A PER CHANNEL) Arduino Motor shield Rev3 based on the L298
|
|
// POLOLU_MOTOR_SHIELD = POLOLU MC33926 MOTOR SHIELD (MAX 28V/2.5 PER CHANNEL) Pololu MC33926 Motor Driver (shield or carrier)
|
|
// FUNDUMOTO_SHIELD = FunduMoto Motor Shield
|
|
// FIREBOX_MK1 = Firebox MK1
|
|
// FIREBOX_MK1S = Firebox MK1S
|
|
|
|
|
|
#define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE PROGRAM TRACK CURRENT LIMIT IN MILLIAMPS
|
|
|
|
#define TRIP_CURRENT_PROG 250
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// NOTE: Only the Mega currently supports WiFi since space is a constraint on the Uno
|
|
// at this time. It may be implemented in the future.
|
|
//
|
|
//
|
|
//
|
|
// Enable Use of WiFI for the Command Station for DCC-EX communications
|
|
|
|
#define ENABLE_WIFI false
|
|
|
|
#if ENABLE_WIFI
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE WiFi Parameters
|
|
//
|
|
#define WIFI_SSID "Your network name"
|
|
#define WIFI_PASSWORD "Your network passwd"
|
|
#define WIFI_HOSTNAME ""
|
|
#define WIFI_PORT 3252
|
|
|
|
|
|
// This defines the speed at which the Arduino will communicate with the ESP8266 module.
|
|
// When using the ESP8266 on an Uno it is recommended to use 9600, for Mega2560 the
|
|
// higher speed can be used. Set this based on your ESP8266 module configuration.
|
|
// Common defaults are 9600 or 115200.
|
|
#define WIFI_SERIAL_LINK_SPEED 115200
|
|
#endif
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE STATIC IP ADDRESS *OR* COMMENT OUT TO USE DHCP
|
|
//
|
|
|
|
//#define IP_ADDRESS { 192, 168, 1, 200 }
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE PORT TO USE FOR ETHERNET COMMUNICATIONS INTERFACE
|
|
//
|
|
// Uncomment to use Ethernet
|
|
|
|
// #define ETHERNET_PORT 2560
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE MAC ADDRESS ARRAY FOR ETHERNET COMMUNICATIONS INTERFACE
|
|
//
|
|
// Uncomment to use with Ethernet Shields
|
|
//
|
|
// NOTE: This is not used with ESP8266 WiFi modules.
|
|
|
|
// #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xEF }
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Allows using a pin as a trigger for a scope or analyzer so we can capture only
|
|
// the important parts of the data stream
|
|
//
|
|
// USE_TRIGGERPIN: Enable code that switches the trigger pin on and off at end
|
|
// of the preamble. This takes some clock cycles in the
|
|
// interrupt routine for the main track.
|
|
// USE_TRIGGERPIN_PER_BIT: As above but for every bit. This only makes sense
|
|
// if USE_TRIGGERPIN is set.
|
|
//
|
|
// The value of the TRIGGERPIN is defined in DCCppEX.h because it might
|
|
// be board specific
|
|
//
|
|
//#define USE_TRIGGERPIN
|
|
//#define USE_TRIGGERPIN_PER_BIT
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Define only of you need the store to EEPROM feature. This takes RAM and
|
|
// you may need to use less MAX_MAIN_REGISTERS to compensate (at least on the UNO)
|
|
|
|
#define EESTORE
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// This shows the status and version at startup. This takes RAM. You can comment
|
|
// this line if you need to increase MAX_MAIN_REGISTERS(at least on the UNO)
|
|
|
|
#define SHOWCONFIG
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// This is different from the above config display which only shows one line at startup
|
|
// This defines a pin that when jumpered to ground before powering up the Arduinio,
|
|
// will display more detailed settings for diagnostics. You must remove the jumper and
|
|
// restart the Arduino to return to normal operation
|
|
|
|
#define SHOW_CONFIG_DETAIL_PIN A2
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// PREAMBLE_MAIN: Length of the preamble on the main track. Per standard this should
|
|
// be at least 14 bits but if some equipment wants to insert a RailCom
|
|
// cutout this should be at least 16 bits.
|
|
// PERAMBLE_PROG: Length of the preamble on the programming track. Per standard this
|
|
// should be at least 22 bits
|
|
|
|
#define PREAMBLE_MAIN 16 // TODO: Finish configurable preamble code
|
|
#define PREAMBLE_PROG 22
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE LCD SCREEN USAGE BY THE BASE STATION
|
|
//
|
|
// Note: This feature requires an I2C enabled LCD screen using a PCF8574 based chipset.
|
|
// or one using a Hitachi HD44780.
|
|
//
|
|
// To enable, uncomment the line below and make sure only the correct LIB_TYPE line
|
|
// is uncommented below to select the library used for your LCD backpack
|
|
|
|
//#define ENABLE_LCD
|
|
|
|
#ifdef ENABLE_LCD
|
|
#define LIB_TYPE_PCF8574
|
|
//#define LIB_TYPE_I2C
|
|
// This defines the I2C address for the LCD device
|
|
#define LCD_ADDRESS 0x27 //common defaults are 0x27 and 0x3F
|
|
|
|
// This defines the number of columns the LCD device has
|
|
#define LCD_COLUMNS 16
|
|
|
|
// This defines the number of lines the LCD device has
|
|
#define LCD_LINES 2
|
|
#endif
|
|
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Enable custom command filtering
|
|
#define ENABLE_CUSTOM_FILTER false
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Enable custom command filtering
|
|
#define ENABLE_CUSTOM_CALLBACK false
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Enable custom command filtering
|
|
#define ENABLE_FREE_MEM_WARNING false
|