mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-25 00:56:13 +01:00
f348857ddb
FLAGS HAL device added to IODevice.h, which allows use of SET/RESET/<Z>/<T> to set and reset a VPIN state, and to allow <S>/IF/IFNOT/AT/WAITFOR/etc. to monitor the VPIN state. Also, correct handling of VPINs above 32767 in DIAG calls within IODevice.cpp and IODevice.h.
170 lines
6.9 KiB
Plaintext
170 lines
6.9 KiB
Plaintext
/**********************************************************************
|
|
|
|
Config.h
|
|
COPYRIGHT (c) 2013-2016 Gregg E. Berman
|
|
COPYRIGHT (c) 2020 Fred Decker
|
|
|
|
The configuration file for DCC++ EX Command Station
|
|
|
|
**********************************************************************/
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
// NOTE: Before connecting these boards and selecting one in this software
|
|
// check the quick install guides!!! Some of these boards require a voltage
|
|
// generating resitor on the current sense pin of the device. Failure to select
|
|
// the correct resistor could damage the sense pin on your Arduino or destroy
|
|
// the device.
|
|
//
|
|
// DEFINE MOTOR_SHIELD_TYPE BELOW ACCORDING TO THE FOLLOWING TABLE:
|
|
//
|
|
// STANDARD_MOTOR_SHIELD : Arduino Motor shield Rev3 based on the L298 with 18V 2A per channel
|
|
// POLOLU_MOTOR_SHIELD : Pololu MC33926 Motor Driver (not recommended for prog track)
|
|
// FUNDUMOTO_SHIELD : Fundumoto Shield, no current sensing (not recommended, no short protection)
|
|
// FIREBOX_MK1 : The Firebox MK1
|
|
// FIREBOX_MK1S : The Firebox MK1S
|
|
// |
|
|
// +-----------------------v
|
|
//
|
|
// #define STANDARD_MOTOR_SHIELD F("STANDARD_MOTOR_SHIELD"),
|
|
// new MotorDriver(3, 12, UNUSED_PIN, 9, A0, 0.488, 1500, UNUSED_PIN),
|
|
// new MotorDriver(11, 13, UNUSED_PIN, 8, A1, 0.488, 1500, UNUSED_PIN)
|
|
|
|
#define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// The IP port to talk to a WIFI or Ethernet shield.
|
|
//
|
|
#define IP_PORT 2560
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// NOTE: Only supported on Arduino Mega
|
|
// Set to false if you not even want it on the Arduino Mega
|
|
//
|
|
//#define ENABLE_WIFI true
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE WiFi Parameters (only in effect if WIFI is on)
|
|
//
|
|
// If DONT_TOUCH_WIFI_CONF is set, all WIFI config will be done with
|
|
// the <+> commands and this sketch will not change anything over
|
|
// AT commands and the other WIFI_* defines below do not have any effect.
|
|
//#define DONT_TOUCH_WIFI_CONF
|
|
//
|
|
// WIFI_SSID is the network name IF you want to use your existing home network.
|
|
// Do NOT change this if you want to use the WiFi in Access Point (AP) mode.
|
|
//
|
|
// If you do NOT set the WIFI_SSID, the WiFi chip will first try
|
|
// to connect to the previously configured network and if that fails
|
|
// fall back to Access Point mode. The SSID of the AP will be
|
|
// automatically set to DCCEX_*.
|
|
//
|
|
// Your SSID may not conain ``"'' (double quote, ASCII 0x22).
|
|
#define WIFI_SSID "Your network name"
|
|
//
|
|
// WIFI_PASSWORD is the network password for your home network or if
|
|
// you want to change the password from default AP mode password
|
|
// to the AP password you want.
|
|
// Your password may not conain ``"'' (double quote, ASCII 0x22).
|
|
#define WIFI_PASSWORD "deadcafe"
|
|
//
|
|
// WIFI_HOSTNAME: You probably don't need to change this
|
|
#define WIFI_HOSTNAME "dccex"
|
|
//
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// Wifi connect timeout in milliseconds. Default is 14000 (14 seconds). You only need
|
|
// to set this if you have an extremely slow Wifi router.
|
|
//
|
|
#define WIFI_CONNECT_TIMEOUT 14000
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// ENABLE_ETHERNET: Set to true if you have an Arduino Ethernet card (wired). This
|
|
// is not for Wifi. You will then need the Arduino Ethernet library as well
|
|
//
|
|
//#define ENABLE_ETHERNET true
|
|
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE STATIC IP ADDRESS *OR* COMMENT OUT TO USE DHCP
|
|
//
|
|
//#define IP_ADDRESS { 192, 168, 1, 31 }
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE MAC ADDRESS ARRAY FOR ETHERNET COMMUNICATIONS INTERFACE
|
|
//
|
|
// Uncomment to use with Ethernet Shields
|
|
//
|
|
// Ethernet Shields do not have have a MAC address in hardware. There may be one on
|
|
// a sticker on the Shield that you should use. Otherwise choose one of the ones below
|
|
// Be certain that no other device on your network has this same MAC address!
|
|
//
|
|
// 52:b8:8a:8e:ce:21
|
|
// e3:e9:73:e1:db:0d
|
|
// 54:2b:13:52:ac:0c
|
|
|
|
// NOTE: This is not used with ESP8266 WiFi modules.
|
|
|
|
//#define MAC_ADDRESS { 0x52, 0xB8, 0x8A, 0x8E, 0xCE, 0x21 } // MAC address of your networking card found on the sticker on your card or take one from above
|
|
|
|
//
|
|
// #define MAC_ADDRESS { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xEF }
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE LCD SCREEN USAGE BY THE BASE STATION
|
|
//
|
|
// Note: This feature requires an I2C enabled LCD screen using a Hitachi HD44780
|
|
// controller and a PCF8574 based I2C 'backpack',
|
|
// OR an I2C Oled screen based on SSD1306 (128x64 or 128x32) controller,
|
|
// OR an I2C Oled screen based on SH1106 (132x64) controller.
|
|
// To enable, uncomment one of the lines below
|
|
|
|
// define LCD_DRIVER for I2C LCD address 0x3f,16 cols, 2 rows
|
|
//#define LCD_DRIVER {SubBus_4,0x27},20,4
|
|
|
|
//OR define OLED_DRIVER width,height in pixels (address auto detected)
|
|
#if defined(ARDUINO_ARCH_STM32)
|
|
#define OLED_DRIVER 0x3c, 128, 64
|
|
#else
|
|
#define OLED_DRIVER {SubBus_0,0x3c}, 128, 32
|
|
#endif
|
|
|
|
#define SCROLLMODE 1
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
// DISABLE EEPROM
|
|
//
|
|
// If you do not need the EEPROM at all, you can disable all the code that saves
|
|
// data in the EEPROM. You might want to do that if you are in a Arduino UNO
|
|
// and want to use the EX-RAIL automation. Otherwise you do not have enough RAM
|
|
// to do that. Of course, then none of the EEPROM related commands work.
|
|
//
|
|
#define DISABLE_EEPROM
|
|
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|
|
//
|
|
// DEFINE TURNOUTS/ACCESSORIES FOLLOW NORM RCN-213
|
|
//
|
|
// According to norm RCN-213 a DCC packet with a 1 is closed/straight
|
|
// and one with a 0 is thrown/diverging. In DCC++ Classic, and in previous
|
|
// versions of DCC++EX, a turnout throw command was implemented in the packet as
|
|
// '1' and a close command as '0'. The #define below makes the states
|
|
// match with the norm. But we don't want to cause havoc on existent layouts,
|
|
// so we define this only for new installations. If you don't want this,
|
|
// don't add it to your config.h.
|
|
//#define DCC_TURNOUTS_RCN_213
|
|
|
|
// The following #define likewise inverts the behaviour of the <a> command
|
|
// for triggering DCC Accessory Decoders, so that <a addr subaddr 0> generates a
|
|
// DCC packet with D=1 (close turnout) and <a addr subaddr 1> generates D=0
|
|
// (throw turnout).
|
|
//#define DCC_ACCESSORY_RCN_213
|
|
|
|
/////////////////////////////////////////////////////////////////////////////////////
|