mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-12-29 15:11:24 +01:00
74 lines
2.5 KiB
C++
74 lines
2.5 KiB
C++
/*
|
|
* © 2020, Chris Harlow. All rights reserved.
|
|
*
|
|
* This file is a demonstattion of setting up a DCC-EX
|
|
* Command station to support direct connection of WiThrottle devices
|
|
* such as "Engine Driver". If you contriol your layout through JMRI
|
|
* then DON'T connect throttles to this wifi, connect them to JMRI.
|
|
*
|
|
* This is just 3 statements longer than the basic setup.
|
|
*
|
|
* THIS SETUP DOES NOT APPLY TO ARDUINO UNO WITH ONLY A SINGLE SERIAL PORT.
|
|
* REFER TO SEPARATE EXAMPLE.
|
|
*/
|
|
|
|
#include "DCCEX.h"
|
|
|
|
|
|
|
|
// Create a serial command parser... Enables certain diagnostics and commands
|
|
// to be issued from the USB serial console
|
|
// This is NOT intended for JMRI....
|
|
|
|
DCCEXParser serialParser;
|
|
|
|
void setup() {
|
|
|
|
// The main sketch has responsibilities during setup()
|
|
|
|
// Responsibility 1: Start the usb connection for diagnostics
|
|
// This is normally Serial but uses SerialUSB on a SAMD processor
|
|
|
|
Serial.begin(115200);
|
|
|
|
// Responsibility 3: Start the DCC engine.
|
|
// Note: this provides DCC with two motor drivers, main and prog, which handle the motor shield(s)
|
|
// Standard supported devices have pre-configured macros but custome hardware installations require
|
|
// detailed pin mappings and may also require modified subclasses of the MotorDriver to implement specialist logic.
|
|
|
|
// STANDARD_MOTOR_SHIELD, POLOLU_MOTOR_SHIELD, FIREBOX_MK1, FIREBOX_MK1S are pre defined in MotorShields.h
|
|
|
|
// Optionally a Timer number (1..4) may be passed to DCC::begin to override the default Timer1 used for the
|
|
// waveform generation. e.g. DCC::begin(STANDARD_MOTOR_SHIELD,2); to use timer 2
|
|
|
|
DCC::begin(STANDARD_MOTOR_SHIELD);
|
|
|
|
// Start the WiFi interface.
|
|
// NOTE: References to Serial1 are for the serial port used to connect
|
|
// your wifi chip/shield.
|
|
|
|
|
|
Serial1.begin(115200); // BAUD rate of your Wifi chip/shield
|
|
WifiInterface::setup(Serial1,
|
|
F("BTHub5-M6PT"), // Router name
|
|
F("49de8d4862"), // Router password
|
|
F("DCCEX"), // Hostname (ignored by some wifi chip firmware)
|
|
3532); // port (3532 is 0xDCC)
|
|
|
|
}
|
|
|
|
void loop() {
|
|
// The main sketch has responsibilities during loop()
|
|
|
|
// Responsibility 1: Handle DCC background processes
|
|
// (loco reminders and power checks)
|
|
DCC::loop();
|
|
|
|
// Responsibility 2: handle any incoming commands on USB connection
|
|
serialParser.loop(Serial);
|
|
|
|
// Responsibility 3: Optionally handle any incoming WiFi traffic
|
|
WifiInterface::loop();
|
|
|
|
}
|