1
0
mirror of https://github.com/DCC-EX/CommandStation-EX.git synced 2024-12-24 21:21:24 +01:00
CommandStation-EX/SSD1306init.h
Neil McKechnie 79763a3bb8
SH1106 OLED Display Offset Fix (#169)
Correct display offset for SH1106.  The SH1106 supports 132 columns but most displays use 128 column OLED, connected to the middle columns 2-129.
2021-06-10 11:24:44 -04:00

209 lines
8.2 KiB
C

/* Based on Arduino SSD1306Ascii Library, Copyright (C) 2015 by William Greiman
* Modifications (C) 2021 Neil McKechnie
*
* This Library is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This Library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with the Arduino SSD1306Ascii Library. If not, see
* <http://www.gnu.org/licenses/>.
*/
/**
* @file SSD1306init.h
* @brief Display controller initialization commands.
*/
#ifndef SSD1306init_h
#define SSD1306init_h
//------------------------------------------------------------------------------
#ifndef __AVR__
/** Handle AVR flash addressing. */
#define MEM_TYPE
#else // __AVR__
#define MEM_TYPE __attribute__ ((progmem))
#endif // __AVR__
//------------------------------------------------------------------------------
/** Set Lower Column Start Address for Page Addressing Mode. */
#define SSD1306_SETLOWCOLUMN 0x00
/** Set Higher Column Start Address for Page Addressing Mode. */
#define SSD1306_SETHIGHCOLUMN 0x10
/** Set Memory Addressing Mode. */
#define SSD1306_MEMORYMODE 0x20
/** Set display RAM display start line register from 0 - 63. */
#define SSD1306_SETSTARTLINE 0x40
/** Set Display Contrast to one of 256 steps. */
#define SSD1306_SETCONTRAST 0x81
/** Enable or disable charge pump. Follow with 0X14 enable, 0X10 disable. */
#define SSD1306_CHARGEPUMP 0x8D
/** Set Segment Re-map between data column and the segment driver. */
#define SSD1306_SEGREMAP 0xA0
/** Resume display from GRAM content. */
#define SSD1306_DISPLAYALLON_RESUME 0xA4
/** Force display on regardless of GRAM content. */
#define SSD1306_DISPLAYALLON 0xA5
/** Set Normal Display. */
#define SSD1306_NORMALDISPLAY 0xA6
/** Set Inverse Display. */
#define SSD1306_INVERTDISPLAY 0xA7
/** Set Multiplex Ratio from 16 to 63. */
#define SSD1306_SETMULTIPLEX 0xA8
/** Set Display off. */
#define SSD1306_DISPLAYOFF 0xAE
/** Set Display on. */
#define SSD1306_DISPLAYON 0xAF
/**Set GDDRAM Page Start Address. */
#define SSD1306_SETSTARTPAGE 0XB0
/** Set COM output scan direction normal. */
#define SSD1306_COMSCANINC 0xC0
/** Set COM output scan direction reversed. */
#define SSD1306_COMSCANDEC 0xC8
/** Set Display Offset. */
#define SSD1306_SETDISPLAYOFFSET 0xD3
/** Sets COM signals pin configuration to match the OLED panel layout. */
#define SSD1306_SETCOMPINS 0xDA
/** This command adjusts the VCOMH regulator output. */
#define SSD1306_SETVCOMDETECT 0xDB
/** Set Display Clock Divide Ratio/ Oscillator Frequency. */
#define SSD1306_SETDISPLAYCLOCKDIV 0xD5
/** Set Pre-charge Period */
#define SSD1306_SETPRECHARGE 0xD9
/** Deactivate scroll */
#define SSD1306_DEACTIVATE_SCROLL 0x2E
/** No Operation Command. */
#define SSD1306_NOP 0XE3
//------------------------------------------------------------------------------
/** Set Pump voltage value: (30H~33H) 6.4, 7.4, 8.0 (POR), 9.0. */
#define SH1106_SET_PUMP_VOLTAGE 0X30
/** First byte of set charge pump mode */
#define SH1106_SET_PUMP_MODE 0XAD
/** Second byte charge pump on. */
#define SH1106_PUMP_ON 0X8B
/** Second byte charge pump off. */
#define SH1106_PUMP_OFF 0X8A
//------------------------------------------------------------------------------
/**
* @struct DevType
* @brief Device initialization structure.
*/
struct DevType {
/**
* Pointer to initialization command bytes.
*/
const uint8_t* initcmds;
/**
* Number of initialization bytes.
*/
const uint8_t initSize;
/**
* Width of the diaplay in pixels.
*/
const uint8_t lcdWidth;
/**
* Height of the display in pixels.
*/
const uint8_t lcdHeight;
/**
* Column offset RAM to display. Used to pick start column of SH1106.
*/
const uint8_t colOffset;
};
//------------------------------------------------------------------------------
// this section is based on https://github.com/adafruit/Adafruit_SSD1306
/** Initialization commands for a 128x32 SSD1306 oled display. */
static const uint8_t MEM_TYPE Adafruit128x32init[] = {
// Init sequence for Adafruit 128x32 OLED module
0x00, // Set to command mode
SSD1306_DISPLAYOFF,
SSD1306_SETDISPLAYCLOCKDIV, 0x80, // the suggested ratio 0x80
SSD1306_SETMULTIPLEX, 0x1F, // ratio 32
SSD1306_SETDISPLAYOFFSET, 0x0, // no offset
SSD1306_SETSTARTLINE | 0x0, // line #0
SSD1306_CHARGEPUMP, 0x14, // internal vcc
SSD1306_MEMORYMODE, 0x02, // page mode
SSD1306_SEGREMAP | 0x1, // column 127 mapped to SEG0
SSD1306_COMSCANDEC, // column scan direction reversed
SSD1306_SETCOMPINS, 0x02, // sequential COM pins, disable remap
SSD1306_SETCONTRAST, 0x7F, // contrast level 127
SSD1306_SETPRECHARGE, 0xF1, // pre-charge period (1, 15)
SSD1306_SETVCOMDETECT, 0x40, // vcomh regulator level
SSD1306_DISPLAYALLON_RESUME,
SSD1306_NORMALDISPLAY,
SSD1306_DISPLAYON
};
/** Initialize a 128x32 SSD1306 oled display. */
static const DevType MEM_TYPE Adafruit128x32 = {
Adafruit128x32init,
sizeof(Adafruit128x32init),
128,
32,
0
};
//------------------------------------------------------------------------------
// This section is based on https://github.com/adafruit/Adafruit_SSD1306
/** Initialization commands for a 128x64 SSD1306 oled display. */
static const uint8_t MEM_TYPE Adafruit128x64init[] = {
// Init sequence for Adafruit 128x64 OLED module
0x00, // Set to command mode
SSD1306_DISPLAYOFF,
SSD1306_SETDISPLAYCLOCKDIV, 0x80, // the suggested ratio 0x80
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64
SSD1306_SETDISPLAYOFFSET, 0x0, // no offset
SSD1306_SETSTARTLINE | 0x0, // line #0
SSD1306_CHARGEPUMP, 0x14, // internal vcc
SSD1306_MEMORYMODE, 0x02, // page mode
SSD1306_SEGREMAP | 0x1, // column 127 mapped to SEG0
SSD1306_COMSCANDEC, // column scan direction reversed
SSD1306_SETCOMPINS, 0x12, // alt COM pins, disable remap
SSD1306_SETCONTRAST, 0x7F, // contrast level 127
SSD1306_SETPRECHARGE, 0xF1, // pre-charge period (1, 15)
SSD1306_SETVCOMDETECT, 0x40, // vcomh regulator level
SSD1306_DISPLAYALLON_RESUME,
SSD1306_NORMALDISPLAY,
SSD1306_DISPLAYON
};
/** Initialize a 128x64 oled display. */
static const DevType MEM_TYPE Adafruit128x64 = {
Adafruit128x64init,
sizeof(Adafruit128x64init),
128,
64,
0
};
//------------------------------------------------------------------------------
// This section is based on https://github.com/stanleyhuangyc/MultiLCD
/** Initialization commands for a 128x64 SH1106 oled display. */
static const uint8_t MEM_TYPE SH1106_128x64init[] = {
0x00, // Set to command mode
SSD1306_DISPLAYOFF,
SSD1306_SETSTARTPAGE | 0X0, // set page address
SSD1306_SETSTARTLINE | 0x0, // set start line
SSD1306_SETCONTRAST, 0x80, // 128
SSD1306_SEGREMAP | 0X1, // set segment remap
SSD1306_NORMALDISPLAY, // normal / reverse
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64
SH1106_SET_PUMP_MODE, SH1106_PUMP_ON, // set charge pump enable
SH1106_SET_PUMP_VOLTAGE | 0X2, // 8.0 volts
SSD1306_COMSCANDEC, // Com scan direction
SSD1306_SETDISPLAYOFFSET, 0X00, // set display offset
SSD1306_SETDISPLAYCLOCKDIV, 0X80, // set osc division
SSD1306_SETPRECHARGE, 0X1F, // set pre-charge period
SSD1306_SETCOMPINS, 0X12, // set COM pins
SSD1306_SETVCOMDETECT, 0x40, // set vcomh
SSD1306_DISPLAYON
};
/** Initialize a 128x64 oled SH1106 display. */
static const DevType MEM_TYPE SH1106_128x64 = {
SH1106_128x64init,
sizeof(SH1106_128x64init),
128,
64,
2 // SH1106 is a 132x64 controller. Use middle 128 columns.
};
#endif // SSD1306init_h