mirror of
https://github.com/DCC-EX/CommandStation-EX.git
synced 2024-11-26 17:46:14 +01:00
133 lines
5.0 KiB
C++
133 lines
5.0 KiB
C++
////////////////////////////////////////////////////////////////////////////////////
|
|
// © 2020, Chris Harlow. All rights reserved.
|
|
//
|
|
// This file is a demonstattion of setting up a DCC-EX
|
|
// Command station with optional support for direct connection of WiThrottle devices
|
|
// such as "Engine Driver". If you contriol your layout through JMRI
|
|
// then DON'T connect throttles to this wifi, connect them to JMRI.
|
|
//
|
|
// THE WIFI FEATURE IS NOT SUPPORTED ON ARDUINO DEVICES WITH ONLY 2KB RAM.
|
|
////////////////////////////////////////////////////////////////////////////////////
|
|
|
|
#include "config.h"
|
|
#include "DCCEX.h"
|
|
|
|
// Create a serial command parser for the USB connection,
|
|
// This supports JMRI or manual diagnostics and commands
|
|
// to be issued from the USB serial console.
|
|
DCCEXParser serialParser;
|
|
|
|
// (0) Declare NetworkInterfaces
|
|
// NetworkInterface wifi;
|
|
NetworkInterface eth1;
|
|
NetworkInterface eth2;
|
|
// (0) Declared NetworkInterfaces
|
|
|
|
// (1) Start NetworkInterface - HTTP callback
|
|
void httpRequestHandler(ParsedRequest *req, Client* client) {
|
|
DIAG(F("\nParsed Request:"));
|
|
DIAG(F("\nMethod: [%s]"), req->method);
|
|
DIAG(F("\nURI: [%s]"), req->uri);
|
|
DIAG(F("\nHTTP version: [%s]"), req->version);
|
|
DIAG(F("\nParameter count:[%d]\n"), *req->paramCount);
|
|
}
|
|
// (1) End NetworkInterface - HTTP callback
|
|
|
|
void setup()
|
|
{
|
|
// The main sketch has responsibilities during setup()
|
|
|
|
// Responsibility 1: Start the usb connection for diagnostics
|
|
// This is normally Serial but uses SerialUSB on a SAMD processor
|
|
Serial.begin(115200);
|
|
DIAG(F("DCC++ EX v%S"),F(VERSION));
|
|
|
|
CONDITIONAL_LCD_START {
|
|
// This block is ignored if LCD not in use
|
|
LCD(0,F("DCC++ EX v%S"),F(VERSION));
|
|
LCD(1,F("Starting"));
|
|
}
|
|
|
|
// Start the WiFi interface on a MEGA, Uno cannot currently handle WiFi
|
|
|
|
#if WIFI_ON
|
|
WifiInterface::setup(WIFI_SERIAL_LINK_SPEED, F(WIFI_SSID), F(WIFI_PASSWORD), F(WIFI_HOSTNAME), IP_PORT);
|
|
#endif // WIFI_ON
|
|
|
|
// Responsibility 3: Start the DCC engine.
|
|
// Note: this provides DCC with two motor drivers, main and prog, which handle the motor shield(s)
|
|
// Standard supported devices have pre-configured macros but custome hardware installations require
|
|
// detailed pin mappings and may also require modified subclasses of the MotorDriver to implement specialist logic.
|
|
|
|
// STANDARD_MOTOR_SHIELD, POLOLU_MOTOR_SHIELD, FIREBOX_MK1, FIREBOX_MK1S are pre defined in MotorShields.h
|
|
|
|
// Optionally a Timer number (1..4) may be passed to DCC::begin to override the default Timer1 used for the
|
|
// waveform generation. e.g. DCC::begin(STANDARD_MOTOR_SHIELD,2); to use timer 2
|
|
|
|
DCC::begin(MOTOR_SHIELD_TYPE);
|
|
|
|
// (2) Start NetworkInterface - The original WifiInterface is still there but disabled
|
|
|
|
DIAG(F("\nFree RAM before network init: [%d]\n"),freeMemory());
|
|
DIAG(F("\nNetwork Setup In Progress ...\n\n"));
|
|
|
|
// WIFI, TCP on Port 2560, Wifi (ssid/password) has been configured permanetly already on the esp. If
|
|
// the connection fails will go into AP mode
|
|
// wifi.setup(WIFI);
|
|
|
|
// New connection on known ssid / password combo / port can be added as a last parameter other wise the default of 2560
|
|
// will be used. If it passes the connection will be stored as permanent default. If fails will go into AP mode.
|
|
// wifi.setup(WIFI, TCP, F(WIFI_SSID), F(WIFI_PASSWORD), F(WIFI_HOSTNAME));
|
|
// wifi.setup(WIFI, TCP, F(WIFI_SSID), F(WIFI_PASSWORD), F(WIFI_HOSTNAME, 2323)
|
|
|
|
eth1.setup(WIFI, UDPR); // ETHERNET, UDP on Port 2560
|
|
// eth1.setup(ETHERNET, TCP); // ETHERNET, UDP on Port 2560
|
|
// eth2.setup(ETHERNET, TCP, 23); // ETHERNET, TCP on Port 23 for the CLI
|
|
// eth1.setup(ETHERNET, TCP, 8888); // ETHERNET, TCP on Port 8888
|
|
// wifi.setup(WIFI, TCP); // WIFI on Port 2560
|
|
// eth1.setHttpCallback(httpRequestHandler); // HTTP callback
|
|
|
|
DIAG(F("\nNetwork Setup done ...\n"));
|
|
DIAG(F("\nFree RAM after network init: [%d]\n"),freeMemory());
|
|
|
|
// (2) End starting NetworkInterface
|
|
|
|
LCD(1,F("Ready"));
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// The main sketch has responsibilities during loop()
|
|
|
|
// Responsibility 1: Handle DCC background processes
|
|
// (loco reminders and power checks)
|
|
DCC::loop();
|
|
|
|
// Responsibility 2: handle any incoming commands on USB connection
|
|
serialParser.loop(Serial);
|
|
|
|
// Responsibility 3: Optionally handle any incoming WiFi traffic
|
|
#if WIFI_ON
|
|
WifiInterface::loop();
|
|
#endif
|
|
|
|
|
|
// (3) Start Loop NetworkInterface
|
|
NetworkInterface::loop();
|
|
// (3) End Loop NetworkInterface
|
|
|
|
LCDDisplay::loop(); // ignored if LCD not in use
|
|
|
|
// Optionally report any decrease in memory (will automatically trigger on first call)
|
|
#if ENABLE_FREE_MEM_WARNING
|
|
static int ramLowWatermark = 32767; // replaced on first loop
|
|
|
|
int freeNow = freeMemory();
|
|
if (freeNow < ramLowWatermark)
|
|
{
|
|
ramLowWatermark = freeNow;
|
|
LCD(2,F("Free RAM=%5db"), ramLowWatermark);
|
|
}
|
|
#endif
|
|
}
|