Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
/* Based on Arduino SSD1306Ascii Library, Copyright (C) 2015 by William Greiman
|
|
|
|
* Modifications (C) 2021 Neil McKechnie
|
|
|
|
*
|
2021-04-14 22:46:29 +02:00
|
|
|
* This file is part of CommandStation-EX
|
|
|
|
*
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
* This Library is free software: you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
|
|
* (at your option) any later version.
|
|
|
|
*
|
|
|
|
* This Library is distributed in the hope that it will be useful,
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
*
|
|
|
|
* You should have received a copy of the GNU General Public License
|
|
|
|
* along with the Arduino SSD1306Ascii Library. If not, see
|
|
|
|
* <http://www.gnu.org/licenses/>.
|
|
|
|
*/
|
|
|
|
#include "SSD1306Ascii.h"
|
2021-03-31 13:19:55 +02:00
|
|
|
#include "I2CManager.h"
|
|
|
|
#include "FSH.h"
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
|
2021-07-13 22:15:38 +02:00
|
|
|
//==============================================================================
|
|
|
|
// SSD1306/SSD1106 I2C command bytes
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
/** Set Lower Column Start Address for Page Addressing Mode. */
|
|
|
|
static const uint8_t SSD1306_SETLOWCOLUMN = 0x00;
|
|
|
|
/** Set Higher Column Start Address for Page Addressing Mode. */
|
|
|
|
static const uint8_t SSD1306_SETHIGHCOLUMN = 0x10;
|
|
|
|
/** Set Memory Addressing Mode. */
|
|
|
|
static const uint8_t SSD1306_MEMORYMODE = 0x20;
|
|
|
|
/** Set display RAM display start line register from 0 - 63. */
|
|
|
|
static const uint8_t SSD1306_SETSTARTLINE = 0x40;
|
|
|
|
/** Set Display Contrast to one of 256 steps. */
|
|
|
|
static const uint8_t SSD1306_SETCONTRAST = 0x81;
|
|
|
|
/** Enable or disable charge pump. Follow with 0X14 enable, 0X10 disable. */
|
|
|
|
static const uint8_t SSD1306_CHARGEPUMP = 0x8D;
|
|
|
|
/** Set Segment Re-map between data column and the segment driver. */
|
|
|
|
static const uint8_t SSD1306_SEGREMAP = 0xA0;
|
|
|
|
/** Resume display from GRAM content. */
|
|
|
|
static const uint8_t SSD1306_DISPLAYALLON_RESUME = 0xA4;
|
|
|
|
/** Force display on regardless of GRAM content. */
|
|
|
|
static const uint8_t SSD1306_DISPLAYALLON = 0xA5;
|
|
|
|
/** Set Normal Display. */
|
|
|
|
static const uint8_t SSD1306_NORMALDISPLAY = 0xA6;
|
|
|
|
/** Set Inverse Display. */
|
|
|
|
static const uint8_t SSD1306_INVERTDISPLAY = 0xA7;
|
|
|
|
/** Set Multiplex Ratio from 16 to 63. */
|
|
|
|
static const uint8_t SSD1306_SETMULTIPLEX = 0xA8;
|
|
|
|
/** Set Display off. */
|
|
|
|
static const uint8_t SSD1306_DISPLAYOFF = 0xAE;
|
|
|
|
/** Set Display on. */
|
|
|
|
static const uint8_t SSD1306_DISPLAYON = 0xAF;
|
|
|
|
/**Set GDDRAM Page Start Address. */
|
|
|
|
static const uint8_t SSD1306_SETSTARTPAGE = 0xB0;
|
|
|
|
/** Set COM output scan direction normal. */
|
|
|
|
static const uint8_t SSD1306_COMSCANINC = 0xC0;
|
|
|
|
/** Set COM output scan direction reversed. */
|
|
|
|
static const uint8_t SSD1306_COMSCANDEC = 0xC8;
|
|
|
|
/** Set Display Offset. */
|
|
|
|
static const uint8_t SSD1306_SETDISPLAYOFFSET = 0xD3;
|
|
|
|
/** Sets COM signals pin configuration to match the OLED panel layout. */
|
|
|
|
static const uint8_t SSD1306_SETCOMPINS = 0xDA;
|
|
|
|
/** This command adjusts the VCOMH regulator output. */
|
|
|
|
static const uint8_t SSD1306_SETVCOMDETECT = 0xDB;
|
|
|
|
/** Set Display Clock Divide Ratio/ Oscillator Frequency. */
|
|
|
|
static const uint8_t SSD1306_SETDISPLAYCLOCKDIV = 0xD5;
|
|
|
|
/** Set Pre-charge Period */
|
|
|
|
static const uint8_t SSD1306_SETPRECHARGE = 0xD9;
|
|
|
|
/** Deactivate scroll */
|
|
|
|
static const uint8_t SSD1306_DEACTIVATE_SCROLL = 0x2E;
|
|
|
|
/** No Operation Command. */
|
|
|
|
static const uint8_t SSD1306_NOP = 0xE3;
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
/** Set Pump voltage value: (30H~33H) 6.4, 7.4, 8.0 (POR), 9.0. */
|
|
|
|
static const uint8_t SH1106_SET_PUMP_VOLTAGE = 0x30;
|
|
|
|
/** First byte of set charge pump mode */
|
|
|
|
static const uint8_t SH1106_SET_PUMP_MODE = 0xAD;
|
|
|
|
/** Second byte charge pump on. */
|
|
|
|
static const uint8_t SH1106_PUMP_ON = 0x8B;
|
|
|
|
/** Second byte charge pump off. */
|
|
|
|
static const uint8_t SH1106_PUMP_OFF = 0x8A;
|
|
|
|
//------------------------------------------------------------------------------
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
|
2021-07-13 22:15:38 +02:00
|
|
|
// Sequence of blank pixels, to optimise clearing screen.
|
|
|
|
// Send a maximum of 30 pixels per transmission.
|
|
|
|
const uint8_t FLASH SSD1306AsciiWire::blankPixels[30] =
|
2021-03-31 13:19:55 +02:00
|
|
|
{0x40, // First byte specifies data mode
|
2021-07-13 22:15:38 +02:00
|
|
|
0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
|
2021-03-31 13:19:55 +02:00
|
|
|
|
2021-11-24 13:53:03 +01:00
|
|
|
|
|
|
|
//==============================================================================
|
|
|
|
// this section is based on https://github.com/adafruit/Adafruit_SSD1306
|
|
|
|
|
|
|
|
/** Initialization commands for a 128x32 or 128x64 SSD1306 oled display. */
|
|
|
|
const uint8_t FLASH SSD1306AsciiWire::Adafruit128xXXinit[] = {
|
|
|
|
// Init sequence for Adafruit 128x32/64 OLED module
|
|
|
|
0x00, // Set to command mode
|
|
|
|
SSD1306_DISPLAYOFF,
|
|
|
|
SSD1306_SETDISPLAYCLOCKDIV, 0x80, // the suggested ratio 0x80
|
|
|
|
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64 (initially)
|
|
|
|
SSD1306_SETDISPLAYOFFSET, 0x0, // no offset
|
|
|
|
SSD1306_SETSTARTLINE | 0x0, // line #0
|
|
|
|
SSD1306_CHARGEPUMP, 0x14, // internal vcc
|
|
|
|
SSD1306_MEMORYMODE, 0x02, // page mode
|
|
|
|
SSD1306_SEGREMAP | 0x1, // column 127 mapped to SEG0
|
|
|
|
SSD1306_COMSCANDEC, // column scan direction reversed
|
|
|
|
SSD1306_SETCOMPINS, 0X12, // set COM pins
|
|
|
|
SSD1306_SETCONTRAST, 0x7F, // contrast level 127
|
|
|
|
SSD1306_SETPRECHARGE, 0xF1, // pre-charge period (1, 15)
|
|
|
|
SSD1306_SETVCOMDETECT, 0x40, // vcomh regulator level
|
|
|
|
SSD1306_DISPLAYALLON_RESUME,
|
|
|
|
SSD1306_NORMALDISPLAY,
|
|
|
|
SSD1306_DISPLAYON
|
|
|
|
};
|
|
|
|
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
// This section is based on https://github.com/stanleyhuangyc/MultiLCD
|
|
|
|
|
|
|
|
/** Initialization commands for a 128x64 SH1106 oled display. */
|
|
|
|
const uint8_t FLASH SSD1306AsciiWire::SH1106_132x64init[] = {
|
|
|
|
0x00, // Set to command mode
|
|
|
|
SSD1306_DISPLAYOFF,
|
|
|
|
SSD1306_SETDISPLAYCLOCKDIV, 0X80, // set osc division
|
|
|
|
SSD1306_SETMULTIPLEX, 0x3F, // ratio 64
|
|
|
|
SSD1306_SETDISPLAYOFFSET, 0X00, // set display offset
|
|
|
|
SSD1306_SETSTARTPAGE | 0X0, // set page address
|
|
|
|
SSD1306_SETSTARTLINE | 0x0, // set start line
|
|
|
|
SH1106_SET_PUMP_MODE, SH1106_PUMP_ON, // set charge pump enable
|
|
|
|
SSD1306_SEGREMAP | 0X1, // set segment remap
|
|
|
|
SSD1306_COMSCANDEC, // Com scan direction
|
|
|
|
SSD1306_SETCOMPINS, 0X12, // set COM pins
|
|
|
|
SSD1306_SETCONTRAST, 0x80, // 128
|
|
|
|
SSD1306_SETPRECHARGE, 0X1F, // set pre-charge period
|
|
|
|
SSD1306_SETVCOMDETECT, 0x40, // set vcomh
|
|
|
|
SH1106_SET_PUMP_VOLTAGE | 0X2, // 8.0 volts
|
|
|
|
SSD1306_NORMALDISPLAY, // normal / reverse
|
|
|
|
SSD1306_DISPLAYON
|
|
|
|
};
|
|
|
|
|
2021-03-31 13:19:55 +02:00
|
|
|
//==============================================================================
|
|
|
|
// SSD1306AsciiWire Method Definitions
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
//------------------------------------------------------------------------------
|
2021-07-13 22:15:38 +02:00
|
|
|
|
2023-02-19 20:14:15 +01:00
|
|
|
// Auto-detect address
|
|
|
|
SSD1306AsciiWire::SSD1306AsciiWire(int width, int height)
|
|
|
|
: SSD1306AsciiWire(0, width, height) { }
|
2023-02-05 00:57:22 +01:00
|
|
|
|
2023-02-19 20:14:15 +01:00
|
|
|
// Constructor with explicit address
|
2023-02-16 17:41:13 +01:00
|
|
|
SSD1306AsciiWire::SSD1306AsciiWire(I2CAddress address, int width, int height) {
|
|
|
|
m_i2cAddr = address;
|
|
|
|
m_displayWidth = width;
|
|
|
|
m_displayHeight = height;
|
2023-02-19 20:14:15 +01:00
|
|
|
// Set size in characters
|
|
|
|
m_charsPerColumn = m_displayHeight / fontHeight;
|
|
|
|
m_charsPerRow = (m_displayWidth+fontWidth-1) / fontWidth; // Round up
|
2023-02-16 17:41:13 +01:00
|
|
|
}
|
|
|
|
|
|
|
|
bool SSD1306AsciiWire::begin() {
|
2023-02-05 00:57:22 +01:00
|
|
|
I2CManager.begin();
|
2024-07-10 14:50:33 +02:00
|
|
|
I2CManager.setClock(400000L); // Set max supported I2C speed
|
|
|
|
|
|
|
|
#if defined(OLED_HAS_RESET_PIN)
|
|
|
|
pinMode(OLED_HAS_RESET_PIN, OUTPUT);
|
|
|
|
digitalWrite(OLED_HAS_RESET_PIN, LOW);
|
|
|
|
delay(1);
|
|
|
|
digitalWrite(OLED_HAS_RESET_PIN, HIGH);
|
|
|
|
#endif
|
2023-02-16 17:41:13 +01:00
|
|
|
|
|
|
|
if (m_i2cAddr == 0) {
|
|
|
|
// Probe for I2C device on 0x3c and 0x3d.
|
|
|
|
for (uint8_t address = 0x3c; address <= 0x3d; address++) {
|
|
|
|
if (I2CManager.exists(address)) {
|
|
|
|
m_i2cAddr = address;
|
|
|
|
break;
|
|
|
|
}
|
2023-02-05 00:57:22 +01:00
|
|
|
}
|
2023-02-16 17:41:13 +01:00
|
|
|
if (m_i2cAddr == 0)
|
|
|
|
DIAG(F("OLED display not found"));
|
2023-02-05 00:57:22 +01:00
|
|
|
}
|
|
|
|
|
2021-11-24 13:53:03 +01:00
|
|
|
m_col = 0;
|
|
|
|
m_row = 0;
|
|
|
|
m_colOffset = 0;
|
2021-07-13 22:15:38 +02:00
|
|
|
|
2023-02-05 00:57:22 +01:00
|
|
|
if (m_displayWidth==132 && m_displayHeight==64) {
|
|
|
|
// SH1106 display. This uses 128x64 centered within a 132x64 OLED.
|
|
|
|
m_colOffset = 2;
|
|
|
|
I2CManager.write_P(m_i2cAddr, SH1106_132x64init, sizeof(SH1106_132x64init));
|
|
|
|
} else if (m_displayWidth==128 && (m_displayHeight==64 || m_displayHeight==32)) {
|
2023-02-16 17:41:13 +01:00
|
|
|
// SSD1306 or SSD1309 128x64 or 128x32
|
2023-02-05 00:57:22 +01:00
|
|
|
I2CManager.write_P(m_i2cAddr, Adafruit128xXXinit, sizeof(Adafruit128xXXinit));
|
|
|
|
if (m_displayHeight == 32)
|
|
|
|
I2CManager.write(m_i2cAddr, 5, 0, // Set command mode
|
|
|
|
SSD1306_SETMULTIPLEX, 0x1F, // ratio 32
|
|
|
|
SSD1306_SETCOMPINS, 0x02); // sequential COM pins, disable remap
|
|
|
|
} else {
|
|
|
|
DIAG(F("OLED configuration option not recognised"));
|
|
|
|
return false;
|
2021-07-13 22:15:38 +02:00
|
|
|
}
|
2023-02-05 00:57:22 +01:00
|
|
|
// Device found
|
2023-02-09 01:16:06 +01:00
|
|
|
DIAG(F("%dx%d OLED display configured on I2C:%s"), m_displayWidth, m_displayHeight, m_i2cAddr.toString());
|
2023-02-05 00:57:22 +01:00
|
|
|
return true;
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
}
|
2021-07-13 22:15:38 +02:00
|
|
|
|
|
|
|
/* Clear screen by writing blank pixels. */
|
|
|
|
void SSD1306AsciiWire::clearNative() {
|
2023-02-16 17:41:13 +01:00
|
|
|
const int maxBytes = sizeof(blankPixels) - 1; // max number of pixel columns (bytes) per transmission
|
2021-07-13 22:15:38 +02:00
|
|
|
for (uint8_t r = 0; r <= m_displayHeight/8 - 1; r++) {
|
|
|
|
setRowNative(r); // Position at start of row to be erased
|
2023-02-16 17:41:13 +01:00
|
|
|
for (uint8_t c = 0; c < m_displayWidth; c += maxBytes) {
|
|
|
|
uint8_t len = m_displayWidth-c; // Number of pixel columns remaining
|
2023-02-07 18:09:17 +01:00
|
|
|
if (len > maxBytes) len = maxBytes;
|
2023-02-16 17:41:13 +01:00
|
|
|
I2CManager.write_P(m_i2cAddr, blankPixels, len+1); // Write command + 'len' blank columns
|
2021-03-31 13:19:55 +02:00
|
|
|
}
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
}
|
|
|
|
}
|
2021-07-13 22:15:38 +02:00
|
|
|
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
//------------------------------------------------------------------------------
|
2021-07-13 22:15:38 +02:00
|
|
|
|
|
|
|
// Set cursor position (by text line)
|
|
|
|
void SSD1306AsciiWire::setRowNative(uint8_t line) {
|
|
|
|
// Calculate pixel position from line number
|
|
|
|
uint8_t row = line*8;
|
|
|
|
if (row < m_displayHeight) {
|
2021-03-31 13:19:55 +02:00
|
|
|
m_row = row;
|
2021-07-13 22:15:38 +02:00
|
|
|
m_col = m_colOffset;
|
2021-08-03 23:12:25 +02:00
|
|
|
// Before using buffer, wait for last request to complete
|
|
|
|
requestBlock.wait();
|
2021-07-13 22:15:38 +02:00
|
|
|
// Build output buffer for I2C
|
|
|
|
uint8_t len = 0;
|
|
|
|
outputBuffer[len++] = 0x00; // Set to command mode
|
|
|
|
outputBuffer[len++] = SSD1306_SETLOWCOLUMN | (m_col & 0XF);
|
|
|
|
outputBuffer[len++] = SSD1306_SETHIGHCOLUMN | (m_col >> 4);
|
|
|
|
outputBuffer[len++] = SSD1306_SETSTARTPAGE | (m_row/8);
|
2021-08-03 23:12:25 +02:00
|
|
|
I2CManager.write(m_i2cAddr, outputBuffer, len, &requestBlock);
|
2021-03-31 13:19:55 +02:00
|
|
|
}
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
}
|
|
|
|
//------------------------------------------------------------------------------
|
2021-07-13 22:15:38 +02:00
|
|
|
|
|
|
|
// Write a character to the OLED
|
|
|
|
size_t SSD1306AsciiWire::writeNative(uint8_t ch) {
|
|
|
|
const uint8_t* base = m_font;
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
|
2021-07-13 22:15:38 +02:00
|
|
|
#if defined(NOLOWERCASE)
|
|
|
|
// Adjust if lowercase is missing
|
|
|
|
if (ch >= 'a') {
|
|
|
|
if (ch <= 'z')
|
|
|
|
ch = ch - 'a' + 'A'; // Capitalise
|
|
|
|
else
|
|
|
|
ch -= 26; // Allow for missing lowercase letters
|
|
|
|
}
|
|
|
|
#endif
|
2023-02-25 12:42:43 +01:00
|
|
|
if (ch < m_fontFirstChar || ch >= (m_fontFirstChar + m_fontCharCount))
|
|
|
|
return 0;
|
|
|
|
// Check if character would be partly or wholly off the display
|
|
|
|
if (m_col + fontWidth > m_displayWidth)
|
|
|
|
return 0;
|
|
|
|
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
ch -= m_fontFirstChar;
|
|
|
|
base += fontWidth * ch;
|
2021-08-03 23:12:25 +02:00
|
|
|
// Before using buffer, wait for last request to complete
|
|
|
|
requestBlock.wait();
|
2021-07-13 22:15:38 +02:00
|
|
|
// Build output buffer for I2C
|
|
|
|
outputBuffer[0] = 0x40; // set SSD1306 controller to data mode
|
2021-03-31 13:19:55 +02:00
|
|
|
uint8_t bufferPos = 1;
|
|
|
|
// Copy character pixel columns
|
2023-02-16 17:41:13 +01:00
|
|
|
for (uint8_t i = 0; i < fontWidth; i++) {
|
|
|
|
if (m_col++ < m_displayWidth)
|
|
|
|
outputBuffer[bufferPos++] = GETFLASH(base++);
|
|
|
|
}
|
2021-07-13 22:15:38 +02:00
|
|
|
|
2021-03-31 13:19:55 +02:00
|
|
|
// Write the data to I2C display
|
2021-08-03 23:12:25 +02:00
|
|
|
I2CManager.write(m_i2cAddr, outputBuffer, bufferPos, &requestBlock);
|
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
|
|
|
return 1;
|
|
|
|
}
|
2021-07-13 22:15:38 +02:00
|
|
|
|
|
|
|
|
|
|
|
//------------------------------------------------------------------------------
|
|
|
|
|
2023-02-16 17:41:13 +01:00
|
|
|
// Font characters, 6x8 pixels, starting at 0x20.
|
2021-07-13 22:15:38 +02:00
|
|
|
// Lower case characters optionally omitted.
|
2023-02-16 17:41:13 +01:00
|
|
|
const uint8_t FLASH SSD1306AsciiWire::System6x8[] = {
|
2021-07-13 22:15:38 +02:00
|
|
|
|
|
|
|
// Fixed width; char width table not used !!!!
|
|
|
|
|
|
|
|
// font data
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // (space) (20)
|
|
|
|
0x00, 0x00, 0x5F, 0x00, 0x00, 0x00, // ! (21)
|
|
|
|
0x00, 0x07, 0x00, 0x07, 0x00, 0x00, // "
|
|
|
|
0x14, 0x7F, 0x14, 0x7F, 0x14, 0x00, // #
|
|
|
|
0x24, 0x2A, 0x7F, 0x2A, 0x12, 0x00, // $
|
|
|
|
0x23, 0x13, 0x08, 0x64, 0x62, 0x00, // %
|
|
|
|
0x36, 0x49, 0x55, 0x22, 0x50, 0x00, // &
|
|
|
|
0x00, 0x05, 0x03, 0x00, 0x00, 0x00, // '
|
|
|
|
0x00, 0x1C, 0x22, 0x41, 0x00, 0x00, // (
|
|
|
|
0x00, 0x41, 0x22, 0x1C, 0x00, 0x00, // )
|
|
|
|
0x08, 0x2A, 0x1C, 0x2A, 0x08, 0x00, // *
|
|
|
|
0x08, 0x08, 0x3E, 0x08, 0x08, 0x00, // +
|
|
|
|
0x00, 0x50, 0x30, 0x00, 0x00, 0x00, // ,
|
|
|
|
0x08, 0x08, 0x08, 0x08, 0x08, 0x00, // -
|
|
|
|
0x00, 0x60, 0x60, 0x00, 0x00, 0x00, // .
|
|
|
|
0x20, 0x10, 0x08, 0x04, 0x02, 0x00, // / (47)
|
|
|
|
0x3E, 0x51, 0x49, 0x45, 0x3E, 0x00, // 0 (48)
|
|
|
|
0x00, 0x42, 0x7F, 0x40, 0x00, 0x00, // 1
|
|
|
|
0x42, 0x61, 0x51, 0x49, 0x46, 0x00, // 2
|
|
|
|
0x21, 0x41, 0x45, 0x4B, 0x31, 0x00, // 3
|
|
|
|
0x18, 0x14, 0x12, 0x7F, 0x10, 0x00, // 4
|
|
|
|
0x27, 0x45, 0x45, 0x45, 0x39, 0x00, // 5
|
|
|
|
0x3C, 0x4A, 0x49, 0x49, 0x30, 0x00, // 6
|
|
|
|
0x01, 0x71, 0x09, 0x05, 0x03, 0x00, // 7
|
|
|
|
0x36, 0x49, 0x49, 0x49, 0x36, 0x00, // 8
|
|
|
|
0x06, 0x49, 0x49, 0x29, 0x1E, 0x00, // 9 (57)
|
|
|
|
0x00, 0x36, 0x36, 0x00, 0x00, 0x00, // :
|
|
|
|
0x00, 0x56, 0x36, 0x00, 0x00, 0x00, // ;
|
|
|
|
0x00, 0x08, 0x14, 0x22, 0x41, 0x00, // <
|
|
|
|
0x14, 0x14, 0x14, 0x14, 0x14, 0x00, // =
|
|
|
|
0x41, 0x22, 0x14, 0x08, 0x00, 0x00, // >
|
|
|
|
0x02, 0x01, 0x51, 0x09, 0x06, 0x00, // ?
|
|
|
|
0x32, 0x49, 0x79, 0x41, 0x3E, 0x00, // @ (64)
|
|
|
|
0x7E, 0x11, 0x11, 0x11, 0x7E, 0x00, // A (65)
|
|
|
|
0x7F, 0x49, 0x49, 0x49, 0x36, 0x00, // B
|
|
|
|
0x3E, 0x41, 0x41, 0x41, 0x22, 0x00, // C
|
|
|
|
0x7F, 0x41, 0x41, 0x22, 0x1C, 0x00, // D
|
|
|
|
0x7F, 0x49, 0x49, 0x49, 0x41, 0x00, // E
|
|
|
|
0x7F, 0x09, 0x09, 0x01, 0x01, 0x00, // F
|
|
|
|
0x3E, 0x41, 0x41, 0x51, 0x32, 0x00, // G
|
|
|
|
0x7F, 0x08, 0x08, 0x08, 0x7F, 0x00, // H
|
|
|
|
0x00, 0x41, 0x7F, 0x41, 0x00, 0x00, // I
|
|
|
|
0x20, 0x40, 0x41, 0x3F, 0x01, 0x00, // J
|
|
|
|
0x7F, 0x08, 0x14, 0x22, 0x41, 0x00, // K
|
|
|
|
0x7F, 0x40, 0x40, 0x40, 0x40, 0x00, // L
|
|
|
|
0x7F, 0x02, 0x04, 0x02, 0x7F, 0x00, // M
|
|
|
|
0x7F, 0x04, 0x08, 0x10, 0x7F, 0x00, // N
|
|
|
|
0x3E, 0x41, 0x41, 0x41, 0x3E, 0x00, // O
|
|
|
|
0x7F, 0x09, 0x09, 0x09, 0x06, 0x00, // P
|
|
|
|
0x3E, 0x41, 0x51, 0x21, 0x5E, 0x00, // Q
|
|
|
|
0x7F, 0x09, 0x19, 0x29, 0x46, 0x00, // R
|
|
|
|
0x46, 0x49, 0x49, 0x49, 0x31, 0x00, // S
|
|
|
|
0x01, 0x01, 0x7F, 0x01, 0x01, 0x00, // T
|
|
|
|
0x3F, 0x40, 0x40, 0x40, 0x3F, 0x00, // U
|
|
|
|
0x1F, 0x20, 0x40, 0x20, 0x1F, 0x00, // V
|
|
|
|
0x7F, 0x20, 0x18, 0x20, 0x7F, 0x00, // W
|
|
|
|
0x63, 0x14, 0x08, 0x14, 0x63, 0x00, // X
|
|
|
|
0x03, 0x04, 0x78, 0x04, 0x03, 0x00, // Y
|
|
|
|
0x61, 0x51, 0x49, 0x45, 0x43, 0x00, // Z (90)
|
|
|
|
0x00, 0x00, 0x7F, 0x41, 0x41, 0x00, // [
|
|
|
|
0x02, 0x04, 0x08, 0x10, 0x20, 0x00, // "\"
|
|
|
|
0x41, 0x41, 0x7F, 0x00, 0x00, 0x00, // ]
|
|
|
|
0x04, 0x02, 0x01, 0x02, 0x04, 0x00, // ^
|
|
|
|
0x40, 0x40, 0x40, 0x40, 0x40, 0x00, // _
|
|
|
|
0x00, 0x01, 0x02, 0x04, 0x00, 0x00, // ' (96)
|
2021-07-13 22:15:38 +02:00
|
|
|
#ifndef NOLOWERCASE
|
2023-02-16 17:41:13 +01:00
|
|
|
0x20, 0x54, 0x54, 0x54, 0x78, 0x00, // a (97)
|
|
|
|
0x7F, 0x48, 0x44, 0x44, 0x38, 0x00, // b
|
|
|
|
0x38, 0x44, 0x44, 0x44, 0x20, 0x00, // c
|
|
|
|
0x38, 0x44, 0x44, 0x48, 0x7F, 0x00, // d
|
|
|
|
0x38, 0x54, 0x54, 0x54, 0x18, 0x00, // e
|
|
|
|
0x08, 0x7E, 0x09, 0x01, 0x02, 0x00, // f
|
|
|
|
0x08, 0x14, 0x54, 0x54, 0x3C, 0x00, // g
|
|
|
|
0x7F, 0x08, 0x04, 0x04, 0x78, 0x00, // h
|
|
|
|
0x00, 0x44, 0x7D, 0x40, 0x00, 0x00, // i
|
|
|
|
0x20, 0x40, 0x44, 0x3D, 0x00, 0x00, // j
|
|
|
|
0x00, 0x7F, 0x10, 0x28, 0x44, 0x00, // k
|
|
|
|
0x00, 0x41, 0x7F, 0x40, 0x00, 0x00, // l
|
|
|
|
0x7C, 0x04, 0x18, 0x04, 0x78, 0x00, // m
|
|
|
|
0x7C, 0x08, 0x04, 0x04, 0x78, 0x00, // n
|
|
|
|
0x38, 0x44, 0x44, 0x44, 0x38, 0x00, // o
|
|
|
|
0x7C, 0x14, 0x14, 0x14, 0x08, 0x00, // p
|
|
|
|
0x08, 0x14, 0x14, 0x18, 0x7C, 0x00, // q
|
|
|
|
0x7C, 0x08, 0x04, 0x04, 0x08, 0x00, // r
|
|
|
|
0x48, 0x54, 0x54, 0x54, 0x20, 0x00, // s
|
|
|
|
0x04, 0x3F, 0x44, 0x40, 0x20, 0x00, // t
|
|
|
|
0x3C, 0x40, 0x40, 0x20, 0x7C, 0x00, // u
|
|
|
|
0x1C, 0x20, 0x40, 0x20, 0x1C, 0x00, // v
|
|
|
|
0x3C, 0x40, 0x30, 0x40, 0x3C, 0x00, // w
|
|
|
|
0x44, 0x28, 0x10, 0x28, 0x44, 0x00, // x
|
|
|
|
0x0C, 0x50, 0x50, 0x50, 0x3C, 0x00, // y
|
|
|
|
0x44, 0x64, 0x54, 0x4C, 0x44, 0x00, // z (122)
|
2021-07-13 22:15:38 +02:00
|
|
|
#endif
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x08, 0x36, 0x41, 0x00, 0x00, // { (123)
|
|
|
|
0x00, 0x00, 0x7F, 0x00, 0x00, 0x00, // |
|
|
|
|
0x00, 0x41, 0x36, 0x08, 0x00, 0x00, // }
|
|
|
|
0x08, 0x08, 0x2A, 0x1C, 0x08, 0x00, // ->
|
|
|
|
0x08, 0x1C, 0x2A, 0x08, 0x08, 0x00, // <- (127)
|
|
|
|
#ifndef NO_EXTENDED_CHARACTERS
|
|
|
|
// Extended characters - based on "DOS Western Europe" characters
|
|
|
|
// International characters not yet implemented.
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented 0x80
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented 0x90
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
2023-02-25 12:42:43 +01:00
|
|
|
0x38, 0x44, 0xc6, 0x44, 0x20, 0x00, // cent 0x9b
|
|
|
|
0x44, 0x6e, 0x59, 0x49, 0x62, 0x00, // £ 0x9c
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented 0xa0
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
2023-02-25 12:42:43 +01:00
|
|
|
0x10, 0x28, 0x54, 0x28, 0x44, 0x00, // <<
|
|
|
|
0x44, 0x28, 0x54, 0x28, 0x10, 0x00, // >>
|
2023-02-16 17:41:13 +01:00
|
|
|
// Extended characters 176-180
|
|
|
|
0x92, 0x00, 0x49, 0x00, 0x24, 0x00, // Light grey 0xb0
|
2023-02-25 12:42:43 +01:00
|
|
|
0xaa, 0x44, 0xaa, 0x11, 0xaa, 0x55, // Mid grey 0xb1
|
|
|
|
0x6d, 0xff, 0xb6, 0xff, 0xdb, 0xff, // Dark grey 0xb2
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x00, 0x00, 0xff, 0x00, 0x00, // Vertical line 0xb3
|
|
|
|
0x08, 0x08, 0x08, 0xff, 0x00, 0x00, // Vertical line with left spur 0xb4
|
|
|
|
|
2023-02-25 12:42:43 +01:00
|
|
|
0x14, 0x14, 0x14, 0xff, 0x00, 0x00, // Vertical line with double left spur 0xb5
|
|
|
|
0x08, 0x08, 0xff, 0x00, 0xff, 0x00, // Double vertical line with single left spur
|
|
|
|
0x08, 0x08, 0xf8, 0x08, 0xf8, 0x00, // Top right corner, single horiz, double vert
|
|
|
|
0x14, 0x14, 0x14, 0xfc, 0x00, 0x00, // Top right corner, double horiz, single vert
|
2023-02-16 17:41:13 +01:00
|
|
|
|
|
|
|
// Extended characters 185-190
|
2023-02-25 12:42:43 +01:00
|
|
|
0x14, 0x14, 0xf7, 0x00, 0xff, 0x00, // Double vertical line with double left spur 0xb9
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x00, 0xff, 0x00, 0xff, 0x00, // Double vertical line 0xba
|
|
|
|
0x14, 0x14, 0xf4, 0x04, 0xfc, 0x00, // Double top right corner 0xbb
|
|
|
|
0x14, 0x14, 0x17, 0x10, 0x1f, 0x00, // Double bottom right corner 0xbc
|
2023-02-25 12:42:43 +01:00
|
|
|
0x08, 0x08, 0x0f, 0x08, 0x0f, 0x00, // Bottom right corner, single horiz, double vert 0xbd
|
|
|
|
0x14, 0x14, 0x14, 0x1f, 0x00, 0x00, // Bottom right corner, double horiz, single vert 0xbe
|
2021-07-13 22:15:38 +02:00
|
|
|
|
2023-02-16 17:41:13 +01:00
|
|
|
// Extended characters 191-199
|
|
|
|
0x08, 0x08, 0x08, 0xf8, 0x00, 0x00, // Top right corner 0xbf
|
|
|
|
0x00, 0x00, 0x00, 0x0f, 0x08, 0x08, // Bottom left corner 0xc0
|
|
|
|
0x08, 0x08, 0x08, 0x0f, 0x08, 0x08, // Horizontal line with upward spur 0xc1
|
|
|
|
0x08, 0x08, 0x08, 0xf8, 0x08, 0x08, // Horizontal line with downward spur 0xc2
|
|
|
|
0x00, 0x00, 0x00, 0xff, 0x08, 0x08, // Vertical line with right spur 0xc3
|
|
|
|
0x08, 0x08, 0x08, 0x08, 0x08, 0x08, // Horizontal line 0xc4
|
|
|
|
0x08, 0x08, 0x08, 0xff, 0x08, 0x08, // Cross 0xc5
|
2023-02-25 12:42:43 +01:00
|
|
|
0x00, 0x00, 0x00, 0xff, 0x14, 0x14, // Vertical line double right spur 0xc6
|
|
|
|
0x00, 0x00, 0xff, 0x00, 0xff, 0x08, // Double vertical line single right spur 0xc7
|
2023-02-16 17:41:13 +01:00
|
|
|
|
|
|
|
// Extended characters 200-206
|
|
|
|
0x00, 0x00, 0x1f, 0x10, 0x17, 0x14, // Double bottom left corner 0xc8
|
|
|
|
0x00, 0x00, 0xfc, 0x04, 0xf4, 0x14, // Double top left corner 0xc9
|
|
|
|
0x14, 0x14, 0x17, 0x10, 0x17, 0x14, // Double horizontal with double upward spur 0xca
|
|
|
|
0x14, 0x14, 0xf4, 0x04, 0xf4, 0x14, // Double horizontal with double downward spur 0xcb
|
|
|
|
0x00, 0x00, 0xff, 0x00, 0xf7, 0x14, // Double vertical line with double right spur 0xcc
|
|
|
|
0x14, 0x14, 0x14, 0x14, 0x14, 0x14, // Double horizontal line 0xcd
|
|
|
|
0x14, 0x14, 0xf7, 0x00, 0xf7, 0x14, // Double cross 0xce
|
|
|
|
|
2023-02-25 12:42:43 +01:00
|
|
|
0x14, 0x14, 0x14, 0x17, 0x14, 0x14, // Double horizontal line single upward spur 0xcf
|
|
|
|
0x08, 0x08, 0x0f, 0x08, 0x0f, 0x08, // Horiz single line with double upward spur 0xd0
|
|
|
|
0x14, 0x14, 0x14, 0xf4, 0x14, 0x14, // Horiz double line with single downward spur 0xd1
|
|
|
|
0x08, 0x08, 0xf8, 0x08, 0xf8, 0x08, // Horiz single line with double downward spur 0xd2
|
|
|
|
0x00, 0x00, 0x0f, 0x08, 0x0f, 0x08, // Bottom left corner, double vert single horiz 0xd3
|
|
|
|
0x00, 0x00, 0x00, 0x1f, 0x14, 0x14, // Bottom left corner, single vert double horiz 0xd4
|
|
|
|
0x00, 0x00, 0x00, 0xfc, 0x14, 0x14, // Top left corner, single vert double horiz 0xd5
|
|
|
|
0x00, 0x00, 0xf8, 0x08, 0xf8, 0x08, // Top left corner, double vert single horiz 0xd6
|
|
|
|
0x08, 0x08, 0xff, 0x00, 0xff, 0x08, // Cross, double vert single horiz 0xd7
|
|
|
|
0x14, 0x14, 0x14, 0xf7, 0x14, 0x14, // Cross, single vert double horiz 0xd8
|
2023-02-16 17:41:13 +01:00
|
|
|
|
|
|
|
// Extended characters 217-223
|
|
|
|
0x08, 0x08, 0x08, 0x0f, 0x00, 0x00, // Bottom right corner 0xd9
|
|
|
|
0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, // Top left corner 0xda
|
|
|
|
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, // Solid block 0xdb
|
|
|
|
0xf0, 0xf0, 0xf0, 0xf0, 0xf0, 0xf0, // Bottom half block 0xdc
|
|
|
|
0xff, 0xff, 0xff, 0x00, 0x00, 0x00, // Left half block 0xdd
|
|
|
|
0x00, 0x00, 0x00, 0xff, 0xff, 0xff, // Right half block 0xde
|
|
|
|
0x0f, 0x0f, 0x0f, 0x0f, 0x0f, 0x0f, // Top half block 0xdf
|
|
|
|
|
2023-02-25 12:42:43 +01:00
|
|
|
0xf0, 0xf0, 0xf0, 0x00, 0x00, 0x00, // Bottom Left block 0xe0
|
|
|
|
0x00, 0x00, 0x00, 0xf0, 0xf0, 0xf0, // Bottom Right block
|
|
|
|
0x0f, 0x0f, 0x0f, 0x00, 0x00, 0x00, // Top left block
|
|
|
|
0x00, 0x00, 0x00, 0x0f, 0x0f, 0x0f, // Top right block 0xe3
|
2023-02-16 17:41:13 +01:00
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented 0xf0
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, // Not implemented
|
|
|
|
// Extended character 248
|
2023-02-25 12:42:43 +01:00
|
|
|
0x00, 0x06, 0x09, 0x09, 0x06, 0x00 // degree symbol 0xf8
|
2023-02-16 17:41:13 +01:00
|
|
|
#endif
|
2021-07-13 22:15:38 +02:00
|
|
|
};
|
2023-02-16 17:41:13 +01:00
|
|
|
|
|
|
|
const uint8_t SSD1306AsciiWire::m_fontCharCount = sizeof(System6x8) / 6;
|