2020-09-22 20:57:11 +02:00
////////////////////////////////////////////////////////////////////////////////////
2022-01-06 23:03:57 +01:00
// DCC-EX CommandStation-EX Please see https://DCC-EX.com
2020-09-22 20:57:11 +02:00
//
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
// This file is the main sketch for the Command Station.
2022-01-06 23:03:57 +01:00
//
// CONFIGURATION:
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
// Configuration is normally performed by editing a file called config.h.
// This file is NOT shipped with the code so that if you pull a later version
// of the code, your configuration will not be overwritten.
2020-09-22 20:57:11 +02:00
//
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
// If you used the automatic installer program, config.h will have been created automatically.
2022-01-06 23:03:57 +01:00
//
// To obtain a starting copy of config.h please copy the file config.example.h which is
// shipped with the code and may be updated as new features are added.
//
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
// If config.h is not found, config.example.h will be used with all defaults.
2020-09-22 20:57:11 +02:00
////////////////////////////////////////////////////////////////////////////////////
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
# if __has_include ( "config.h")
# include "config.h"
2022-08-03 09:31:03 +02:00
# ifndef MOTOR_SHIELD_TYPE
# error Your config.h must include a MOTOR_SHIELD_TYPE definition. If you see this warning in spite not having a config.h, you have a buggy preprocessor and must copy config.example.h to config.h
# endif
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
# else
2022-01-06 23:03:57 +01:00
# warning config.h not found. Using defaults from config.example.h
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
# include "config.example.h"
# endif
/*
2022-01-07 02:28:35 +01:00
* © 2021 Neil McKechnie
* © 2020 - 2021 Chris Harlow , Harald Barth , David Cutting ,
* Fred Decker , Gregor Baues , Anthony W - Dayton
2023-07-08 08:58:00 +02:00
* © 2023 Nathan Kellenicki
2022-01-07 02:28:35 +01:00
* All rights reserved .
2022-01-06 23:03:57 +01:00
*
2021-04-14 22:46:29 +02:00
* This file is part of CommandStation - EX
Nano every2 (#129)
* Start adding back unowifi stuffz
* Uno Wifi compiling
* Fixes for compile arduino unowifi r2
* FlasString and Timers for Uno Wifi
ALL these changes should be portable back to master
* Remove extra timer that was already added
* Changed to EveryTimerB
* Add everytimerb.h
* Cleanup
* Linear address <a> cmd
* Allow lower case keywords
* Add the F define to be on safe side if it is not present in the library core code
* Clean simple Timer interface
Removes overkill files, puts all timer in a single small file. (DCCTimer)
* Timer port
* Timer working
And slow wave command removed
* Correcting non-portables merged from master
* Wave-state machine ( part 11)
* Microtuning waveform
Significant reduction in code paths and call overheads
* Current check cleanup
* Fix no-loco id
Has to handle -1 correctly
* fix wrong format letter
* redo flow through wifisetup again
* version++
* bugfixes wifi setup
* Retry harder for AP mode
* Remove unued if
* DIO2 replacement
Currently for writing signal pins during waveform.
* Drop analogReadFast (see DCCTimer)
AnalogRead speed set in DCCTimer for ease of porting.
Code tidy and diagnostics in MotorDriver
* UNTESTED fast power,brake,fault pins
* Distunguish between in/out of FASTPIN
* minor performance tweaks
* Config comments and example use
* Config/example loading
* IP/PORT on LCD
* Ethernet simulated mac
Plus fixed listening port
* Github SHA
* Committing a SHA
* Fix for nano compile
* Comments and a reliability fix.
* UnoRev2 protection
* PWM pin implementation
* fix wifi setup issue
* Reinstate IP_PORT
* Wifi channel and code cleaninga
* Reduce duplicated F() macros
Compiler isn't as clever as one might expect
* Committing a SHA
* Update config.example.h
Add comment to wifi channel section
* Committing a SHA
* Handle shields with common fault pins (Pololu)
* Committing a SHA
* remove warning
* Committing a SHA
* only do the sha generation on master
* yaml syntax
* Fast SSD1306 OLED driver
Incorporate code from SSD1306Ascii library to speed up OLED screen updates, reduce memory requirements and eliminate some library dependences.
* Fix auto-configure from cold boot.
Add call to Wire.begin().
* Update comment for OLED_DRIVER define.
* Update MotorDrivers.h
Add a motor board definition for using the IBT_2 board for a high current to the main track and keep the Arduino Motor Shield for operating the programming track.
* Committing a SHA
* Fix missing F in motor drivers
* JOIN relay pin
* Swap Join Relay high/low
* Hide WIFI_CONNECT_TIMEOUT
This is not what the config suggests it is... The timeout is in the ES and defaults to 15 seconds. Abandoning it early leads to confused setup.
* Enhance OLED/LCD speed
Write one character or position command per loop entry so as not to hold up the loop. Add support for SH1106 OLED as 132x64 size option.
* Enhance OLED/LCD speed
* Delete comment about OLED on UNO.
* Trim unwanted code
* Handle display types correctly
* Update comments
* Speed up OLED writes
Add new flushDisplay() to end any in-progress I2C transaction. Previously, an redundant command was sent that ended the in-progress transaction but also sent another complete, but unnecessary, transaction.
* Comments and copyright update
* Reduce RAM and flash requirement a few more bytes.
* Move statics into LCDDisplay class, and reduce RAM.
Some state variables were static in LCDDisplay.write(). Moved to class members. Also, types of data items like row, column & character position changed to int8_t to save a few bytes of RAM.
* Type lcdCols and lcdRows to unsigned.
Since lcdCols is normally 128, it needs to be uint8_t, not int8_t.
* remove timeout from user config
* faultpin is common only if it exists ; make code prettier
* Rationalisation of SSD1306 driver
Merge SSD1306AsciiWire.cpp into SSD1306Ascii.cpp and rename SSD1306AsciiWire.h as SSD1306Ascii.h.
Merge allFonts.h into System5x7.h and rename as SSD1306font.h.
Move all SSD1306 files into root folder to facilitate compilation in Arduino IDE.
* Fix some font attributes as const.
* Remove unused initialisation sequences for tiny oled screens
* Add m_ to variables
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Revert "Bump up I2C speed"
This reverts commit 1c1168f43314d3a6855738fbc406d5654e801831.
* Bump up I2C speed
Speed was 100kHz (default). Max for OLEDis 400kHz.
* Drop duplicate DIAG
* ignore mySetup.h files
* Restore uno to default_envs
Restore uno (previously commented out) to default_envs.
* Update objdump.bat
Allows other editors as Notepad is very slow on large files
* Prog Track overload during cv read
* Faster LCD Driver
Extract LCD driver from library;
Trim unused functionality;
Reduce I2C communications to minimum;
Speed up I2C clock to 400kHz.
* Update config.example.h
Add IBT_2_WITH_ARDUINO to example config
* Update config.example.h
* Screen enhancements (#126)
* Add I2CManager to coordinate I2C shared parameters.
* Add use of I2CManager, and experimental scrolling strategies.
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
* Scrolling updates
New scrolling capability by defining SCROLLMODE in Config.h to 0 (original), 1 (by page) or 2 (by line). If not defined, defaults to 0.
Reformat.
* Add I2CManager calls. Remove unnecessary delays.
* Add I2CManager calls, remove unnecessary I2C delays.
* SSD1306: Move methods from .h to .cpp and reformat.
* Fix compiler warning in LiquidCrystal_I2C
* Allow forcing of I2C clock speed.
New method forceClock allows the I2C speed to be overridden. For example, if the I2C bus is long then the speed can be forced lower. It can also be forced higher to gain performance if devices are capable.
* Make Config.h conditionally included.
Allow for non-existence of Config.h.
* Correct scrolling and allow longer messages
Correct the handling of scrolling in scrollmode 1 to avoid a blank page being displayed. Also, allow MAX_MSG_SIZE to be optionally configured to override maximum message length on screens.
* compiler warning on uno
Co-authored-by: dexslab <dex35803@gmail.com>
Co-authored-by: Asbelos <asbelos@btinternet.com>
Co-authored-by: Harald Barth <haba@kth.se>
Co-authored-by: Neil McKechnie <neilmck999@gmail.com>
Co-authored-by: Neil McKechnie <75813993+Neil-McK@users.noreply.github.com>
2021-03-07 21:58:35 +01:00
*
* This is free software : you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation , either version 3 of the License , or
* ( at your option ) any later version .
*
* It is distributed in the hope that it will be useful ,
* but WITHOUT ANY WARRANTY ; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
* GNU General Public License for more details .
*
* You should have received a copy of the GNU General Public License
* along with CommandStation . If not , see < https : //www.gnu.org/licenses/>.
*/
2020-09-26 09:49:51 +02:00
# include "DCCEX.h"
2023-02-16 17:41:13 +01:00
# include "Display_Implementation.h"
2022-07-06 18:05:34 +02:00
# ifdef CPU_TYPE_ERROR
# error CANNOT COMPILE - DCC++ EX ONLY WORKS WITH THE ARCHITECTURES LISTED IN defines.h
# endif
2021-12-05 13:24:46 +01:00
# ifdef WIFI_WARNING
# warning You have defined that you want WiFi but your hardware has not enough memory to do that, so WiFi DISABLED
2022-01-06 23:03:57 +01:00
# endif
2021-12-05 13:24:46 +01:00
# ifdef ETHERNET_WARNING
# warning You have defined that you want Ethernet but your hardware has not enough memory to do that, so Ethernet DISABLED
2022-01-06 23:03:57 +01:00
# endif
2021-12-15 21:08:24 +01:00
# ifdef EXRAIL_WARNING
# warning You have myAutomation.h but your hardware has not enough memory to do that, so EX-RAIL DISABLED
# endif
2020-09-12 00:27:46 +02:00
2020-09-22 20:57:11 +02:00
void setup ( )
{
2020-09-12 00:27:46 +02:00
// The main sketch has responsibilities during setup()
2020-09-22 20:57:11 +02:00
// Responsibility 1: Start the usb connection for diagnostics
2020-09-12 00:27:46 +02:00
// This is normally Serial but uses SerialUSB on a SAMD processor
2021-12-05 13:08:59 +01:00
SerialManager : : init ( ) ;
2021-05-16 08:04:43 +02:00
2021-04-14 22:46:29 +02:00
DIAG ( F ( " License GPLv3 fsf.org (c) dcc-ex.com " ) ) ;
2023-04-06 00:19:43 +02:00
// Initialise HAL layer before reading EEprom or setting up MotorDrivers
IODevice : : begin ( ) ;
2023-06-22 23:30:28 +02:00
// As the setup of a motor shield may require a read of the current sense input from the ADC,
// let's make sure to initialise the ADCee class!
ADCee : : begin ( ) ;
// Set up MotorDrivers early to initialize all pins
2023-06-22 22:57:59 +02:00
TrackManager : : Setup ( MOTOR_SHIELD_TYPE ) ;
2023-04-06 00:19:43 +02:00
2023-02-16 17:41:13 +01:00
DISPLAY_START (
// This block is still executed for DIAGS if display not in use
LCD ( 0 , F ( " DCC-EX v%S " ) , F ( VERSION ) ) ;
2022-01-06 23:03:57 +01:00
LCD ( 1 , F ( " Lic GPLv3 " ) ) ;
2023-02-16 17:41:13 +01:00
) ;
2020-09-19 01:40:18 +02:00
2021-05-16 08:04:43 +02:00
// Responsibility 2: Start all the communications before the DCC engine
// Start the WiFi interface on a MEGA, Uno cannot currently handle WiFi
// Start Ethernet if it exists
2022-07-31 08:49:12 +02:00
# ifndef ARDUINO_ARCH_ESP32
2020-10-12 20:32:47 +02:00
# if WIFI_ON
2023-06-29 07:29:53 +02:00
WifiInterface : : setup ( WIFI_SERIAL_LINK_SPEED , F ( WIFI_SSID ) , F ( WIFI_PASSWORD ) , F ( WIFI_HOSTNAME ) , IP_PORT , WIFI_CHANNEL , WIFI_FORCE_AP ) ;
2020-09-25 22:49:53 +02:00
# endif // WIFI_ON
2022-07-31 08:49:12 +02:00
# else
// ESP32 needs wifi on always
2023-06-29 07:29:53 +02:00
WifiESP : : setup ( WIFI_SSID , WIFI_PASSWORD , WIFI_HOSTNAME , IP_PORT , WIFI_CHANNEL , WIFI_FORCE_AP ) ;
2022-07-31 08:49:12 +02:00
# endif // ARDUINO_ARCH_ESP32
2020-09-12 00:27:46 +02:00
2020-10-30 14:00:02 +01:00
# if ETHERNET_ON
2023-03-10 11:53:40 +01:00
# ifdef ETHERNET_CS
Ethernet . init ( ETHERNET_CS ) ;
# endif // ETHERNET_CS
2020-10-30 14:00:02 +01:00
EthernetInterface : : setup ( ) ;
# endif // ETHERNET_ON
2023-04-06 00:19:43 +02:00
2021-05-16 08:04:43 +02:00
// Responsibility 3: Start the DCC engine.
2023-06-22 22:57:59 +02:00
DCC : : begin ( ) ;
2022-01-06 23:03:57 +01:00
2022-01-30 18:31:26 +01:00
// Start RMFT aka EX-RAIL (ignored if no automnation)
2021-08-03 23:12:25 +02:00
RMFT : : begin ( ) ;
2021-05-16 08:04:43 +02:00
2022-01-06 23:03:57 +01:00
// Invoke any DCC++EX commands in the form "SETUP("xxxx");"" found in optional file mySetup.h.
2021-11-12 01:05:16 +01:00
// This can be used to create turnouts, outputs, sensors etc. through the normal text commands.
2021-01-07 21:58:23 +01:00
# if __has_include ( "mySetup.h")
2022-04-05 03:24:29 +02:00
# define SETUP(cmd) DCCEXParser::parse(F(cmd))
# include "mySetup.h"
# undef SETUP
2022-01-06 23:03:57 +01:00
# endif
2021-01-07 21:58:23 +01:00
2021-03-23 15:37:05 +01:00
# if defined(LCN_SERIAL)
2022-01-06 23:03:57 +01:00
LCN_SERIAL . begin ( 115200 ) ;
LCN : : init ( LCN_SERIAL ) ;
2021-03-23 15:37:05 +01:00
# endif
2022-04-05 03:24:29 +02:00
LCD ( 3 , F ( " Ready " ) ) ;
2021-12-16 13:11:38 +01:00
CommandDistributor : : broadcastPower ( ) ;
2020-09-12 00:27:46 +02:00
}
2020-09-22 20:57:11 +02:00
void loop ( )
{
2020-09-12 00:27:46 +02:00
// The main sketch has responsibilities during loop()
2020-09-22 20:57:11 +02:00
2020-09-12 00:27:46 +02:00
// Responsibility 1: Handle DCC background processes
// (loco reminders and power checks)
2020-09-22 20:57:11 +02:00
DCC : : loop ( ) ;
2020-09-12 00:27:46 +02:00
// Responsibility 2: handle any incoming commands on USB connection
2021-12-05 13:08:59 +01:00
SerialManager : : loop ( ) ;
2020-09-12 00:27:46 +02:00
2022-01-06 23:03:57 +01:00
// Responsibility 3: Optionally handle any incoming WiFi traffic
2022-07-31 08:49:12 +02:00
# ifndef ARDUINO_ARCH_ESP32
2020-10-04 17:29:48 +02:00
# if WIFI_ON
2020-09-12 00:27:46 +02:00
WifiInterface : : loop ( ) ;
2022-07-31 08:49:12 +02:00
# endif //WIFI_ON
2022-08-16 12:25:49 +02:00
# else //ARDUINO_ARCH_ESP32
# ifndef WIFI_TASK_ON_CORE0
WifiESP : : loop ( ) ;
# endif
2022-07-31 08:49:12 +02:00
# endif //ARDUINO_ARCH_ESP32
2020-10-30 14:00:02 +01:00
# if ETHERNET_ON
EthernetInterface : : loop ( ) ;
# endif
2020-10-12 20:32:47 +02:00
2021-08-03 23:12:25 +02:00
RMFT : : loop ( ) ; // ignored if no automation
2021-01-05 19:05:17 +01:00
2022-01-06 23:03:57 +01:00
# if defined(LCN_SERIAL)
LCN : : loop ( ) ;
2021-03-23 15:37:05 +01:00
# endif
2023-02-16 17:41:13 +01:00
// Display refresh
DisplayInterface : : loop ( ) ;
2021-08-03 23:12:25 +02:00
// Handle/update IO devices.
IODevice : : loop ( ) ;
2022-01-06 23:03:57 +01:00
2021-12-05 13:08:59 +01:00
Sensor : : checkAll ( ) ; // Update and print changes
2021-03-10 00:41:33 +01:00
// Report any decrease in memory (will automatically trigger on first call)
2022-01-06 23:03:57 +01:00
static int ramLowWatermark = __INT_MAX__ ; // replaced on first loop
2020-09-26 09:42:24 +02:00
2022-03-01 13:52:25 +01:00
int freeNow = DCCTimer : : getMinimumFreeMemory ( ) ;
2022-01-06 23:03:57 +01:00
if ( freeNow < ramLowWatermark ) {
2020-09-22 20:57:11 +02:00
ramLowWatermark = freeNow ;
2021-08-23 12:58:48 +02:00
LCD ( 3 , F ( " Free RAM=%5db " ) , ramLowWatermark ) ;
2020-09-22 20:57:11 +02:00
}
2020-09-12 00:27:46 +02:00
}