Check bad AT firmware version

My 1st commit, be gentle

DCCACK.cpp

@@ -351,7 +351,7 @@ void DCCACK::callback(int value) {
 
     switch (callbackState) {
       case AFTER_READ:
-         if (ackManagerRejoin && autoPowerOff) {
+         if (ackManagerRejoin && !autoPowerOff) {
                 progDriver->setPower(POWERMODE::OFF);
                 callbackStart=millis();
                 callbackState=WAITING_30;

DCCEXParser.cpp

@@ -25,6 +25,79 @@
  *  You should have received a copy of the GNU General Public License
  *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
  */
+
+/*
+List of single character OPCODEs in use for reference.
+
+When determining a new OPCODE for a new feature, refer to this list as the source of truth.
+
+Once a new OPCODE is decided upon, update this list.
+
+  Character, Usage
+  /, |EX-R| interactive commands
+  -, Remove from reminder table
+  =, |TM| configuration
+  !, Emergency stop
+  @, Reserved for future use - LCD messages to JMRI
+  #, Request number of supported cabs/locos; heartbeat
+  +, WiFi AT commands
+  ?, Reserved for future use
+  0, Track power off
+  1, Track power on
+  a, DCC accessory control
+  A,
+  b, Write CV bit on main
+  B, Write CV bit
+  c, Request current command
+  C,
+  d,
+  D, Diagnostic commands
+  e, Erase EEPROM
+  E, Store configuration in EEPROM
+  f, Loco decoder function control (deprecated)
+  F, Loco decoder function control
+  g,
+  G,
+  h,
+  H, Turnout state broadcast
+  i, Reserved for future use - Turntable object broadcast
+  I, Reserved for future use - Turntable object command and control
+  j, Throttle responses
+  J, Throttle queries
+  k, Reserved for future use - Potentially Railcom
+  K, Reserved for future use - Potentially Railcom
+  l, Loco speedbyte/function map broadcast
+  L,
+  m,
+  M, Write DCC packet
+  n,
+  N,
+  o,
+  O, Output broadcast
+  p, Broadcast power state
+  P, Write DCC packet
+  q, Sensor deactivated
+  Q, Sensor activated
+  r, Broadcast address read on programming track
+  R, Read CVs
+  s, Display status
+  S, Sensor configuration
+  t, Cab/loco update command
+  T, Turnout configuration/control
+  u, Reserved for user commands
+  U, Reserved for user commands
+  v,
+  V, Verify CVs
+  w, Write CV on main
+  W, Write CV
+  x,
+  X, Invalid command
+  y,
+  Y, Output broadcast
+  z,
+  Z, Output configuration/control
+*/
+
 #include "StringFormatter.h"
 #include "DCCEXParser.h"
 #include "DCC.h"
@@ -219,6 +292,9 @@ void DCCEXParser::parse(Print *stream,  byte *com,  RingStream *ringStream) {
 
 void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
 {
+#ifdef DISABLE_PROG
+    (void)ringStream;
+#endif
 #ifndef DISABLE_EEPROM
     (void)EEPROM; // tell compiler not to warn this is unused
 #endif

DCCTimerSTM32.cpp

@@ -35,7 +35,7 @@
 #endif
 #include "DIAG.h"
 
-#if defined(ARDUINO_NUCLEO_F411RE)
+#if defined(ARDUINO_NUCLEO_F401RE) || defined(ARDUINO_NUCLEO_F411RE)
 // Nucleo-64 boards don't have additional serial ports defined by default
 HardwareSerial Serial1(PB7, PA15);  // Rx=PB7, Tx=PA15 -- CN7 pins 17 and 21 - F411RE
 // Serial2 is defined to use USART2 by default, but is in fact used as the diag console
@@ -52,7 +52,7 @@ HardwareSerial Serial6(PA12, PA11);  // Rx=PA12, Tx=PA11 -- CN10 pins 12 and 14
 HardwareSerial Serial3(PC11, PC10);  // Rx=PC11, Tx=PC10 -- USART3 - F446RE
 HardwareSerial Serial5(PD2, PC12);  // Rx=PC7, Tx=PC6 -- UART5 - F446RE
 // On the F446RE, Serial4 and Serial6 also use pins we can't readily map while using the Arduino pins
-#elif defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
+#elif defined(ARDUINO_NUCLEO_F413ZH) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)|| defined(ARDUINO_NUCLEO_F412ZG) 
 // Nucleo-144 boards don't have Serial1 defined by default
 HardwareSerial Serial6(PG9, PG14);  // Rx=PG9, Tx=PG14 -- USART6
 // Serial3 is defined to use USART3 by default, but is in fact used as the diag console

GITHUB_SHA.h

@@ -1 +1 @@
-#define GITHUB_SHA "devel-202307250927Z"
+#define GITHUB_SHA "3bddf4d"

IO_PCA9555.h

@@ -0,0 +1,112 @@
+/*
+ *  © 2021, Neil McKechnie. All rights reserved.
+ *  
+ *  This file is part of DCC++EX API
+ *
+ *  This is free software: you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation, either version 3 of the License, or
+ *  (at your option) any later version.
+ *
+ *  It is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
+ */
+
+#ifndef io_pca9555_h
+#define io_pca9555_h
+
+#include "IO_GPIOBase.h"
+#include "FSH.h"
+
+/////////////////////////////////////////////////////////////////////////////////////////////////////
+/*
+ * IODevice subclass for PCA9555 16-bit I/O expander (NXP & Texas Instruments).
+ */
+ 
+class PCA9555 : public GPIOBase<uint16_t> {
+public:
+  static void create(VPIN vpin, int nPins, uint8_t I2CAddress, int interruptPin=-1) {
+    new PCA9555(vpin, min(nPins,16), I2CAddress, interruptPin);
+  }
+  
+  // Constructor
+  PCA9555(VPIN vpin, int nPins, uint8_t I2CAddress, int interruptPin=-1) 
+    : GPIOBase<uint16_t>((FSH *)F("PCA9555"), vpin, nPins, I2CAddress, interruptPin) 
+  {
+    requestBlock.setRequestParams(_I2CAddress, inputBuffer, sizeof(inputBuffer),
+      outputBuffer, sizeof(outputBuffer));
+    outputBuffer[0] = REG_INPUT_P0;
+  }
+
+private:
+  void _writeGpioPort() override {
+    I2CManager.write(_I2CAddress, 3, REG_OUTPUT_P0, _portOutputState, _portOutputState>>8);
+  }
+  void _writePullups() override {
+    // Do nothing, pull-ups are always in place for input ports
+    // This function is here for HAL GPIOBase API compatibilitiy
+      
+  }
+  void _writePortModes() override {
+    // Write 0 to REG_CONF_P0 & REG_CONF_P1 for in-use pins that are outputs, 1 for others.
+    // PCA9555 & TCA9555, Interrupt is always enabled for raising and falling edge
+    uint16_t temp = ~(_portMode & _portInUse);
+    I2CManager.write(_I2CAddress, 3, REG_CONF_P0, temp, temp>>8);    
+  }
+  void _readGpioPort(bool immediate) override {
+    if (immediate) {
+      uint8_t buffer[2];
+      I2CManager.read(_I2CAddress, buffer, 2, 1, REG_INPUT_P0);
+      _portInputState = ((uint16_t)buffer[1]<<8) | buffer[0];
+      /* PCA9555 Int bug fix, from PCA9555 datasheet: "must change command byte to something besides 00h 
+       * after a Read operation to the PCA9555 device or before reading from 
+       * another device"
+       * Recommended solution, read from REG_OUTPUT_P0, then do nothing with the received data
+       * Issue not seen during testing, uncomment if needed 
+       */
+      //I2CManager.read(_I2CAddress, buffer, 2, 1, REG_OUTPUT_P0);
+    } else {
+      // Queue new request
+      requestBlock.wait(); // Wait for preceding operation to complete
+      // Issue new request to read GPIO register
+      I2CManager.queueRequest(&requestBlock);
+    }
+  }
+  // This function is invoked when an I/O operation on the requestBlock completes.
+  void _processCompletion(uint8_t status) override {
+    if (status == I2C_STATUS_OK) 
+      _portInputState = ((uint16_t)inputBuffer[1]<<8) | inputBuffer[0];
+    else  
+      _portInputState = 0xffff;
+  }
+
+  void _setupDevice() override {
+    // HAL API calls
+    _writePortModes();
+    _writePullups();
+    _writeGpioPort();
+  }
+ 
+  uint8_t inputBuffer[2];
+  uint8_t outputBuffer[1];
+ 
+
+  enum {
+    REG_INPUT_P0 = 0x00,
+    REG_INPUT_P1 = 0x01,
+    REG_OUTPUT_P0 = 0x02,
+    REG_OUTPUT_P1 = 0x03,
+    REG_POL_INV_P0 = 0x04,
+    REG_POL_INV_P1 = 0x05,
+    REG_CONF_P0 = 0x06,
+    REG_CONF_P1 = 0x07,    
+  };
+
+};
+
+#endif

MotorDriver.cpp

@@ -291,14 +291,39 @@ uint16_t taurustones[28] = { 165, 175, 196, 220,
 void MotorDriver::setDCSignal(byte speedcode) {
   if (brakePin == UNUSED_PIN)
     return;
+  switch(brakePin) {
 #if defined(ARDUINO_AVR_UNO)
-  TCCR2B = (TCCR2B & B11111000) | B00000110; // set divisor on timer 2 to result in (approx) 122.55Hz
+    // Not worth doin something here as:
+    // If we are on pin 9 or 10 we are on Timer1 and we can not touch Timer1 as that is our DCC source.
+    // If we are on pin 5 or 6 we are on Timer 0 ad we can not touch Timer0 as that is millis() etc.
+    // We are most likely not on pin 3 or 11 as no known motor shield has that as brake.
 #endif
 #if defined(ARDUINO_AVR_MEGA) || defined(ARDUINO_AVR_MEGA2560)
-  TCCR2B = (TCCR2B & B11111000) | B00000110; // set divisor on timer 2 to result in (approx) 122.55Hz
-  TCCR4B = (TCCR4B & B11111000) | B00000100; // same for timer 4 but maxcount and thus divisor differs
-  TCCR5B = (TCCR5B & B11111000) | B00000100; // same for timer 5 which is like timer 4
+  case 9:
+  case 10:
+    // Timer2 (is differnet)
+    TCCR2A = (TCCR2A & B11111100) | B00000001; // set WGM1=0 and WGM0=1 phase correct PWM
+    TCCR2B = (TCCR2B & B11110000) | B00000110; // set WGM2=0 ; set divisor on timer 2 to 1/256 for 122.55Hz
+    //DIAG(F("2 A=%x B=%x"), TCCR2A, TCCR2B);
+    break;
+  case 6:
+  case 7:
+  case 8:
+    // Timer4
+    TCCR4A = (TCCR4A & B11111100) | B00000001; // set WGM0=1 and WGM1=0 for normal PWM 8-bit
+    TCCR4B = (TCCR4B & B11100000) | B00000100; // set WGM2=0 and WGM3=0 for normal PWM 8 bit and div 1/256 for 122.55Hz
+    break;
+  case 46:
+  case 45:
+  case 44:
+    // Timer5
+    TCCR5A = (TCCR5A & B11111100) | B00000001; // set WGM0=1 and WGM1=0 for normal PWM 8-bit
+    TCCR5B = (TCCR5B & B11100000) | B00000100; // set WGM2=0 and WGM3=0 for normal PWM 8 bit and div 1/256 for 122.55Hz
+    break;
 #endif
+  default:
+    break;
+  }
   // spedcoode is a dcc speed & direction
   byte tSpeed=speedcode & 0x7F; // DCC Speed with 0,1 stop and speed steps 2 to 127
   byte tDir=speedcode & 0x80;
@@ -368,14 +393,39 @@ void MotorDriver::throttleInrush(bool on) {
   }
 #else
   if(on){
+    switch(brakePin) {
 #if defined(ARDUINO_AVR_UNO)
-  TCCR2B = (TCCR2B & B11111000) | B00000001; // div 1 is max
+      // Not worth doin something here as:
+      // If we are on pin 9 or 10 we are on Timer1 and we can not touch Timer1 as that is our DCC source.
+      // If we are on pin 5 or 6 we are on Timer 0 ad we can not touch Timer0 as that is millis() etc.
+      // We are most likely not on pin 3 or 11 as no known motor shield has that as brake.
 #endif
 #if defined(ARDUINO_AVR_MEGA) || defined(ARDUINO_AVR_MEGA2560)
-  TCCR2B = (TCCR2B & B11111000) | B00000001; // div 1 is max
-  TCCR4B = (TCCR4B & B11111000) | B00000001; // div 1 is max
-  TCCR5B = (TCCR5B & B11111000) | B00000001; // div 1 is max
+    case 9:
+    case 10:
+      // Timer2 (is different)
+      TCCR2A = (TCCR2A & B11111100) | B00000011; // set WGM0=1 and WGM1=1 for fast PWM
+      TCCR2B = (TCCR2B & B11110000) | B00000001; // set WGM2=0 and prescaler div=1 (max)
+      DIAG(F("2 A=%x B=%x"), TCCR2A, TCCR2B);
+      break;
+    case 6:
+    case 7:
+    case 8:
+      // Timer4
+      TCCR4A = (TCCR4A & B11111100) | B00000001; // set WGM0=1 and WGM1=0 for fast PWM 8-bit
+      TCCR4B = (TCCR4B & B11100000) | B00001001; // set WGM2=1 and WGM3=0 for fast PWM 8 bit and div=1 (max)
+      break;
+    case 46:
+    case 45:
+    case 44:
+      // Timer5
+      TCCR5A = (TCCR5A & B11111100) | B00000001; // set WGM0=1 and WGM1=0 for fast PWM 8-bit
+      TCCR5B = (TCCR5B & B11100000) | B00001001; // set WGM2=1 and WGM3=0 for fast PWM 8 bit and div=1 (max)
+      break;
 #endif
+    default:
+      break;
+    }
   }
   analogWrite(brakePin,duty);
 #endif

MotorDriver.h

@@ -28,7 +28,7 @@
 #include "DCCTimer.h"
 
 // use powers of two so we can do logical and/or on the track modes in if clauses.
-enum TRACK_MODE : byte {TRACK_MODE_OFF = 1, TRACK_MODE_MAIN = 2, TRACK_MODE_PROG = 4,
+enum TRACK_MODE : byte {TRACK_MODE_NONE = 1, TRACK_MODE_MAIN = 2, TRACK_MODE_PROG = 4,
                         TRACK_MODE_DC = 8, TRACK_MODE_DCX = 16, TRACK_MODE_EXT = 32};
 
 #define setHIGH(fastpin)  *fastpin.inout |= fastpin.maskHIGH
@@ -290,7 +290,7 @@ class MotorDriver {
     static const int TRIP_CURRENT_PROG=250;
     unsigned long power_sample_overload_wait = POWER_SAMPLE_OVERLOAD_WAIT;
     unsigned int power_good_counter = 0;
-    TRACK_MODE trackMode = TRACK_MODE_OFF; // we assume off at startup
+    TRACK_MODE trackMode = TRACK_MODE_NONE; // we assume track not assigned at startup
 
 };
 #endif

TrackManager.cpp

@@ -38,6 +38,7 @@ const int16_t HASH_KEYWORD_PROG = -29718;
 #endif
 const int16_t HASH_KEYWORD_MAIN = 11339;
 const int16_t HASH_KEYWORD_OFF = 22479;  
+const int16_t HASH_KEYWORD_NONE = -26550;
 const int16_t HASH_KEYWORD_DC = 2183;  
 const int16_t HASH_KEYWORD_DCX = 6463; // DC reversed polarity 
 const int16_t HASH_KEYWORD_EXT = 8201; // External DCC signal
@@ -52,7 +53,7 @@ bool TrackManager::progTrackSyncMain=false;
 bool TrackManager::progTrackBoosted=false; 
 int16_t TrackManager::joinRelay=UNUSED_PIN;
 #ifdef ARDUINO_ARCH_ESP32
-byte TrackManager::tempProgTrack=MAX_TRACKS+1;
+byte TrackManager::tempProgTrack=MAX_TRACKS+1; // MAX_TRACKS+1 is the unused flag
 #endif
 
 #ifdef ANALOG_READ_INTERRUPT
@@ -140,7 +141,7 @@ void TrackManager::addTrack(byte t, MotorDriver* driver) {
      track[t]=driver;
      if (driver) {
          track[t]->setPower(POWERMODE::OFF);
-         track[t]->setMode(TRACK_MODE_OFF);
+         track[t]->setMode(TRACK_MODE_NONE);
 	 track[t]->setTrackLetter('A'+t);
          lastTrack=t;
      } 
@@ -181,7 +182,7 @@ void TrackManager::setPROGSignal( bool on) {
 // with interrupts turned off around the critical section
 void TrackManager::setDCSignal(int16_t cab, byte speedbyte) {
   FOR_EACH_TRACK(t) {
-    if (trackDCAddr[t]!=cab) continue;
+    if (trackDCAddr[t]!=cab && cab != 0) continue;
     if (track[t]->getMode()==TRACK_MODE_DC) track[t]->setDCSignal(speedbyte);
     else if (track[t]->getMode()==TRACK_MODE_DCX) track[t]->setDCSignal(speedbyte ^ 128);
   }
@@ -192,11 +193,16 @@ bool TrackManager::setTrackMode(byte trackToSet, TRACK_MODE mode, int16_t dcAddr
 
     //DIAG(F("Track=%c Mode=%d"),trackToSet+'A', mode);
     // DC tracks require a motorDriver that can set brake!
-    if ((mode==TRACK_MODE_DC || mode==TRACK_MODE_DCX)
-         && !track[trackToSet]->brakeCanPWM()) {
-             DIAG(F("Brake pin can't PWM: No DC"));
-             return false; 
-         }
+    if (mode==TRACK_MODE_DC || mode==TRACK_MODE_DCX) {
+#if defined(ARDUINO_AVR_UNO)
+      DIAG(F("Uno has no PWM timers available for DC"));
+      return false;
+#endif
+      if (!track[trackToSet]->brakeCanPWM()) {
+	DIAG(F("Brake pin can't PWM: No DC"));
+	return false;
+      }
+    }
 
 #ifdef ARDUINO_ARCH_ESP32
     // remove pin from MUX matrix and turn it off
@@ -219,7 +225,7 @@ bool TrackManager::setTrackMode(byte trackToSet, TRACK_MODE mode, int16_t dcAddr
       FOR_EACH_TRACK(t)
 	if (track[t]->getMode()==TRACK_MODE_PROG && t != trackToSet) {
 	  track[t]->setPower(POWERMODE::OFF);
-	  track[t]->setMode(TRACK_MODE_OFF);
+	  track[t]->setMode(TRACK_MODE_NONE);
 	  track[t]->makeProgTrack(false);     // revoke prog track special handling
     streamTrackState(NULL,t);
 	}
@@ -327,8 +333,8 @@ bool TrackManager::parseJ(Print *stream, int16_t params, int16_t p[])
         return setTrackMode(p[0],TRACK_MODE_PROG);
 #endif
     
-    if (params==2  && p[1]==HASH_KEYWORD_OFF) // <= id OFF>
-        return setTrackMode(p[0],TRACK_MODE_OFF);
+    if (params==2  && (p[1]==HASH_KEYWORD_OFF || p[1]==HASH_KEYWORD_NONE)) // <= id OFF> <= id NONE>
+        return setTrackMode(p[0],TRACK_MODE_NONE);
 
     if (params==2  && p[1]==HASH_KEYWORD_EXT) // <= id EXT>
         return setTrackMode(p[0],TRACK_MODE_EXT);
@@ -355,8 +361,8 @@ void TrackManager::streamTrackState(Print* stream, byte t) {
       format=F("<= %c PROG>\n");
       break;
 #endif
-  case TRACK_MODE_OFF:
-      format=F("<= %c OFF>\n");
+  case TRACK_MODE_NONE:
+      format=F("<= %c NONE>\n");
       break;
   case TRACK_MODE_EXT:
       format=F("<= %c EXT>\n");
@@ -438,7 +444,7 @@ void TrackManager::setPower2(bool setProg,POWERMODE mode) {
 	        driver->setBrake(false);
 		driver->setPower(mode);
 	        break;
-            case TRACK_MODE_OFF:
+            case TRACK_MODE_NONE:
                 break;
         }
     }
@@ -499,7 +505,12 @@ void TrackManager::setJoin(bool joined) {
     }
   } else {
     if (tempProgTrack != MAX_TRACKS+1) {
+      // as setTrackMode with TRACK_MODE_PROG defaults to
+      // power off, we will take the current power state
+      // of our track and then preserve that state.
+      POWERMODE tPTmode = track[tempProgTrack]->getPower(); //get current power status of this track
       setTrackMode(tempProgTrack, TRACK_MODE_PROG);
+      track[tempProgTrack]->setPower(tPTmode);              //set track status as it was before
       tempProgTrack = MAX_TRACKS+1;
     }
   }

WifiInterface.cpp

@@ -60,7 +60,7 @@ Stream * WifiInterface::wifiStream;
 #if defined(ARDUINO_ARCH_STM32)
 // Handle serial ports availability on STM32 for variants!
 // #undef NUM_SERIAL
-#if defined(ARDUINO_NUCLEO_F411RE)
+#if defined(ARDUINO_NUCLEO_F401RE) || defined(ARDUINO_NUCLEO_F411RE)
 #define NUM_SERIAL 3
 #define SERIAL1 Serial1
 #define SERIAL3 Serial6
@@ -68,9 +68,11 @@ Stream * WifiInterface::wifiStream;
 #define NUM_SERIAL 3
 #define SERIAL1 Serial3
 #define SERIAL3 Serial5
-#elif defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
+#elif defined(ARDUINO_NUCLEO_F413ZH) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE) || defined(ARDUINO_NUCLEO_F412ZG)
 #define NUM_SERIAL 2
 #define SERIAL1 Serial6
+#else
+#warning This variant of Nucleo not yet explicitly supported
 #endif
 #endif
 
@@ -198,7 +200,21 @@ wifiSerialState WifiInterface::setup2(const FSH* SSid, const FSH* password,
 
   // Display the AT version information
   StringFormatter::send(wifiStream, F("AT+GMR\r\n")); 
-  checkForOK(2000, true, false);      // Makes this visible on the console
+  if (checkForOK(2000, F("AT version:"), true, false)) {
+    char version[] = "0.0.0.0";
+    for (int i=0; i<8;i++) {
+      while(!wifiStream->available());
+      version[i]=wifiStream->read();
+      StringFormatter::printEscape(version[i]);
+      if ((version[0] == '0') ||
+	  (version[0] == '2' && version[2] == '0') ||
+	  (version[0] == '2' && version[2] == '2' && version[4] == '0' && version[6] == '0')) {
+	SSid = F("DCCEX_SAYS_BROKEN_FIRMWARE");
+	forceAP = true;
+      }
+    }
+  }
+  checkForOK(2000, true, false);
 
 #ifdef DONT_TOUCH_WIFI_CONF
   DIAG(F("DONT_TOUCH_WIFI_CONF was set: Using existing config"));

myHal.cpp_example.txt

@@ -24,6 +24,7 @@
 //#include "IO_TouchKeypad.h  // Touch keypad with 16 keys
 //#include "IO_EXTurntable.h"   // Turntable-EX turntable controller
 //#include "IO_EXFastClock.h"  // FastClock driver
+//#include "IO_PCA9555.h"     // 16-bit I/O expander (NXP & Texas Instruments).
 
 //==========================================================================
 // The function halSetup() is invoked from CS if it exists within the build.
@@ -51,7 +52,7 @@ void halSetup() {
   // Create a 20x4 LCD display device as display number 2 
   // (line 0 is written by EX-RAIL 'SCREEN(2, 0, "text")').
 
-  // HALDisplay<LiquidCrystal>(2, 0x27, 20, 4);
+  // HALDisplay<LiquidCrystal>::create(2, 0x27, 20, 4);
 
 
   //=======================================================================

version.h

@@ -3,7 +3,17 @@
 
 #include "StringFormatter.h"
 
-#define VERSION "4.2.66"
+#define VERSION "5.0.3"
+// 5.0.3  - Check bad AT firmware version
+// 5.0.2  - Bugfix: ESP32 30ms off time
+// 5.0.1  - Bugfix: execute 30ms off time before rejoin
+// 5.0.0  - Make 4.2.69 the 5.0.0 release
+// 4.2.69 - Bugfix: Make <!> work in DC mode
+// 4.2.68 - Rename track mode OFF to NONE
+// 4.2.67 - AVR: Pin specific timer register seting
+//        - Protect Uno user from choosing DC(X)
+//        - More Nucleo variant defines
+//        - GPIO PCA9555 / TCA9555 support
 // 4.2.66 - Throttle inrush current by applying PWM to brake pin when
 //          fault pin goes active
 // 4.2.65 - new config WIFI_FORCE_AP option