set lastPowerChange we doing the power on retry after overload

fix power change timer micros overflow
STM32: Use mask as loop variable
2025-07-29 02:13:45 +02:00 · 2023-06-19 08:43:50 +02:00 · 2023-06-19 00:33:53 +02:00 · 2023-06-18 19:26:38 +02:00 · 2023-06-18 09:48:15 +02:00 · 2023-06-18 09:01:32 +02:00
32 changed files with 1123 additions and 440 deletions
--- a/CommandDistributor.cpp
+++ b/CommandDistributor.cpp
@@ -2,6 +2,7 @@
 *  © 2022 Harald Barth
 *  © 2020-2021 Chris Harlow
 *  © 2020 Gregor Baues
+ *  © 2022 Colin Murdoch
 *  All rights reserved.
 *
 *  This file is part of CommandStation-EX
@@ -167,7 +168,7 @@ void  CommandDistributor::broadcastClockTime(int16_t time, int8_t rate) {
  // be safe for both types.
  broadcastReply(COMMAND_TYPE, F("<jC %d %d>\n"),time, rate);
 #ifdef CD_HANDLE_RING
-  broadcastReply(WITHROTTLE_TYPE, F("PFT%d<;>%d\n"), time*60, rate);
+  broadcastReply(WITHROTTLE_TYPE, F("PFT%l<;>%d\n"), (int32_t)time*60, rate);
 #endif
 }

@@ -204,6 +205,39 @@ int16_t CommandDistributor::retClockTime() {
 void  CommandDistributor::broadcastLoco(byte slot) {
  DCC::LOCO * sp=&DCC::speedTable[slot];
  broadcastReply(COMMAND_TYPE, F("<l %d %d %d %l>\n"), sp->loco,slot,sp->speedCode,sp->functions);
+#ifdef SABERTOOTH
+  if (Serial2 && sp->loco == SABERTOOTH) {
+    static uint8_t rampingmode = 0;
+    bool direction = (sp->speedCode & 0x80) !=0; // true for forward
+    int32_t speed = sp->speedCode & 0x7f;
+    if (speed == 1) { // emergency stop
+      if (rampingmode != 1) {
+	rampingmode = 1;
+	Serial2.print("R1: 0\r\n");
+	Serial2.print("R2: 0\r\n");
+      }
+      Serial2.print("MD: 0\r\n");
+    } else {
+      if (speed != 0) {
+        // speed is here 2 to 127
+	speed = (speed - 1) * 1625 / 100;
+	speed = speed * (direction ? 1 : -1);
+	// speed is here -2047 to 2047
+      }
+      if (rampingmode != 2) {
+	rampingmode = 2;
+	Serial2.print("R1: 2047\r\n");
+	Serial2.print("R2: 2047\r\n");
+      }
+      Serial2.print("M1: ");
+      Serial2.print(speed);
+      Serial2.print("\r\n");
+      Serial2.print("M2: ");
+      Serial2.print(speed);
+      Serial2.print("\r\n");
+    }
+  }
+#endif
 #ifdef CD_HANDLE_RING
  WiThrottle::markForBroadcast(sp->loco);
 #endif
@@ -227,11 +261,8 @@ void  CommandDistributor::broadcastPower() {
  LCD(2,F("Power %S%S"),state=='1'?F("On"):F("Off"),reason);  
 }

-void CommandDistributor::broadcastText(const FSH * msg) {
-  broadcastReply(COMMAND_TYPE, F("<I %S>\n"),msg);
-#ifdef CD_HANDLE_RING
-  broadcastReply(WITHROTTLE_TYPE, F("Hm%S\n"), msg);
-#endif
+void CommandDistributor::broadcastRaw(clientType type, char * msg) {
+  broadcastReply(type, F("%s"),msg);
 }

 void CommandDistributor::broadcastTrackState(const FSH* format,byte trackLetter,int16_t dcAddr) {
--- a/CommandDistributor.h
+++ b/CommandDistributor.h
@@ -2,6 +2,8 @@
 *  © 2022 Harald Barth
 *  © 2020-2021 Chris Harlow
 *  © 2020 Gregor Baues
+ *  © 2022 Colin Murdoch
+ * 
 *  All rights reserved.
 *
 *  This file is part of CommandStation-EX
@@ -33,8 +35,9 @@
 #endif 

 class CommandDistributor {
-private:
+public:
  enum clientType: byte {NONE_TYPE,COMMAND_TYPE,WITHROTTLE_TYPE};
+private:
  static void broadcastToClients(clientType type);
  static StringBuffer * broadcastBufferWriter;
  #ifdef CD_HANDLE_RING
@@ -50,7 +53,7 @@ public :
  static void setClockTime(int16_t time, int8_t rate, byte opt);
  static int16_t retClockTime();
  static void broadcastPower();
-  static void broadcastText(const FSH * msg);
+  static void broadcastRaw(clientType type,char * msg);
  static void broadcastTrackState(const FSH* format,byte trackLetter,int16_t dcAddr);
  template<typename... Targs> static void broadcastReply(clientType type, Targs... msg);
  static void forget(byte clientId);
--- a/DCC.cpp
+++ b/DCC.cpp
@@ -693,7 +693,7 @@ void  DCC::updateLocoReminder(int loco, byte speedCode) {

  if (loco==0) {
     // broadcast stop/estop but dont change direction
-     for (int reg = 0; reg < highestUsedReg; reg++) {
+     for (int reg = 0; reg <= highestUsedReg; reg++) {
       if (speedTable[reg].loco==0) continue;
       byte newspeed=(speedTable[reg].speedCode & 0x80) |  (speedCode & 0x7f);
       if (speedTable[reg].speedCode != newspeed) {
--- a/DCCACK.cpp
+++ b/DCCACK.cpp
@@ -152,7 +152,7 @@ byte DCCACK::getAck() {
      return(0);  // pending set off but not detected means no ACK.   
 }

-
+#ifndef DISABLE_PROG
 void DCCACK::loop() {
  while (ackManagerProg) {
    byte opcode=GETFLASH(ackManagerProg);
@@ -414,7 +414,7 @@ void DCCACK::callback(int value) {
          (ackManagerCallback)( value);
    }
 }
-
+#endif

 void DCCACK::checkAck(byte sentResetsSincePacket) {
    if (!ackPending) return; 
--- a/DCCEXParser.cpp
+++ b/DCCEXParser.cpp
@@ -3,10 +3,11 @@
 *  © 2021 Neil McKechnie
 *  © 2021 Mike S
 *  © 2021 Herb Morton
- *  © 2020-2022 Harald Barth
+ *  © 2020-2023 Harald Barth
 *  © 2020-2021 M Steve Todd
 *  © 2020-2021 Fred Decker
 *  © 2020-2021 Chris Harlow
+ *  © 2022 Colin Murdoch
 *  All rights reserved.
 *  
 *  This file is part of CommandStation-EX
@@ -46,16 +47,14 @@
 #define SENDFLASHLIST(stream,flashList)                 \
    for (int16_t i=0;;i+=sizeof(flashList[0])) {                            \
        int16_t value=GETHIGHFLASHW(flashList,i);       \
-        if (value==0) break;                            \
-        StringFormatter::send(stream,F(" %d"),value);   \
+        if (value==INT16_MAX) break;                            \
+        if (value != 0) StringFormatter::send(stream,F(" %d"),value);	\
    }                                   


 // These keywords are used in the <1> command. The number is what you get if you use the keyword as a parameter.
 // To discover new keyword numbers , use the <$ YOURKEYWORD> command
-const int16_t HASH_KEYWORD_PROG = -29718;
 const int16_t HASH_KEYWORD_MAIN = 11339;
-const int16_t HASH_KEYWORD_JOIN = -30750;
 const int16_t HASH_KEYWORD_CABS = -11981;
 const int16_t HASH_KEYWORD_RAM = 25982;
 const int16_t HASH_KEYWORD_CMD = 9962;
@@ -63,7 +62,11 @@ const int16_t HASH_KEYWORD_ACK = 3113;
 const int16_t HASH_KEYWORD_ON = 2657;
 const int16_t HASH_KEYWORD_DCC = 6436;
 const int16_t HASH_KEYWORD_SLOW = -17209;
+#ifndef DISABLE_PROG
+const int16_t HASH_KEYWORD_JOIN = -30750;
+const int16_t HASH_KEYWORD_PROG = -29718;
 const int16_t HASH_KEYWORD_PROGBOOST = -6353;
+#endif
 #ifndef DISABLE_EEPROM
 const int16_t HASH_KEYWORD_EEPROM = -7168;
 #endif
@@ -285,6 +288,8 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)

        if (direction < 0 || direction > 1)
            break; // invalid direction code
+	if (cab > 10239 || cab < 0)
+	    break; // beyond DCC range

        DCC::setThrottle(cab, tspeed, direction);
        if (params == 4) // send obsolete format T response
@@ -368,6 +373,7 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
            return;
        break;

+#ifndef DISABLE_PROG
    case 'w': // WRITE CV on MAIN <w CAB CV VALUE>
        DCC::writeCVByteMain(p[0], p[1], p[2]);
        return;
@@ -375,9 +381,12 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
    case 'b': // WRITE CV BIT ON MAIN <b CAB CV BIT VALUE>
        DCC::writeCVBitMain(p[0], p[1], p[2], p[3]);
        return;
+#endif

    case 'M': // WRITE TRANSPARENT DCC PACKET MAIN <M REG X1 ... X9>
+#ifndef DISABLE_PROG
    case 'P': // WRITE TRANSPARENT DCC PACKET PROG <P REG X1 ... X9>
+#endif
        // NOTE: this command was parsed in HEX instead of decimal
        params--; // drop REG
        if (params<1) break;
@@ -392,6 +401,7 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
        }
        return;
        
+#ifndef DISABLE_PROG
    case 'W': // WRITE CV ON PROG <W CV VALUE CALLBACKNUM CALLBACKSUB>
            if (!stashCallback(stream, p, ringStream))
                break;
@@ -449,6 +459,7 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
            return;
        }
        break;
+#endif

    case '1': // POWERON <1   [MAIN|PROG|JOIN]>
        {
@@ -461,17 +472,19 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
            prog=true;
        }
 	if (params==1) {
-	  if (p[0] == HASH_KEYWORD_JOIN) {  // <1 JOIN>
+	  if (p[0]==HASH_KEYWORD_MAIN) { // <1 MAIN>
+            main=true;
+	  }
+#ifndef DISABLE_PROG
+	  else if (p[0] == HASH_KEYWORD_JOIN) {  // <1 JOIN>
            main=true;
            prog=true;
            join=true;
 	  }
-	  else if (p[0]==HASH_KEYWORD_MAIN) { // <1 MAIN>
-            main=true;
-	  }
 	  else if (p[0]==HASH_KEYWORD_PROG) { // <1 PROG>
            prog=true;
 	  }
+#endif
 	  else break; // will reply <X>
 	}
        if (main) TrackManager::setMainPower(POWERMODE::ON);
@@ -495,9 +508,11 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
 	  if (p[0]==HASH_KEYWORD_MAIN) { // <0 MAIN>
 	    main=true;
 	  }
+#ifndef DISABLE_PROG
 	  else if (p[0]==HASH_KEYWORD_PROG) { // <0 PROG>
 	    prog=true;
 	  }
+#endif
 	  else break; // will reply <X>
 	}

@@ -637,8 +652,12 @@ void DCCEXParser::parseOne(Print *stream, byte *com, RingStream * ringStream)
                if (params==1) {
                    SENDFLASHLIST(stream,RMFT2::rosterIdList)
                }
-                else StringFormatter::send(stream,F(" %d \"%S\" \"%S\""), 
-                    id, RMFT2::getRosterName(id), RMFT2::getRosterFunctions(id));
+                else {
+		  const FSH * functionNames= RMFT2::getRosterFunctions(id);
+		  StringFormatter::send(stream,F(" %d \"%S\" \"%S\""), 
+					id, RMFT2::getRosterName(id),
+					functionNames == NULL ? RMFT2::getRosterFunctions(0) : functionNames);
+		}
 #endif          
                StringFormatter::send(stream, F(">\n"));      
                return; 
@@ -892,6 +911,7 @@ bool DCCEXParser::parseD(Print *stream, int16_t params, int16_t p[])
        StringFormatter::send(stream, F("Free memory=%d\n"), DCCTimer::getMinimumFreeMemory());
        break;

+#ifndef DISABLE_PROG
    case HASH_KEYWORD_ACK: // <D ACK ON/OFF> <D ACK [LIMIT|MIN|MAX|RETRY] Value>
 	if (params >= 3) {
 	    if (p[1] == HASH_KEYWORD_LIMIT) {
@@ -912,6 +932,7 @@ bool DCCEXParser::parseD(Print *stream, int16_t params, int16_t p[])
 	  Diag::ACK = onOff;
 	}
        return true;
+#endif

    case HASH_KEYWORD_CMD: // <D CMD ON/OFF>
        Diag::CMD = onOff;
@@ -934,11 +955,11 @@ bool DCCEXParser::parseD(Print *stream, int16_t params, int16_t p[])
        Diag::LCN = onOff;
        return true;
 #endif
-
+#ifndef DISABLE_PROG
    case HASH_KEYWORD_PROGBOOST:
        TrackManager::progTrackBoosted=true;
 	    return true;
-
+#endif
    case HASH_KEYWORD_RESET:
        DCCTimer::reset();
        break; // and <X> if we didnt restart 
--- a/DCCTimer.h
+++ b/DCCTimer.h
@@ -1,7 +1,7 @@
 /*
- *  © 2022 Paul M. Antoine
+ *  © 2022-2023 Paul M. Antoine
 *  © 2021 Mike S
- *  © 2021-2022 Harald Barth
+ *  © 2021-2023 Harald Barth
 *  © 2021 Fred Decker
 *  All rights reserved.
 *  
@@ -62,6 +62,9 @@ class DCCTimer {
  static bool isPWMPin(byte pin);
  static void setPWM(byte pin, bool high);
  static void clearPWM();
+  static void DCCEXanalogWriteFrequency(uint8_t pin, uint32_t frequency);
+  static void DCCEXanalogWrite(uint8_t pin, int value);
+
 // Update low ram level.  Allow for extra bytes to be specified
 // by estimation or inspection, that may be used by other 
 // called subroutines.  Must be called with interrupts disabled.
--- a/DCCTimerESP.cpp
+++ b/DCCTimerESP.cpp
@@ -150,6 +150,45 @@ int DCCTimer::freeMemory() {
 void DCCTimer::reset() {
   ESP.restart();
 }
+
+#include "esp32-hal.h"
+#include "soc/soc_caps.h"
+
+
+#ifdef SOC_LEDC_SUPPORT_HS_MODE
+#define LEDC_CHANNELS           (SOC_LEDC_CHANNEL_NUM<<1)
+#else
+#define LEDC_CHANNELS           (SOC_LEDC_CHANNEL_NUM)
+#endif
+
+static int8_t pin_to_channel[SOC_GPIO_PIN_COUNT] = { 0 };
+static int cnt_channel = LEDC_CHANNELS;
+
+void DCCTimer::DCCEXanalogWriteFrequency(uint8_t pin, uint32_t frequency) {
+  if (pin < SOC_GPIO_PIN_COUNT) {
+    if (pin_to_channel[pin] != 0) {
+      ledcSetup(pin_to_channel[pin], frequency, 8);
+    }
+  }
+}
+
+void DCCTimer::DCCEXanalogWrite(uint8_t pin, int value) {
+  if (pin < SOC_GPIO_PIN_COUNT) {
+    if (pin_to_channel[pin] == 0) {
+      if (!cnt_channel) {
+          log_e("No more PWM channels available! All %u already used", LEDC_CHANNELS);
+          return;
+      }
+      pin_to_channel[pin] = --cnt_channel;
+      ledcAttachPin(pin, cnt_channel);
+      ledcSetup(cnt_channel, 1000, 8);
+    } else {
+      ledcAttachPin(pin, pin_to_channel[pin]);
+    }
+    ledcWrite(pin_to_channel[pin], value);
+  }
+}
+
 int ADCee::init(uint8_t pin) {
  pinMode(pin, ANALOG);
  adc1_config_width(ADC_WIDTH_BIT_12);
--- a/DCCTimerSTM32.cpp
+++ b/DCCTimerSTM32.cpp
@@ -1,8 +1,8 @@
 /*
 *  © 2023 Neil McKechnie
- *  © 2022 Paul M. Antoine
+ *  © 2022-23 Paul M. Antoine
 *  © 2021 Mike S
- *  © 2021 Harald Barth
+ *  © 2021, 2023 Harald Barth
 *  © 2021 Fred Decker
 *  © 2021 Chris Harlow
 *  © 2021 David Cutting
@@ -30,6 +30,10 @@
 #ifdef ARDUINO_ARCH_STM32

 #include "DCCTimer.h"
+#ifdef DEBUG_ADC
+#include "TrackManager.h"
+#endif
+#include "DIAG.h"

 #if defined(ARDUINO_NUCLEO_F411RE)
 // Nucleo-64 boards don't have Serial1 defined by default
@@ -37,17 +41,22 @@ HardwareSerial Serial1(PB7, PA15);  // Rx=PB7, Tx=PA15 -- CN7 pins 17 and 21 - F
 // Serial2 is defined to use USART2 by default, but is in fact used as the diag console
 // via the debugger on the Nucleo-64. It is therefore unavailable for other DCC-EX uses like WiFi, DFPlayer, etc.
 // Let's define Serial6 as an additional serial port (the only other option for the Nucleo-64s)
-HardwareSerial Serial6(PA12, PA11);  // Rx=PA12, Tx=PA11 -- CN10 pins 12 and 14 - F411RE
+HardwareSerial Serial3(PA12, PA11);  // Rx=PA12, Tx=PA11 -- CN10 pins 12 and 14 - F411RE
 #elif defined(ARDUINO_NUCLEO_F446RE)
 // Nucleo-64 boards don't have Serial1 defined by default
-HardwareSerial Serial1(PA10, PB6);  // Rx=PA10 (D2), Tx=PB6 (D10) -- CN10 pins 17 and 9 - F446RE 
+// HardwareSerial Serial1(PA10, PB6);  // Rx=PA10 (D2), Tx=PB6 (D10) -- CN10 pins 17 and 9 - F446RE 
 // Serial2 is defined to use USART2 by default, but is in fact used as the diag console
 // via the debugger on the Nucleo-64. It is therefore unavailable for other DCC-EX uses like WiFi, DFPlayer, etc.
+HardwareSerial Serial1(PC11, PC10);  // Rx=PC11, Tx=PC10 -- USART3 - F446RE
+HardwareSerial Serial3(PD2, PC12);  // Rx=PC7, Tx=PC6 -- UART5 - F446RE
+// NB: USART3 and USART6 are available but as yet undefined
 #elif defined(ARDUINO_NUCLEO_F412ZG) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
 // Nucleo-144 boards don't have Serial1 defined by default
-HardwareSerial Serial1(PG9, PG14);  // Rx=PG9, Tx=PG14 -- D0, D1 - F412ZG/F446ZE
+HardwareSerial Serial1(PG9, PG14);  // Rx=PG9, Tx=PG14 -- USART6
+// Serial3 is defined to use USART3 by default, but is in fact used as the diag console
+// via the debugger on the Nucleo-144. It is therefore unavailable for other DCC-EX uses like WiFi, DFPlayer, etc.
 #else
-#warning Serial1 not defined
+#error STM32 board selected is not yet explicitly supported - so Serial1 peripheral is not defined
 #endif

 ///////////////////////////////////////////////////////////////////////////////////////////////
@@ -227,6 +236,9 @@ void DCCTimer::reset() {
 #define NUM_ADC_INPUTS NUM_ANALOG_INPUTS

 // TODO: may need to use uint32_t on STMF4xx variants with > 16 analog inputs!
+#if defined(ARDUINO_NUCLEO_F446RE) || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F446ZE)
+#warning STM32 board selected not fully supported - only use ADC1 inputs 0-15 for current sensing!
+#endif
 uint16_t ADCee::usedpins = 0;
 int * ADCee::analogvals = NULL;
 uint32_t * analogchans = NULL;
@@ -237,10 +249,13 @@ int16_t ADCee::ADCmax() {
 }

 int ADCee::init(uint8_t pin) {
-  uint8_t id = pin - A0;
+
  int value = 0;
-  PinName stmpin = digitalPin[analogInputPin[id]];
-  uint32_t stmgpio = stmpin / 16; // 16-bits per GPIO port group on STM32
+  PinName stmpin = analogInputToPinName(pin);
+  if (stmpin == NC) // do not continue if this is not an analog pin at all
+    return -1024;   // some silly value as error
+
+  uint32_t stmgpio = STM_PORT(stmpin); // converts to the GPIO port (16-bits per port group on STM32)
  uint32_t adcchan =  STM_PIN_CHANNEL(pinmap_function(stmpin, PinMap_ADC)); // find ADC channel (only valid for ADC1!)
  GPIO_TypeDef * gpioBase;

@@ -258,12 +273,20 @@ int ADCee::init(uint8_t pin) {
        RCC->AHB1ENR |= RCC_AHB1ENR_GPIOCEN; //Power up PORTC
        gpioBase = GPIOC;
        break;
+    default:
+      return -1023; // some silly value as error
  }

-  // Set pin mux mode to analog input
-  gpioBase->MODER |= (0b011 << (stmpin << 1)); // Set pin mux to analog mode
+  // Set pin mux mode to analog input, the 32 bit port mode register has 2 bits per pin
+  gpioBase->MODER |= (0b011 << (STM_PIN(stmpin) << 1)); // Set pin mux to analog mode (binary 11)

  // Set the sampling rate for that analog input
+  // This is F411x specific! Different on for example F334
+  // STM32F11xC/E Reference manual
+  // 11.12.4 ADC sample time register 1 (ADC_SMPR1) (channels 10 to 18)
+  // 11.12.5 ADC sample time register 2 (ADC_SMPR2) (channels 0 to 9)
+  if (adcchan > 18)
+    return -1022; // silly value as error
  if (adcchan < 10)
    ADC1->SMPR2 |= (0b111 << (adcchan * 3)); // Channel sampling rate 480 cycles
  else
@@ -275,8 +298,12 @@ int ADCee::init(uint8_t pin) {
  while(!(ADC1->SR & (1 << 1)));  // Wait until conversion is complete
  value = ADC1->DR;               // Read value from register

-  if (analogvals == NULL)
-  {
+  uint8_t id = pin - PNUM_ANALOG_BASE;
+  if (id > 15) { // today we have not enough bits in the mask to support more
+    return -1021;
+  }
+
+  if (analogvals == NULL) {  // allocate analogvals and analogchans if this is the first invocation of init.
    analogvals = (int *)calloc(NUM_ADC_INPUTS+1, sizeof(int));
    analogchans = (uint32_t *)calloc(NUM_ADC_INPUTS+1, sizeof(uint32_t));
  }
@@ -284,6 +311,8 @@ int ADCee::init(uint8_t pin) {
  analogchans[id] = adcchan;  // Keep track of which ADC channel is used for reading this pin
  usedpins |= (1 << id);      // This pin is now ready

+  DIAG(F("ADCee::init(): value=%d, channel=%d, id=%d"), value, adcchan, id);
+
  return value;
 }

@@ -291,7 +320,7 @@ int ADCee::init(uint8_t pin) {
 * Read function ADCee::read(pin) to get value instead of analogRead(pin)
 */
 int ADCee::read(uint8_t pin, bool fromISR) {
-  uint8_t id = pin - A0;
+  uint8_t id = pin - PNUM_ANALOG_BASE;
  // Was this pin initialised yet?
  if ((usedpins & (1<<id) ) == 0)
    return -1023;
@@ -306,7 +335,7 @@ int ADCee::read(uint8_t pin, bool fromISR) {
 #pragma GCC push_options
 #pragma GCC optimize ("-O3")
 void ADCee::scan() {
-  static uint8_t id = 0;        // id and mask are the same thing but it is faster to 
+  static uint8_t id = 0;     // id and mask are the same thing but it is faster to
  static uint16_t mask = 1;  // increment and shift instead to calculate mask from id
  static bool waiting = false;

@@ -317,11 +346,13 @@ void ADCee::scan() {
    // found value
    analogvals[id] = ADC1->DR;
    // advance at least one track
-    // for scope debug TrackManager::track[1]->setBrake(0);
+#ifdef DEBUG_ADC
+    if (id == 1) TrackManager::track[1]->setBrake(0);
+#endif
    waiting = false;
    id++;
    mask = mask << 1;
-    if (id == NUM_ADC_INPUTS+1) {
+    if (mask == 0) { // the 1 has been shifted out
      id = 0;
      mask = 1;
    }
@@ -332,18 +363,20 @@ void ADCee::scan() {
    // look for a valid track to sample or until we are around
    while (true) {
      if (mask  & usedpins) {
-    	  // start new ADC aquire on id
+	// start new ADC aquire on id
        ADC1->SQR3 = analogchans[id]; //1st conversion in regular sequence
        ADC1->CR2 |= (1 << 30); //Start 1st conversion SWSTART
-	      // for scope debug TrackManager::track[1]->setBrake(1);
-	      waiting = true;
-	      return;
+#ifdef DEBUG_ADC
+	if (id == 1) TrackManager::track[1]->setBrake(1);
+#endif
+	waiting = true;
+	return;
      }
      id++;
      mask = mask << 1;
-      if (id == NUM_ADC_INPUTS+1) {
-	      id = 0;
-	      mask = 1;
+      if (mask == 0) { // the 1 has been shifted out
+	id = 0;
+	mask = 1;
      }
    }
  }
@@ -368,4 +401,4 @@ void ADCee::begin() {
  ADC1->CR2 |= (1 << 0); // Switch on ADC1
  interrupts();
 }
-#endif
+#endif
--- a/ESP32-fixes.cpp
+++ b/ESP32-fixes.cpp
@@ -1,61 +0,0 @@
-/*
- *  © 2022 Harald Barth
- *  All rights reserved.
- *  
- *  This file is part of CommandStation-EX
- *
- *  This is free software: you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation, either version 3 of the License, or
- *  (at your option) any later version.
- *
- *  It is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
- */
-#ifdef ARDUINO_ARCH_ESP32
-#include <Arduino.h>
-#include "ESP32-fixes.h"
-
-#include "esp32-hal.h"
-#include "soc/soc_caps.h"
-
-
-#ifdef SOC_LEDC_SUPPORT_HS_MODE
-#define LEDC_CHANNELS           (SOC_LEDC_CHANNEL_NUM<<1)
-#else
-#define LEDC_CHANNELS           (SOC_LEDC_CHANNEL_NUM)
-#endif
-
-static int8_t pin_to_channel[SOC_GPIO_PIN_COUNT] = { 0 };
-static int cnt_channel = LEDC_CHANNELS;
-
-void DCCEXanalogWriteFrequency(uint8_t pin, uint32_t frequency) {
-  if (pin < SOC_GPIO_PIN_COUNT) {
-    if (pin_to_channel[pin] != 0) {
-      ledcSetup(pin_to_channel[pin], frequency, 8);
-    }
-  }
-}
-
-void DCCEXanalogWrite(uint8_t pin, int value) {
-  if (pin < SOC_GPIO_PIN_COUNT) {
-    if (pin_to_channel[pin] == 0) {
-      if (!cnt_channel) {
-          log_e("No more PWM channels available! All %u already used", LEDC_CHANNELS);
-          return;
-      }
-      pin_to_channel[pin] = --cnt_channel;
-      ledcAttachPin(pin, cnt_channel);
-      ledcSetup(cnt_channel, 1000, 8);
-    } else {
-      ledcAttachPin(pin, pin_to_channel[pin]);
-    }
-    ledcWrite(pin_to_channel[pin], value);
-  }
-}
-#endif
--- a/ESP32-fixes.h
+++ b/ESP32-fixes.h
@@ -1,26 +0,0 @@
-/*
- *  © 2022 Harald Barth
- *  All rights reserved.
- *  
- *  This file is part of CommandStation-EX
- *
- *  This is free software: you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License as published by
- *  the Free Software Foundation, either version 3 of the License, or
- *  (at your option) any later version.
- *
- *  It is distributed in the hope that it will be useful,
- *  but WITHOUT ANY WARRANTY; without even the implied warranty of
- *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *  GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
- */
-#ifdef ARDUINO_ARCH_ESP32
-#pragma once
-#include <Arduino.h>
-void DCCEXanalogWriteFrequency(uint8_t pin, uint32_t frequency);
-void DCCEXanalogWrite(uint8_t pin, int value);
-#endif
-
--- a/EX-CommandStation-installer.exe
+++ b/EX-CommandStation-installer.exe
--- a/EXRAIL2.cpp
+++ b/EXRAIL2.cpp
@@ -2,6 +2,7 @@
 *  © 2021 Neil McKechnie
 *  © 2021-2023 Harald Barth
 *  © 2020-2023 Chris Harlow
+ *  © 2022 Colin Murdoch
 *  All rights reserved.
 *  
 *  This file is part of CommandStation-EX
@@ -265,16 +266,17 @@ void RMFT2::setTurnoutHiddenState(Turnout * t) {
 char RMFT2::getRouteType(int16_t id) {
  for (int16_t i=0;;i+=2) {
    int16_t rid= GETHIGHFLASHW(routeIdList,i);
+    if (rid==INT16_MAX) break;
    if (rid==id) return 'R';
-    if (rid==0) break;
  }
  for (int16_t i=0;;i+=2) {
    int16_t rid= GETHIGHFLASHW(automationIdList,i);
+    if (rid==INT16_MAX) break;
    if (rid==id) return 'A';
-    if (rid==0) break;
  }
  return 'X';
-}   
+}
+
 // This filter intercepts <> commands to do the following:
 // - Implement RMFT specific commands/diagnostics
 // - Reject/modify JMRI commands that would interfere with RMFT processing
@@ -608,6 +610,7 @@ void RMFT2::loop2() {
      break;
      
  case OPCODE_SPEED:
+    forward=DCC::getThrottleDirection(loco)^invert;
    driveLoco(operand);
    break;
    
@@ -702,11 +705,11 @@ void RMFT2::loop2() {
    DCC::setThrottle(0,1,true);  // pause all locos on the track
    pausingTask=this;
    break;
-    
+
  case OPCODE_POM:
    if (loco) DCC::writeCVByteMain(loco, operand, getOperand(1));
    break;
-    
+
  case OPCODE_POWEROFF:
    TrackManager::setPower(POWERMODE::OFF);
    TrackManager::setJoin(false);
@@ -881,23 +884,18 @@ void RMFT2::loop2() {
    while(loopTask) loopTask->kill(F("KILLALL"));
    return;

+#ifndef DISABLE_PROG
  case OPCODE_JOIN:
    TrackManager::setPower(POWERMODE::ON);
    TrackManager::setJoin(true);
    CommandDistributor::broadcastPower();
    break;
-    
-  case OPCODE_POWERON:
-    TrackManager::setMainPower(POWERMODE::ON);
-    TrackManager::setJoin(false);
-    CommandDistributor::broadcastPower();
-    break;
-    
+
  case OPCODE_UNJOIN:
    TrackManager::setJoin(false);
    CommandDistributor::broadcastPower();
    break;
-    
+
  case OPCODE_READ_LOCO1: // READ_LOCO is implemented as 2 separate opcodes
    progtrackLocoId=LOCO_ID_WAITING;  // Nothing found yet
    DCC::getLocoId(readLocoCallback);
@@ -918,6 +916,13 @@ void RMFT2::loop2() {
    forward=true;
    invert=false;
    break;
+#endif
+
+  case OPCODE_POWERON:
+    TrackManager::setMainPower(POWERMODE::ON);
+    TrackManager::setJoin(false);
+    CommandDistributor::broadcastPower();
+    break;
    
  case OPCODE_START:
    {
@@ -1129,7 +1134,10 @@ void RMFT2::clockEvent(int16_t clocktime, bool change) {
  // Hunt for an ONTIME for this time
  if (Diag::CMD)
   DIAG(F("Looking for clock event at : %d"), clocktime);
-  if (change)  handleEvent(F("CLOCK"),onClockLookup,clocktime);
+  if (change) {
+    handleEvent(F("CLOCK"),onClockLookup,clocktime);
+    handleEvent(F("CLOCK"),onClockLookup,25*60+clocktime%60);
+  }
 } 

 void RMFT2::handleEvent(const FSH* reason,LookList* handlers, int16_t id) {
@@ -1237,7 +1245,10 @@ void RMFT2::thrungeString(uint32_t strfar, thrunger mode, byte id) {
      DCCEXParser::parseOne(&USB_SERIAL,(byte*)buffer->getString(),NULL);
      break;
    case thrunge_broadcast:
-  // TODO     CommandDistributor::broadcastText(buffer->getString());
+      CommandDistributor::broadcastRaw(CommandDistributor::COMMAND_TYPE,buffer->getString());
+      break;
+    case thrunge_withrottle:
+      CommandDistributor::broadcastRaw(CommandDistributor::WITHROTTLE_TYPE,buffer->getString());
      break;
    case thrunge_lcd:
         LCD(id,F("%s"),buffer->getString());
--- a/EXRAIL2.h
+++ b/EXRAIL2.h
@@ -1,6 +1,7 @@
 /*
 *  © 2021 Neil McKechnie
 *  © 2020-2022 Chris Harlow
+ *  © 2022 Colin Murdoch
 *  © 2023 Harald Barth
 *  All rights reserved.
 *  
@@ -44,7 +45,10 @@ enum OPCODE : byte {OPCODE_THROW,OPCODE_CLOSE,
             OPCODE_RED,OPCODE_GREEN,OPCODE_AMBER,OPCODE_DRIVE,
             OPCODE_SERVO,OPCODE_SIGNAL,OPCODE_TURNOUT,OPCODE_WAITFOR,
             OPCODE_PAD,OPCODE_FOLLOW,OPCODE_CALL,OPCODE_RETURN,
-             OPCODE_JOIN,OPCODE_UNJOIN,OPCODE_READ_LOCO1,OPCODE_READ_LOCO2,OPCODE_POM,
+#ifndef DISABLE_PROG
+             OPCODE_JOIN,OPCODE_UNJOIN,OPCODE_READ_LOCO1,OPCODE_READ_LOCO2,
+#endif
+             OPCODE_POM,
             OPCODE_START,OPCODE_SETLOCO,OPCODE_SENDLOCO,OPCODE_FORGET,
             OPCODE_PAUSE, OPCODE_RESUME,OPCODE_POWEROFF,OPCODE_POWERON,
             OPCODE_ONCLOSE, OPCODE_ONTHROW, OPCODE_SERVOTURNOUT, OPCODE_PINTURNOUT,
@@ -76,7 +80,8 @@ enum OPCODE : byte {OPCODE_THROW,OPCODE_CLOSE,
 // Ensure thrunge_lcd is put last as there may be more than one display, 
 // sequentially numbered from thrunge_lcd.
 enum thrunger: byte {
-  thrunge_print, thrunge_broadcast, thrunge_serial,thrunge_parse,
+  thrunge_print, thrunge_broadcast, thrunge_withrottle,
+  thrunge_serial,thrunge_parse,
  thrunge_serial1, thrunge_serial2, thrunge_serial3,
  thrunge_serial4, thrunge_serial5, thrunge_serial6,
  thrunge_lcn, 
--- a/EXRAIL2MacroReset.h
+++ b/EXRAIL2MacroReset.h
@@ -1,5 +1,6 @@
 /*
 *  © 2020-2022 Chris Harlow. All rights reserved.
+ *  © 2022 Colin Murdoch
 *  © 2023 Harald Barth
 *  
 *  This file is part of CommandStation-EX
@@ -91,6 +92,7 @@
 #undef ONCLOSE
 #undef ONTIME
 #undef ONCLOCKTIME
+#undef ONCLOCKMINS
 #undef ONGREEN
 #undef ONRED
 #undef ONTHROW 
@@ -99,7 +101,9 @@
 #undef PAUSE
 #undef PIN_TURNOUT 
 #undef PRINT
+#ifndef DISABLE_PROG
 #undef POM
+#endif
 #undef POWEROFF
 #undef POWERON
 #undef READ_LOCO 
@@ -134,11 +138,13 @@
 #undef STOP 
 #undef THROW  
 #undef TURNOUT 
+#undef TURNOUTL
 #undef UNJOIN
 #undef UNLATCH 
 #undef VIRTUAL_SIGNAL
 #undef VIRTUAL_TURNOUT
 #undef WAITFOR
+#undef WITHROTTLE
 #undef XFOFF
 #undef XFON

@@ -208,6 +214,7 @@
 #define ONAMBER(signal_id) 
 #define ONTIME(value)
 #define ONCLOCKTIME(hours,mins)
+#define ONCLOCKMINS(mins)
 #define ONDEACTIVATE(addr,subaddr)
 #define ONDEACTIVATEL(linear) 
 #define ONCLOSE(turnout_id)
@@ -219,7 +226,9 @@
 #define PIN_TURNOUT(id,pin,description...) 
 #define PRINT(msg) 
 #define PARSE(msg)
+#ifndef DISABLE_PROG
 #define POM(cv,value)
+#endif
 #define POWEROFF
 #define POWERON
 #define READ_LOCO 
@@ -254,11 +263,13 @@
 #define STOP 
 #define THROW(id)  
 #define TURNOUT(id,addr,subaddr,description...) 
+#define TURNOUTL(id,addr,description...) 
 #define UNJOIN 
 #define UNLATCH(sensor_id) 
 #define VIRTUAL_SIGNAL(id) 
 #define VIRTUAL_TURNOUT(id,description...) 
 #define WAITFOR(pin)
+#define WITHROTTLE(msg)
 #define XFOFF(cab,func)
 #define XFON(cab,func)
 #endif
--- a/EXRAILMacros.h
+++ b/EXRAILMacros.h
@@ -1,6 +1,7 @@
 /*
 *  © 2021 Neil McKechnie
 *  © 2020-2022 Chris Harlow
+ *  © 2022 Colin Murdoch
 *  © 2023 Harald Barth
 *  All rights reserved.
 *  
@@ -80,14 +81,14 @@ void exrailHalSetup() {
 #define ROUTE(id, description) id,
 const int16_t HIGHFLASH RMFT2::routeIdList[]= {
    #include "myAutomation.h"
-    0}; 
+    INT16_MAX};
 // Pass 2a create throttle automation list 
 #include "EXRAIL2MacroReset.h"
 #undef AUTOMATION
 #define AUTOMATION(id, description) id,
 const int16_t HIGHFLASH RMFT2::automationIdList[]= {
    #include "myAutomation.h"
-    0}; 
+    INT16_MAX};

 // Pass 3 Create route descriptions:
 #undef ROUTE
@@ -152,6 +153,8 @@ const int StringMacroTracker1=__COUNTER__;
         lcdid=id;\
         break;\
      } 
+#undef WITHROTTLE
+#define WITHROTTLE(msg) THRUNGE(msg,thrunge_withrottle)

 void  RMFT2::printMessage(uint16_t id) { 
  thrunger tmode;
@@ -187,7 +190,7 @@ const FSH * RMFT2::getTurnoutDescription(int16_t turnoutid) {
 // Pass 6: Roster IDs (count)
 #include "EXRAIL2MacroReset.h"
 #undef ROSTER
-#define ROSTER(cabid,name,funcmap...) +1
+#define ROSTER(cabid,name,funcmap...) +(cabid <= 0 ? 0 : 1)
 const byte RMFT2::rosterNameCount=0
   #include "myAutomation.h"
   ;
@@ -198,7 +201,7 @@ const byte RMFT2::rosterNameCount=0
 #define ROSTER(cabid,name,funcmap...) cabid,
 const int16_t HIGHFLASH  RMFT2::rosterIdList[]={
   #include "myAutomation.h"
-   0};
+   INT16_MAX};

 // Pass 7: Roster names getter
 #include "EXRAIL2MacroReset.h"
@@ -220,7 +223,7 @@ const FSH * RMFT2::getRosterFunctions(int16_t id) {
      #include "myAutomation.h"
   default: break; 
   }   
-   return F("");
+   return NULL;
 } 

 // Pass 8 Signal definitions
@@ -316,6 +319,7 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define ONCLOSE(turnout_id) OPCODE_ONCLOSE,V(turnout_id),
 #define ONTIME(value) OPCODE_ONTIME,V(value),  
 #define ONCLOCKTIME(hours,mins) OPCODE_ONTIME,V((STRIP_ZERO(hours)*60)+STRIP_ZERO(mins)),
+#define ONCLOCKMINS(mins) ONCLOCKTIME(25,mins)
 #define ONDEACTIVATE(addr,subaddr) OPCODE_ONDEACTIVATE,V(addr<<2|subaddr),
 #define ONDEACTIVATEL(linear) OPCODE_ONDEACTIVATE,V(linear+3),
 #define ONGREEN(signal_id) OPCODE_ONGREEN,V(signal_id),
@@ -323,8 +327,10 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define ONTHROW(turnout_id) OPCODE_ONTHROW,V(turnout_id),
 #define ONCHANGE(sensor_id) OPCODE_ONCHANGE,V(sensor_id),
 #define PAUSE OPCODE_PAUSE,0,0,
-#define PIN_TURNOUT(id,pin,description...) OPCODE_PINTURNOUT,V(id),OPCODE_PAD,V(pin), 
+#define PIN_TURNOUT(id,pin,description...) OPCODE_PINTURNOUT,V(id),OPCODE_PAD,V(pin),
+#ifndef DISABLE_PROG
 #define POM(cv,value) OPCODE_POM,V(cv),OPCODE_PAD,V(value),
+#endif
 #define POWEROFF OPCODE_POWEROFF,0,0,
 #define POWERON OPCODE_POWERON,0,0,
 #define PRINT(msg) OPCODE_PRINT,V(__COUNTER__ - StringMacroTracker2),
@@ -361,10 +367,12 @@ const  HIGHFLASH  int16_t RMFT2::SignalDefinitions[] = {
 #define STOP OPCODE_SPEED,V(0), 
 #define THROW(id)  OPCODE_THROW,V(id),
 #define TURNOUT(id,addr,subaddr,description...) OPCODE_TURNOUT,V(id),OPCODE_PAD,V(addr),OPCODE_PAD,V(subaddr),
+#define TURNOUTL(id,addr,description...) TURNOUT(id,(addr-1)/4+1,(addr-1)%4, description)
 #define UNJOIN OPCODE_UNJOIN,0,0,
 #define UNLATCH(sensor_id) OPCODE_UNLATCH,V(sensor_id),
 #define VIRTUAL_SIGNAL(id) 
 #define VIRTUAL_TURNOUT(id,description...) OPCODE_PINTURNOUT,V(id),OPCODE_PAD,V(0), 
+#define WITHROTTLE(msg) PRINT(msg)
 #define WAITFOR(pin) OPCODE_WAITFOR,V(pin),
 #define XFOFF(cab,func) OPCODE_XFOFF,V(cab),OPCODE_PAD,V(func),
 #define XFON(cab,func) OPCODE_XFON,V(cab),OPCODE_PAD,V(func),
--- a/GITHUB_SHA.h
+++ b/GITHUB_SHA.h
@@ -1 +1 @@
-#define GITHUB_SHA "devel-202304071845Z"
+#define GITHUB_SHA "devel-202306190642Z"
--- a/MotorDriver.cpp
+++ b/MotorDriver.cpp
@@ -1,8 +1,8 @@
 /*
- *  © 2022 Paul M Antoine
+ *  © 2022-2023 Paul M Antoine
 *  © 2021 Mike S
 *  © 2021 Fred Decker
- *  © 2020-2022 Harald Barth
+ *  © 2020-2023 Harald Barth
 *  © 2020-2021 Chris Harlow
 *  All rights reserved.
 *  
@@ -27,19 +27,16 @@
 #include "DCCTimer.h"
 #include "DIAG.h"

-#if defined(ARDUINO_ARCH_ESP32)
-#include "ESP32-fixes.h"
-#endif
-
 bool MotorDriver::commonFaultPin=false;

 volatile portreg_t shadowPORTA;
 volatile portreg_t shadowPORTB;
 volatile portreg_t shadowPORTC;

-MotorDriver::MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, int8_t brake_pin,
-                         byte current_pin, float sense_factor, unsigned int trip_milliamps, byte fault_pin) {
-  powerPin=power_pin;
+MotorDriver::MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, int16_t brake_pin,
+                         byte current_pin, float sense_factor, unsigned int trip_milliamps, int16_t fault_pin) {
+  const FSH * warnString = F("** WARNING **");
+
  invertPower=power_pin < 0;
  if (invertPower) {
    powerPin = 0-power_pin;
@@ -95,25 +92,43 @@ MotorDriver::MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, i
  }
  else dualSignal=false; 
  
-  brakePin=brake_pin;
  if (brake_pin!=UNUSED_PIN){
    invertBrake=brake_pin < 0;
-    brakePin=invertBrake ? 0-brake_pin : brake_pin;
+    if (invertBrake)
+      brake_pin = 0-brake_pin;
+    if (brake_pin > MAX_PIN)
+      DIAG(F("%S Brake pin %d > %d"), warnString, brake_pin, MAX_PIN);
+    brakePin=(byte)brake_pin;
    getFastPin(F("BRAKE"),brakePin,fastBrakePin);
    // if brake is used for railcom  cutout we need to do PORTX register trick here as well
    pinMode(brakePin, OUTPUT);
    setBrake(true);  // start with brake on in case we hace DC stuff going on
+  } else {
+    brakePin=UNUSED_PIN;
  }
-  else brakePin=UNUSED_PIN;
  
  currentPin=current_pin;
-  if (currentPin!=UNUSED_PIN) ADCee::init(currentPin);
+  if (currentPin!=UNUSED_PIN) {
+    int ret = ADCee::init(currentPin);
+    if (ret < -1010) { // XXX give value a name later
+      DIAG(F("ADCee::init error %d, disable current pin %d"), ret, currentPin);
+      currentPin = UNUSED_PIN;
+    }
+  }
  senseOffset=0; // value can not be obtained until waveform is activated

-  faultPin=fault_pin;
-  if (faultPin != UNUSED_PIN) {
+  if (fault_pin != UNUSED_PIN) {
+    invertFault=fault_pin < 0;
+    if (invertFault)
+      fault_pin =  0-fault_pin;
+    if (fault_pin > MAX_PIN)
+      DIAG(F("%S Fault pin %d > %d"), warnString, fault_pin, MAX_PIN);
+    faultPin=(byte)fault_pin;
+    DIAG(F("Fault pin = %d invert %d"), faultPin, invertFault);
    getFastPin(F("FAULT"),faultPin, 1 /*input*/, fastFaultPin);
    pinMode(faultPin, INPUT);
+  } else {
+      faultPin=UNUSED_PIN;
  }

  // This conversion performed at compile time so the remainder of the code never needs
@@ -135,20 +150,16 @@ MotorDriver::MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, i
  }

  if (currentPin==UNUSED_PIN) 
-    DIAG(F("** WARNING ** No current or short detection"));
+    DIAG(F("%S No current or short detection"), warnString);
  else  {
-    DIAG(F("Track %c, TripValue=%d"), trackLetter, rawCurrentTripValue);
+    DIAG(F("Pin %d Max %dmA (%d)"), currentPin, raw2mA(rawCurrentTripValue), rawCurrentTripValue);

    // self testing diagnostic for the non-float converters... may be removed when happy
    //  DIAG(F("senseFactorInternal=%d raw2mA(1000)=%d mA2Raw(1000)=%d"),
    //   senseFactorInternal, raw2mA(1000),mA2raw(1000));
  }

-  // prepare values for current detection
-  sampleDelay = 0;
-  lastSampleTaken = millis();
  progTripValue = mA2raw(TRIP_CURRENT_PROG); 
-
 }

 bool MotorDriver::isPWMCapable() {
@@ -157,6 +168,7 @@ bool MotorDriver::isPWMCapable() {


 void MotorDriver::setPower(POWERMODE mode) {
+  if (powerMode == mode) return;
  bool on=mode==POWERMODE::ON;
  if (on) {
    // when switching a track On, we need to check the crrentOffset with the pin OFF
@@ -210,12 +222,17 @@ int MotorDriver::getCurrentRaw(bool fromISR) {
  (void)fromISR;
  if (currentPin==UNUSED_PIN) return 0; 
  int current;
-  current = ADCee::read(currentPin, fromISR)-senseOffset;
+  current = ADCee::read(currentPin, fromISR);
+  // here one can diag raw value
+  // if (fromISR == false) DIAG(F("%c: %d"), trackLetter, current);
+  current = current-senseOffset;     // adjust with offset
  if (current<0) current=0-current;
-  if ((faultPin != UNUSED_PIN)  && isLOW(fastFaultPin) && powerMode==POWERMODE::ON)
+  // current >= 0 here, we use negative current as fault pin flag
+  if ((faultPin != UNUSED_PIN) && powerPin) {
+    if (invertFault ? isHIGH(fastFaultPin) : isLOW(fastFaultPin))
      return (current == 0 ? -1 : -current);
+  }
  return current;
-   
 }

 #ifdef ANALOG_READ_INTERRUPT
@@ -270,6 +287,7 @@ void MotorDriver::setDCSignal(byte speedcode) {
 #if defined(ARDUINO_AVR_MEGA) || defined(ARDUINO_AVR_MEGA2560)
  TCCR2B = (TCCR2B & B11111000) | B00000110; // set divisor on timer 2 to result in (approx) 122.55Hz
  TCCR4B = (TCCR4B & B11111000) | B00000100; // same for timer 4 but maxcount and thus divisor differs
+  TCCR5B = (TCCR5B & B11111000) | B00000100; // same for timer 5 which is like timer 4
 #endif
  // spedcoode is a dcc speed & direction
  byte tSpeed=speedcode & 0x7F; // DCC Speed with 0,1 stop and speed steps 2 to 127
@@ -283,7 +301,7 @@ void MotorDriver::setDCSignal(byte speedcode) {
 	f = taurustones[ (tSpeed-2)/2 ] ;
      }
    }
-    DCCEXanalogWriteFrequency(brakePin, f); // set DC PWM frequency to 100Hz XXX May move to setup
+    DCCTimer::DCCEXanalogWriteFrequency(brakePin, f); // set DC PWM frequency to 100Hz XXX May move to setup
  }
 #endif
  if (tSpeed <= 1) brake = 255;
@@ -292,7 +310,7 @@ void MotorDriver::setDCSignal(byte speedcode) {
  if (invertBrake)
    brake=255-brake;
 #if defined(ARDUINO_ARCH_ESP32)
-  DCCEXanalogWrite(brakePin,brake);
+  DCCTimer::DCCEXanalogWrite(brakePin,brake);
 #else
  analogWrite(brakePin,brake);
 #endif
@@ -351,63 +369,123 @@ void  MotorDriver::getFastPin(const FSH* type,int pin, bool input, FASTPIN & res
 }

 void MotorDriver::checkPowerOverload(bool useProgLimit, byte trackno) {
-  if (millis() - lastSampleTaken  < sampleDelay) return;
-  lastSampleTaken = millis();
  int tripValue= useProgLimit?progTripValue:getRawCurrentTripValue();
-  
-  // Trackname for diag messages later
+
  switch (powerMode) {
    case POWERMODE::OFF:
-      sampleDelay = POWER_SAMPLE_OFF_WAIT;
+      if (overloadNow) {
+	// reset overload condition as we have just turned off power
+	// DIAG(F("OVERLOAD POFF OFF"));
+	overloadNow=false;
+	lastPowerChange = micros();
+      }
+      if (microsSinceLastPowerChange() > POWER_SAMPLE_ALL_GOOD) {
+	power_sample_overload_wait = POWER_SAMPLE_OVERLOAD_WAIT;
+      }
      break;
    case POWERMODE::ON:
      // Check current
      lastCurrent=getCurrentRaw();
      if (lastCurrent < 0) {
-	  // We have a fault pin condition to take care of
-	  lastCurrent = -lastCurrent;
-	  setPower(POWERMODE::OVERLOAD); // Turn off, decide later how fast to turn on again
-	  if (commonFaultPin) {
-	      if (lastCurrent < tripValue) {
-		      setPower(POWERMODE::ON); // maybe other track
-	      }
-	      // Write this after the fact as we want to turn on as fast as possible
-	      // because we don't know which output actually triggered the fault pin
-	      DIAG(F("COMMON FAULT PIN ACTIVE: POWERTOGGLE TRACK %c"), trackno + 'A');
-	  } else {
-	    DIAG(F("TRACK %c FAULT PIN ACTIVE - OVERLOAD"), trackno + 'A');
-	      if (lastCurrent < tripValue) {
-		  lastCurrent = tripValue; // exaggerate
-	      }
+	// We have a fault pin condition to take care of
+	if (!overloadNow) {
+	  // turn on overload condition as fault pin has gone active
+	  // DIAG(F("OVERLOAD FPIN ON"));
+	  overloadNow=true;
+	  lastPowerChange = micros();
+	}
+	lastCurrent = -lastCurrent;
+	if (commonFaultPin) {
+	  if (lastCurrent < tripValue) {
+	    // probably other track, do a fast toggle.
+	    setPower(POWERMODE::OVERLOAD); // Turn off, decide later how fast to turn on again
+	    setPower(POWERMODE::ON); // maybe other track
+	    // Write this after the fact as we want to turn on as fast as possible
+	    // because we don't know which output actually triggered the fault pin
+	    DIAG(F("COMMON FAULT PIN ACTIVE: POWERTOGGLE TRACK %c"), trackno + 'A');
 	  }
+	} else {
+	  if (lastCurrent < tripValue) {
+	    if (power_sample_overload_wait <= (POWER_SAMPLE_OVERLOAD_WAIT * 10) &&    // almost virgin
+		microsSinceLastPowerChange() < POWER_SAMPLE_IGNORE_FAULT_LOW) {
+	      // Ignore 50ms fault pin if no current
+	      DIAG(F("TRACK %c FAULT PIN 50ms ignore"), trackno + 'A');
+	      break;
+	    }
+	    lastCurrent = tripValue; // exaggerate so condition below (*) is true
+	  } else {
+	    if (power_sample_overload_wait <= POWER_SAMPLE_OVERLOAD_WAIT &&   // virgin
+		microsSinceLastPowerChange() < POWER_SAMPLE_IGNORE_FAULT_HIGH) {
+              // Ignore 5ms fault pin if we see current
+	      DIAG(F("TRACK %c FAULT PIN 5ms ignore"), trackno + 'A');
+	      break;
+	    }
+	  }
+	  DIAG(F("TRACK %c FAULT PIN ACTIVE"), trackno + 'A');
+	}
      }
-      if (lastCurrent < tripValue) {
-        sampleDelay = POWER_SAMPLE_ON_WAIT;
-	if(power_good_counter<100)
-	  power_good_counter++;
-	else
-	  if (power_sample_overload_wait>POWER_SAMPLE_OVERLOAD_WAIT) power_sample_overload_wait=POWER_SAMPLE_OVERLOAD_WAIT;
+      // // //
+      // above we looked at fault pin, below we look at current
+      // // //
+      if (lastCurrent < tripValue) { // see above (*)
+	if (overloadNow) {
+	  // current is below trip value, turn off overload condition
+	  // DIAG(F("OVERLOAD PON OFF"));
+	  overloadNow=false;
+	  lastPowerChange = micros();
+	}
+	if (microsSinceLastPowerChange() > POWER_SAMPLE_ALL_GOOD) {
+	  power_sample_overload_wait = POWER_SAMPLE_OVERLOAD_WAIT;
+	}
      } else {
-        setPower(POWERMODE::OVERLOAD);
-        unsigned int mA=raw2mA(lastCurrent);
-        unsigned int maxmA=raw2mA(tripValue);
-	      power_good_counter=0;
-        sampleDelay = power_sample_overload_wait;
-        DIAG(F("TRACK %c POWER OVERLOAD %dmA (limit %dmA) shutdown for %dms"), trackno + 'A', mA, maxmA, sampleDelay);
-	if (power_sample_overload_wait >= 10000)
-	    power_sample_overload_wait = 10000;
-	else
-	    power_sample_overload_wait *= 2;
+	// too much current
+	if (!overloadNow) {
+	  // current is over trip value, turn on overload condition
+	  // DIAG(F("OVERLOAD PON ON"));
+	  overloadNow=true;
+	  lastPowerChange = micros();
+	}
+	unsigned long uSecs = microsSinceLastPowerChange();
+	if (power_sample_overload_wait > POWER_SAMPLE_OVERLOAD_WAIT ||    // not virgin
+	    uSecs > POWER_SAMPLE_OFF_DELAY) {
+	  // Overload has existed longer than delay (typ. 10ms)
+	  setPower(POWERMODE::OVERLOAD);
+	  if (overloadNow) {
+	    // the setPower just turned off, so overload is now gone
+	    // DIAG(F("OVERLOAD PON OFF"));
+	    overloadNow=false;
+	    lastPowerChange = micros();
+	  }
+	  unsigned int mA=raw2mA(lastCurrent);
+	  unsigned int maxmA=raw2mA(tripValue);
+	  DIAG(F("TRACK %c POWER OVERLOAD %dmA (limit %dmA) shutdown after %lus for %lus"),
+	       trackno + 'A', mA, maxmA, uSecs, power_sample_overload_wait);
+	}
      }
      break;
-    case POWERMODE::OVERLOAD:
-      // Try setting it back on after the OVERLOAD_WAIT
+  case POWERMODE::OVERLOAD:
+    if (overloadNow) {
+      // state overload mode means power is off, turn off overload condition flag as well
+      // DIAG(F("OVERLOAD POVER OFF"));
+      overloadNow=false;
+      lastPowerChange = micros();
+    }
+    // Try setting it back on after the OVERLOAD_WAIT
+    if (microsSinceLastPowerChange() > power_sample_overload_wait) {
+      // adjust next wait time
+      power_sample_overload_wait *= 2;
+      if (power_sample_overload_wait > POWER_SAMPLE_RETRY_MAX)
+	power_sample_overload_wait = POWER_SAMPLE_RETRY_MAX;
+      // power on test
      setPower(POWERMODE::ON);
-      sampleDelay = POWER_SAMPLE_ON_WAIT;
-      // Debug code....
-      DIAG(F("TRACK %c POWER RESTORE (check %dms)"), trackno + 'A', sampleDelay);
-      break;
-    default:
-      sampleDelay = 999; // cant get here..meaningless statement to avoid compiler warning.
+      // here we change power but not the overloadNow as that was
+      // already changed to false when we entered POWERMODE::OVERLOAD
+      // so we need to set the lastPowerChange anyway.
+      lastPowerChange = micros();
+      DIAG(F("TRACK %c POWER RESTORE (was off %lus)"), trackno + 'A', power_sample_overload_wait);
+    }
+    break;
+  default:
+    break;
  }
 }
--- a/MotorDriver.h
+++ b/MotorDriver.h
@@ -74,8 +74,9 @@
 // Virtualised Motor shield 1-track hardware Interface

 #ifndef UNUSED_PIN     // sync define with the one in MotorDrivers.h
-#define UNUSED_PIN 127 // inside int8_t
+#define UNUSED_PIN 255 // inside uint8_t
 #endif
+#define MAX_PIN 254

 class pinpair {
 public:
@@ -111,8 +112,8 @@ enum class POWERMODE : byte { OFF, ON, OVERLOAD };
 class MotorDriver {
  public:
    
-    MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, int8_t brake_pin, 
-                byte current_pin, float senseFactor, unsigned int tripMilliamps, byte faultPin);
+    MotorDriver(int16_t power_pin, byte signal_pin, byte signal_pin2, int16_t brake_pin, 
+                byte current_pin, float senseFactor, unsigned int tripMilliamps, int16_t fault_pin);
    void setPower( POWERMODE mode);
    POWERMODE getPower() { return powerMode;}
    // as the port registers can be shadowed to get syncronized DCC signals
@@ -185,6 +186,16 @@ class MotorDriver {
    inline void setTrackLetter(char c) {
      trackLetter = c;
    };
+    // this returns how much time has passed since the last power change. If it
+    // was really long ago (approx > 52min) advance counter approx 35 min so that
+    // we are at 18 minutes again. Times for 32 bit unsigned long.
+    inline unsigned long microsSinceLastPowerChange() {
+      unsigned long now = micros();
+      unsigned long diff = now - lastPowerChange;
+      if (diff > (1UL << (7 *sizeof(unsigned long)))) // 2^(4*7)us = 268.4 seconds
+        lastPowerChange = now - 30000000UL;           // 30 seconds ago
+      return diff;
+    };
 #ifdef ANALOG_READ_INTERRUPT
    bool sampleCurrentFromHW();
    void startCurrentFromHW();
@@ -202,6 +213,7 @@ class MotorDriver {
    bool dualSignal;       // true to use signalPin2
    bool invertBrake;       // brake pin passed as negative means pin is inverted
    bool invertPower;       // power pin passed as negative means pin is inverted
+    bool invertFault;       // fault pin passed as negative means pin is inverted
    
    // Raw to milliamp conversion factors avoiding float data types.
    // Milliamps=rawADCreading * sensefactorInternal / senseScale
@@ -215,8 +227,8 @@ class MotorDriver {
    int rawCurrentTripValue;
    // current sampling
    POWERMODE powerMode;
-    unsigned long lastSampleTaken;
-    unsigned int sampleDelay;
+    bool overloadNow = false;
+    unsigned long lastPowerChange; // timestamp in microseconds
    int progTripValue;
    int  lastCurrent;
 #ifdef ANALOG_READ_INTERRUPT
@@ -226,10 +238,19 @@ class MotorDriver {
    int maxmA;
    int tripmA;

-    // Wait times for power management. Unit: milliseconds
-    static const int  POWER_SAMPLE_ON_WAIT = 100;
-    static const int  POWER_SAMPLE_OFF_WAIT = 1000;
-    static const int  POWER_SAMPLE_OVERLOAD_WAIT = 20;
+    // Times for overload management. Unit: microseconds.
+    // Base for wait time until power is turned on again
+    static const unsigned long POWER_SAMPLE_OVERLOAD_WAIT =       100UL;
+    // Time after we consider all faults old and forgotten
+    static const unsigned long POWER_SAMPLE_ALL_GOOD =        5000000UL;
+    // How long to ignore fault pin if current is under limit
+    static const unsigned long POWER_SAMPLE_IGNORE_FAULT_LOW =  50000UL;
+    // How long to ignore fault pin if current is higher than limit
+    static const unsigned long POWER_SAMPLE_IGNORE_FAULT_HIGH =  5000UL;
+    // How long to wait between overcurrent and turning off
+    static const unsigned long POWER_SAMPLE_OFF_DELAY =         10000UL;
+    // Upper limit for retry period
+    static const unsigned long POWER_SAMPLE_RETRY_MAX =      10000000UL;
    
    // Trip current for programming track, 250mA. Change only if you really
    // need to be non-NMRA-compliant because of decoders that are not either.
--- a/MotorDrivers.h
+++ b/MotorDrivers.h
@@ -1,7 +1,7 @@
 /*
- *  © 2022 Paul M. Antoine
+ *  © 2022-2023 Paul M. Antoine
 *  © 2021 Fred Decker
- *  © 2020-2022 Harald Barth
+ *  © 2020-2023 Harald Barth
 *  (c) 2020 Chris Harlow. All rights reserved.
 *  (c) 2021 Fred Decker.  All rights reserved.
 *  (c) 2020 Harald Barth. All rights reserved.
@@ -36,7 +36,7 @@
 // custom defines in config.h.

 #ifndef UNUSED_PIN     // sync define with the one in MotorDriver.h
-#define UNUSED_PIN 127 // inside int8_t
+#define UNUSED_PIN 255 // inside uint8_t
 #endif

 // The MotorDriver definition is:
@@ -60,7 +60,8 @@
 // Arduino STANDARD Motor Shield, used on different architectures:

 #if defined(ARDUINO_ARCH_SAMD) || defined(ARDUINO_ARCH_STM32)
-// Setup for SAMD21 Sparkfun DEV board using Arduino standard Motor Shield R3 (MUST be R3
+// Standard Motor Shield definition for 3v3 processors (other than the ESP32)
+// Setup for SAMD21 Sparkfun DEV board MUST use Arduino Motor Shield R3 (MUST be R3
 // for 3v3 compatibility!!) senseFactor for 3.3v systems is 1.95 as calculated when using
 // 10-bit A/D samples, and for 12-bit samples it's more like 0.488, but we probably need
 // to tweak both these
@@ -70,15 +71,27 @@
 #define SAMD_STANDARD_MOTOR_SHIELD STANDARD_MOTOR_SHIELD
 #define STM32_STANDARD_MOTOR_SHIELD STANDARD_MOTOR_SHIELD

+// EX 8874 based shield connected to a 3V3 system with 12-bit (4096) ADC
+#define EX8874_SHIELD F("EX8874"), \
+ new MotorDriver( 3, 12, UNUSED_PIN, 9, A0, 1.27, 5000, A4), \
+ new MotorDriver(11, 13, UNUSED_PIN, 8, A1, 1.27, 5000, A5)
+
+
 #elif defined(ARDUINO_ARCH_ESP32)
 // STANDARD shield on an ESPDUINO-32 (ESP32 in Uno form factor). The shield must be eiter the
 // 3.3V compatible R3 version or it has to be modified to not supply more than 3.3V to the
 // analog inputs. Here we use analog inputs A2 and A3 as A0 and A1 are wired in a way so that
 // they are not useable at the same time as WiFi (what a bummer). The numbers below are the
 // actual GPIO numbers. In comments the numbers the pins have on an Uno.
-#define STANDARD_MOTOR_SHIELD F("STANDARD_MOTOR_SHIELD"),                                                 \
-    new MotorDriver(25/* 3*/, 19/*12*/, UNUSED_PIN, 13/*9*/, 35/*A2*/, 0.70, 1500, UNUSED_PIN), \
-    new MotorDriver(23/*11*/, 18/*13*/, UNUSED_PIN, 12/*8*/, 34/*A3*/, 0.70, 1500, UNUSED_PIN)
+#define STANDARD_MOTOR_SHIELD F("STANDARD_MOTOR_SHIELD"), \
+ new MotorDriver(25/* 3*/, 19/*12*/, UNUSED_PIN, 13/*9*/, 35/*A2*/, 0.70, 1500, UNUSED_PIN), \
+ new MotorDriver(23/*11*/, 18/*13*/, UNUSED_PIN, 12/*8*/, 34/*A3*/, 0.70, 1500, UNUSED_PIN)
+
+// EX 8874 based shield connected to a 3.3V system (like ESP32) and 12bit (4096) ADC
+// numbers are GPIO numbers. comments are UNO form factor shield pin numbers
+#define EX8874_SHIELD F("EX8874"),\
+ new MotorDriver(25/* 3*/, 19/*12*/, UNUSED_PIN, 13/*9*/, 35/*A2*/, 1.27, 5000, 36 /*A4*/), \
+ new MotorDriver(23/*11*/, 18/*13*/, UNUSED_PIN, 12/*8*/, 34/*A3*/, 1.27, 5000, 39 /*A5*/)

 #else
 // STANDARD shield on any Arduino Uno or Mega compatible with the original specification.
@@ -88,6 +101,12 @@
 #define BRAKE_PWM_SWAPPED_MOTOR_SHIELD F("BPS_MOTOR_SHIELD"),                                       \
                              new MotorDriver(-9 , 12, UNUSED_PIN, -3, A0, 2.99, 1500, UNUSED_PIN), \
                              new MotorDriver(-8 , 13, UNUSED_PIN,-11, A1, 2.99, 1500, UNUSED_PIN)
+
+// EX 8874 based shield connected to a 5V system (like Arduino) and 10bit (1024) ADC
+#define EX8874_SHIELD F("EX8874"), \
+ new MotorDriver( 3, 12, UNUSED_PIN, 9, A0, 5.08, 5000, A4), \
+ new MotorDriver(11, 13, UNUSED_PIN, 8, A1, 5.08, 5000, A5)
+
 #endif

 // Pololu Motor Shield
--- a/SerialManager.cpp
+++ b/SerialManager.cpp
@@ -87,6 +87,9 @@ void SerialManager::init() {
    delay(1000);
  }
 #endif
+#ifdef SABERTOOTH
+  Serial2.begin(9600, SERIAL_8N1, 16, 17); // GPIO 16 RXD2; GPIO 17 TXD2 on ESP32
+#endif
 }

 void SerialManager::broadcast(char * stringBuffer) {
--- a/TrackManager.cpp
+++ b/TrackManager.cpp
@@ -33,8 +33,9 @@
        FOR_EACH_TRACK(t) \
            if (trackMode[t]==findmode) \
                track[t]->function;
-
+#ifndef DISABLE_PROG
 const int16_t HASH_KEYWORD_PROG = -29718;
+#endif
 const int16_t HASH_KEYWORD_MAIN = 11339;
 const int16_t HASH_KEYWORD_OFF = 22479;  
 const int16_t HASH_KEYWORD_DC = 2183;  
@@ -116,7 +117,11 @@ void TrackManager::Setup(const FSH * shieldname,
    
    // Default the first 2 tracks (which may be null) and perform HA waveform check.
    setTrackMode(0,TRACK_MODE_MAIN);
+#ifndef DISABLE_PROG
    setTrackMode(1,TRACK_MODE_PROG);
+#else
+    setTrackMode(1,TRACK_MODE_MAIN);
+#endif
  
  // TODO Fault pin config for odd motor boards (example pololu)
  // MotorDriver::commonFaultPin = ((mainDriver->getFaultPin() == progDriver->getFaultPin())
@@ -198,7 +203,11 @@ bool TrackManager::setTrackMode(byte trackToSet, TRACK_MODE mode, int16_t dcAddr
      pinMode(p.invpin, OUTPUT); // gpio_reset_pin may reset to input
    }
 #endif
+#ifndef DISABLE_PROG
    if (mode==TRACK_MODE_PROG) {
+#else
+    if (false) {
+#endif
      // only allow 1 track to be prog
      FOR_EACH_TRACK(t)
 	if (trackMode[t]==TRACK_MODE_PROG && t != trackToSet) {
@@ -306,8 +315,10 @@ bool TrackManager::parseJ(Print *stream, int16_t params, int16_t p[])
    if (params==2  && p[1]==HASH_KEYWORD_MAIN) // <= id MAIN>
        return setTrackMode(p[0],TRACK_MODE_MAIN);
    
+#ifndef DISABLE_PROG
    if (params==2  && p[1]==HASH_KEYWORD_PROG) // <= id PROG>
        return setTrackMode(p[0],TRACK_MODE_PROG);
+#endif
    
    if (params==2  && p[1]==HASH_KEYWORD_OFF) // <= id OFF>
        return setTrackMode(p[0],TRACK_MODE_OFF);
@@ -332,9 +343,11 @@ void TrackManager::streamTrackState(Print* stream, byte t) {
  case TRACK_MODE_MAIN:
      format=F("<= %c MAIN>\n");
      break;
+#ifndef DISABLE_PROG
  case TRACK_MODE_PROG:
      format=F("<= %c PROG>\n");
      break;
+#endif
  case TRACK_MODE_OFF:
      format=F("<= %c OFF>\n");
      break;
@@ -357,8 +370,10 @@ void TrackManager::streamTrackState(Print* stream, byte t) {
 byte TrackManager::nextCycleTrack=MAX_TRACKS;

 void TrackManager::loop() {
-    DCCWaveform::loop(); 
-    DCCACK::loop(); 
+    DCCWaveform::loop();
+#ifndef DISABLE_PROG
+    DCCACK::loop();
+#endif
    bool dontLimitProg=DCCACK::isActive() || progTrackSyncMain || progTrackBoosted;
    nextCycleTrack++;
    if (nextCycleTrack>lastTrack) nextCycleTrack=0;
--- a/TrackManager.h
+++ b/TrackManager.h
@@ -84,8 +84,15 @@ class TrackManager {

    static int16_t joinRelay;
    static bool progTrackSyncMain;  // true when prog track is a siding switched to main
-     static bool progTrackBoosted;   // true when prog track is not current limited
-    
+    static bool progTrackBoosted;   // true when prog track is not current limited
+
+#ifdef DEBUG_ADC
+  public:
+#else
+  private:
+#endif
+    static MotorDriver* track[MAX_TRACKS];
+
  private:
    static void addTrack(byte t, MotorDriver* driver);
    static byte lastTrack;
@@ -93,7 +100,6 @@ class TrackManager {
    static POWERMODE mainPowerGuess;
    static void applyDCSpeed(byte t);

-    static MotorDriver* track[MAX_TRACKS];
    static TRACK_MODE trackMode[MAX_TRACKS]; 
    static int16_t trackDCAddr[MAX_TRACKS];  // dc address if TRACK_MODE_DC or TRACK_MODE_DCX
 #ifdef ARDUINO_ARCH_ESP32
--- a/Turnouts.cpp
+++ b/Turnouts.cpp
@@ -250,6 +250,7 @@
      }
    }
    tt = (Turnout *)new ServoTurnout(id, vpin, thrownPosition, closedPosition, profile, closed);
+    DIAG(F("Turnout 0x%x size %d size %d"), tt, sizeof(Turnout),sizeof(struct TurnoutData));
    IODevice::writeAnalogue(vpin, closed ? closedPosition : thrownPosition, PCA9685::Instant);
    return tt;
 #else
--- a/Turnouts.h
+++ b/Turnouts.h
@@ -69,10 +69,12 @@ protected:
    uint16_t id;
  } _turnoutData;  // 3 bytes

+#ifndef DISABLE_EEPROM
  // Address in eeprom of first byte of the _turnoutData struct (containing the closed flag).
  // Set to zero if the object has not been saved in EEPROM, e.g. for newly created Turnouts, and 
  // for all LCN turnouts.
  uint16_t _eepromAddress = 0;
+#endif

  // Pointer to next turnout on linked list.
  Turnout *_nextTurnout = 0;
--- a/WiThrottle.cpp
+++ b/WiThrottle.cpp
@@ -235,6 +235,10 @@ int WiThrottle::getLocoId(byte * cmd) {
 void WiThrottle::multithrottle(RingStream * stream, byte * cmd){ 
  char throttleChar=cmd[1];
  int locoid=getLocoId(cmd+3); // -1 for *
+  if (locoid > 10239 || locoid < -1) {
+    StringFormatter::send(stream, F("No valid DCC loco %d\n"), locoid);
+    return;
+  }
  byte * aval=cmd;
  while(*aval !=';' && *aval !='\0') aval++;
  if (*aval) aval+=2;  // skip ;>
@@ -527,10 +531,13 @@ void WiThrottle::sendRoster(Print* stream) {
  rosterSent=true;
 #ifdef EXRAIL_ACTIVE
  StringFormatter::send(stream,F("RL%d"), RMFT2::rosterNameCount);
-  for (int16_t r=0;r<RMFT2::rosterNameCount;r++) {
+  for (int16_t r=0;;r++) {
      int16_t cabid=GETHIGHFLASHW(RMFT2::rosterIdList,r*2);
-      StringFormatter::send(stream,F("]\\[%S}|{%d}|{%c"),
-      RMFT2::getRosterName(cabid),cabid,cabid<128?'S':'L');
+      if (cabid == INT16_MAX)
+	break;
+      if (cabid > 0)
+	StringFormatter::send(stream,F("]\\[%S}|{%d}|{%c"),
+			      RMFT2::getRosterName(cabid),cabid,cabid<128?'S':'L');
  }
  StringFormatter::send(stream,F("\n"));       
 #else
@@ -544,14 +551,14 @@ void WiThrottle::sendRoutes(Print* stream) {
    // first pass automations
    for (int ix=0;;ix+=2) {
        int16_t id =GETHIGHFLASHW(RMFT2::automationIdList,ix);
-        if (id==0) break;
+        if (id==INT16_MAX) break;
        const FSH * desc=RMFT2::getRouteDescription(id);
        StringFormatter::send(stream,F("]\\[A%d}|{%S}|{4"),id,desc);
    }
    // second pass routes.
    for (int ix=0;;ix+=2) {
        int16_t id=GETHIGHFLASHW(RMFT2::routeIdList,ix);
-        if (id==0) break;
+        if (id==INT16_MAX) break;
        const FSH * desc=RMFT2::getRouteDescription(id);
        StringFormatter::send(stream,F("]\\[R%d}|{%S}|{2"),id,desc);
    }
@@ -567,9 +574,13 @@ void WiThrottle::sendFunctions(Print* stream, byte loco) {
 	myLocos[loco].functionToggles=1<<2; // F2 (HORN)  is a non-toggle
        
 #ifdef EXRAIL_ACTIVE
-	const char * functionNames=(char *) RMFT2::getRosterFunctions(locoid);
-	if (!functionNames) {
-	  // no roster, use non-exrail presets as above 
+	const FSH * functionNames= RMFT2::getRosterFunctions(locoid);
+	if (functionNames == NULL) {
+	  // no roster entry for locoid, try to find default entry
+	  functionNames= RMFT2::getRosterFunctions(0);
+	}
+	if (functionNames == NULL) {
+	  // no default roster entry either, use non-exrail presets as above 
 	}
 	else if (GETFLASH(functionNames)=='\0') {
 	  // "" = Roster but no functions given
@@ -584,7 +595,7 @@ void WiThrottle::sendFunctions(Print* stream, byte loco) {
 	  fkeys=0;
 	  bool firstchar=true;
 	  for (int fx=0;;fx++) {
-	    char c=GETFLASH(functionNames+fx);
+	    char c=GETFLASH((char *)functionNames+fx);
 	    if (c=='\0') {
 	      fkeys++;
 	      break;
--- a/WifiInterface.cpp
+++ b/WifiInterface.cpp
@@ -58,6 +58,14 @@ Stream * WifiInterface::wifiStream;
 #define NUM_SERIAL 1
 #endif

+// For STM32 we need to define Serial3 in the platform specific
+// DCCTimerSTM32.cpp file, we here make the assumption that it
+// exists to link against.
+#ifdef ARDUINO_ARCH_STM32
+#if NUM_SERIAL > 2
+extern HardwareSerial Serial3;
+#endif
+#endif
 bool WifiInterface::setup(long serial_link_speed, 
                          const FSH *wifiESSID,
                          const FSH *wifiPassword,
@@ -83,6 +91,8 @@ bool WifiInterface::setup(long serial_link_speed,
 #endif

 // Other serials are tried, depending on hardware.
+// Currently only the Arduino Mega 2560 has usable Serial2
+#if defined(ARDUINO_AVR_MEGA2560)
 #if NUM_SERIAL > 1 && !defined(SERIAL2_COMMANDS)
  if (wifiUp == WIFI_NOAT)
  {
@@ -90,7 +100,10 @@ bool WifiInterface::setup(long serial_link_speed,
    wifiUp = setup(Serial2, wifiESSID, wifiPassword, hostname, port, channel);
  }
 #endif
-  
+#endif
+
+// We guess here that in all architctures that have a Serial3
+// we can use it for our purpose.
 #if NUM_SERIAL > 2 && !defined(SERIAL3_COMMANDS)
  if (wifiUp == WIFI_NOAT)
  {
--- a/config.example.h
+++ b/config.example.h
@@ -1,7 +1,7 @@
 /*
 *  © 2022 Paul M. Antoine
 *  © 2021 Neil McKechnie
- *  © 2020-2021 Harald Barth
+ *  © 2020-2023 Harald Barth
 *  © 2020-2021 Fred Decker
 *  © 2020-2021 Chris Harlow
 *  
@@ -27,6 +27,16 @@ The configuration file for DCC-EX Command Station

 **********************************************************************/

+/////////////////////////////////////////////////////////////////////////////////////
+// If you want to add your own motor driver definition(s), add them here
+//   For example MY_SHIELD with display name "MINE":
+//   (remove comment start and end marker if you want to edit and use that)
+/* 
+#define MY_SHIELD F("MINE"), \
+ new MotorDriver( 3, 12, UNUSED_PIN, 9, A0, 5.08, 3000, A4), \
+ new MotorDriver(11, 13, UNUSED_PIN, 8, A1, 5.08, 1500, A5)
+*/
+
 /////////////////////////////////////////////////////////////////////////////////////
 //  NOTE: Before connecting these boards and selecting one in this software
 //        check the quick install guides!!! Some of these boards require a voltage
@@ -34,15 +44,15 @@ The configuration file for DCC-EX Command Station
 //        the correct resistor could damage the sense pin on your Arduino or destroy
 //        the device.
 //
-// DEFINE MOTOR_SHIELD_TYPE BELOW ACCORDING TO THE FOLLOWING TABLE:
+// DEFINE MOTOR_SHIELD_TYPE BELOW. THESE ARE EXAMPLES. FULL LIST IN MotorDrivers.h
 //
 //  STANDARD_MOTOR_SHIELD : Arduino Motor shield Rev3 based on the L298 with 18V 2A per channel
 //  POLOLU_MOTOR_SHIELD   : Pololu MC33926 Motor Driver (not recommended for prog track)
-//  POLOLU_TB9051FTG      : Pololu Dual TB9051FTG Motor Driver
 //  FUNDUMOTO_SHIELD      : Fundumoto Shield, no current sensing (not recommended, no short protection)
 //  FIREBOX_MK1           : The Firebox MK1                    
 //  FIREBOX_MK1S          : The Firebox MK1S
 //  IBT_2_WITH_ARDUINO    : Arduino Motor Shield for PROG and IBT-2 for MAIN
+//  EX8874_SHIELD         : DCC-EX TI DRV8874 based motor shield
 //   |
 //   +-----------------------v
 //
@@ -128,7 +138,7 @@ The configuration file for DCC-EX Command Station
 //OR define OLED_DRIVER width,height[,address] in pixels (address auto detected if not supplied)
 // 128x32 or 128x64 I2C SSD1306-based devices are supported.
 // Use 132,64 for a SH1106-based I2C device with a 128x64 display.
-// #define OLED_DRIVER 128,32,0x3c
+// #define OLED_DRIVER 0x3c,128,32

 // Define scroll mode as 0, 1 or 2
 //  *  #define SCROLLMODE 0 is scroll continuous (fill screen if poss),
@@ -141,7 +151,7 @@ The configuration file for DCC-EX Command Station
 //
 // If you do not need the EEPROM at all, you can disable all the code that saves
 // data in the EEPROM. You might want to do that if you are in a Arduino UNO
-// and want to use the EX-RAIL automation. Otherwise you do not have enough RAM
+// and want to use the EXRAIL automation. Otherwise you do not have enough RAM
 // to do that. Of course, then none of the EEPROM related commands work.
 //
 // EEPROM does not work on ESP32. So on ESP32, EEPROM will always be disabled,
@@ -149,6 +159,17 @@ The configuration file for DCC-EX Command Station
 //
 // #define DISABLE_EEPROM

+/////////////////////////////////////////////////////////////////////////////////////
+// DISABLE PROG
+//
+// If you do not need programming capability, you can disable all programming related
+// commands. You might want to do that if you are using an Arduino UNO and still want
+// to use EXRAIL automation, as the Uno is lacking in RAM and Flash to run both.
+// 
+// Note this disables all programming functionality, including EXRAIL.
+//
+// #define DISABLE_PROG
+
 /////////////////////////////////////////////////////////////////////////////////////
 // REDEFINE WHERE SHORT/LONG ADDR break is. According to NMRA the last short address
 // is 127 and the first long address is 128. There are manufacturers which have
@@ -224,5 +245,15 @@ The configuration file for DCC-EX Command Station
 //
 //#define SERIAL_BT_COMMANDS

+// SABERTOOTH
+//
+// This is a very special option and only useful if you happen to have a
+// sabertooth motor controller from dimension engineering configured to
+// take commands from and ESP32 via serial at 9600 baud from GPIO17 (TX)
+// and GPIO16 (RX, currently unused).
+// The number defined is the DCC address for which speed controls are sent
+// to the sabertooth controller _as_well_. Default: Undefined.
+//
+//#define SABERTOOTH 1

 /////////////////////////////////////////////////////////////////////////////////////
--- a/config.h.txt
+++ b/config.h.txt
@@ -1,169 +0,0 @@
-/**********************************************************************
-
-Config.h
-COPYRIGHT (c) 2013-2016 Gregg E. Berman
-COPYRIGHT (c) 2020 Fred Decker
-
-The configuration file for DCC++ EX Command Station
-
-**********************************************************************/
-/////////////////////////////////////////////////////////////////////////////////////
-//  NOTE: Before connecting these boards and selecting one in this software
-//        check the quick install guides!!! Some of these boards require a voltage
-//        generating resitor on the current sense pin of the device. Failure to select
-//        the correct resistor could damage the sense pin on your Arduino or destroy
-//        the device.
-//
-// DEFINE MOTOR_SHIELD_TYPE BELOW ACCORDING TO THE FOLLOWING TABLE:
-//
-//  STANDARD_MOTOR_SHIELD : Arduino Motor shield Rev3 based on the L298 with 18V 2A per channel
-//  POLOLU_MOTOR_SHIELD   : Pololu MC33926 Motor Driver (not recommended for prog track)
-//  FUNDUMOTO_SHIELD      : Fundumoto Shield, no current sensing (not recommended, no short protection)
-//  FIREBOX_MK1           : The Firebox MK1                    
-//  FIREBOX_MK1S          : The Firebox MK1S    
-//   |
-//   +-----------------------v
-//
-// #define STANDARD_MOTOR_SHIELD F("STANDARD_MOTOR_SHIELD"),                                              
-//                               new MotorDriver(3, 12, UNUSED_PIN, 9, A0, 0.488, 1500, UNUSED_PIN),
-//                               new MotorDriver(11, 13, UNUSED_PIN, 8, A1, 0.488, 1500, UNUSED_PIN)
-
-#define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// The IP port to talk to a WIFI or Ethernet shield.
-//
-#define IP_PORT 2560
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// NOTE: Only supported on Arduino Mega
-// Set to false if you not even want it on the Arduino Mega
-//
-//#define ENABLE_WIFI true
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// DEFINE WiFi Parameters (only in effect if WIFI is on)
-//
-// If DONT_TOUCH_WIFI_CONF is set, all WIFI config will be done with
-// the <+> commands and this sketch will not change anything over
-// AT commands and the other WIFI_* defines below do not have any effect.
-//#define DONT_TOUCH_WIFI_CONF
-//
-// WIFI_SSID is the network name IF you want to use your existing home network.
-// Do NOT change this if you want to use the WiFi in Access Point (AP) mode. 
-//
-// If you do NOT set the WIFI_SSID, the WiFi chip will first try
-// to connect to the previously configured network and if that fails
-// fall back to Access Point mode. The SSID of the AP will be
-// automatically set to DCCEX_*.
-//
-// Your SSID may not conain ``"'' (double quote, ASCII 0x22).
-#define WIFI_SSID "Your network name"
-//
-// WIFI_PASSWORD is the network password for your home network or if
-// you want to change the password from default AP mode password
-// to the AP password you want. 
-// Your password may not conain ``"'' (double quote, ASCII 0x22).
-#define WIFI_PASSWORD "deadcafe"
-//
-// WIFI_HOSTNAME: You probably don't need to change this
-#define WIFI_HOSTNAME "dccex"
-//
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// Wifi connect timeout in milliseconds. Default is 14000 (14 seconds). You only need
-// to set this if you have an extremely slow Wifi router.
-//
-#define WIFI_CONNECT_TIMEOUT 14000
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// ENABLE_ETHERNET: Set to true if you have an Arduino Ethernet card (wired). This
-// is not for Wifi. You will then need the Arduino Ethernet library as well
-//
-//#define ENABLE_ETHERNET true
-
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// DEFINE STATIC IP ADDRESS *OR* COMMENT OUT TO USE DHCP
-//
-//#define IP_ADDRESS { 192, 168, 1, 31 }
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// DEFINE MAC ADDRESS ARRAY FOR ETHERNET COMMUNICATIONS INTERFACE
-//
-// Uncomment to use with Ethernet Shields
-//
-// Ethernet Shields do not have have a MAC address in hardware. There may be one on 
-// a sticker on the Shield that you should use. Otherwise choose one of the ones below
-// Be certain that no other device on your network has this same MAC address!
-//
-// 52:b8:8a:8e:ce:21
-// e3:e9:73:e1:db:0d
-// 54:2b:13:52:ac:0c
-
-// NOTE: This is not used with ESP8266 WiFi modules.
-
-//#define MAC_ADDRESS { 0x52, 0xB8, 0x8A, 0x8E, 0xCE, 0x21 }      // MAC address of your networking card found on the sticker on your card or take one from above
-
-// 
-// #define MAC_ADDRESS {  0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xEF }
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// DEFINE LCD SCREEN USAGE BY THE BASE STATION
-//
-// Note: This feature requires an I2C enabled LCD screen using a Hitachi  HD44780
-//       controller and a PCF8574 based I2C 'backpack',
-//       OR an I2C Oled screen based on SSD1306 (128x64 or 128x32) controller,
-//       OR an I2C Oled screen based on SH1106 (132x64) controller.
-// To enable, uncomment one of the lines below
-
-// define LCD_DRIVER for I2C LCD address 0x3f,16 cols, 2 rows
-//#define LCD_DRIVER  {SubBus_4,0x27},20,4
-
-//OR define OLED_DRIVER width,height in pixels (address auto detected) 
-#if defined(ARDUINO_ARCH_STM32) 
-#define OLED_DRIVER 0x3c, 128, 64
-#else
-#define OLED_DRIVER {SubBus_0,0x3c}, 128, 32
-#endif
-
-#define SCROLLMODE 1
-
-/////////////////////////////////////////////////////////////////////////////////////
-// DISABLE EEPROM
-//
-// If you do not need the EEPROM at all, you can disable all the code that saves
-// data in the EEPROM. You might want to do that if you are in a Arduino UNO
-// and want to use the EX-RAIL automation. Otherwise you do not have enough RAM
-// to do that. Of course, then none of the EEPROM related commands work.
-//
-#define DISABLE_EEPROM
-
-
-/////////////////////////////////////////////////////////////////////////////////////
-//
-// DEFINE TURNOUTS/ACCESSORIES FOLLOW NORM RCN-213
-//
-// According to norm RCN-213 a DCC packet with a 1 is closed/straight
-// and one with a 0 is thrown/diverging.  In DCC++ Classic, and in previous
-// versions of DCC++EX, a turnout throw command was implemented in the packet as 
-// '1' and a close command as '0'. The #define below makes the states
-// match with the norm.  But we don't want to cause havoc on existent layouts,
-// so we define this only for new installations. If you don't want this,
-// don't add it to your config.h.
-//#define DCC_TURNOUTS_RCN_213
-
-// The following #define likewise inverts the behaviour of the <a> command 
-// for triggering DCC Accessory Decoders, so that <a addr subaddr 0> generates a 
-// DCC packet with D=1 (close turnout) and <a addr subaddr 1> generates D=0 
-// (throw turnout).
-//#define DCC_ACCESSORY_RCN_213
-
-/////////////////////////////////////////////////////////////////////////////////////
--- a/defines.h
+++ b/defines.h
@@ -147,7 +147,8 @@
  #ifndef I2C_USE_WIRE
  #define I2C_USE_WIRE
  #endif
-
+  #undef NUM_SERIAL
+  #define NUM_SERIAL 3

 /* TODO when ready 
 #elif defined(ARDUINO_ARCH_RP2040)
--- a/install_via_powershell.cmd
+++ b/install_via_powershell.cmd
@@ -0,0 +1,13 @@
+@ECHO OFF
+
+FOR /f "tokens=*" %%a IN ('powershell Get-ExecutionPolicy -Scope CurrentUser') DO SET PS_POLICY=%%a
+
+IF NOT %PS_POLICY=="Bypass" (
+  powershell Set-ExecutionPolicy -Scope CurrentUser Bypass
+)
+
+powershell %~dp0%installer.ps1
+
+IF NOT %PS_POLICY=="Bypass" (
+  powershell Set-ExecutionPolicy -Scope CurrentUser %PS_POLICY%
+)
--- a/installer.ps1
+++ b/installer.ps1
@@ -0,0 +1,540 @@
+<#
+# © 2023 Peter Cole
+# 
+# This file is part of EX-CommandStation
+#
+# This is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 3 of the License, or
+# (at your option) any later version.
+#
+# It is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with CommandStation.  If not, see <https://www.gnu.org/licenses/>.
+#>
+
+<############################################
+For script errors set ExecutionPolicy:
+Set-ExecutionPolicy -Scope CurrentUser -ExecutionPolicy Bypass
+############################################>
+
+<############################################
+Optional command line parameters:
+  $buildDirectory - specify an existing directory rather than generating a new unique one
+  $configDirectory - specify a directory containing existing files as per $configFiles
+############################################>
+Param(
+  [Parameter()]
+  [String]$buildDirectory,
+  [Parameter()]
+  [String]$configDirectory
+)
+
+<############################################
+Define global parameters here such as known URLs etc.
+############################################>
+$installerVersion = "v0.0.8"
+$configFiles = @("config.h", "myAutomation.h", "myHal.cpp", "mySetup.h")
+$wifiBoards = @("arduino:avr:mega", "esp32:esp32:esp32")
+$userDirectory = $env:USERPROFILE + "\"
+$gitHubAPITags = "https://api.github.com/repos/DCC-EX/CommandStation-EX/git/refs/tags"
+$gitHubURLPrefix = "https://github.com/DCC-EX/CommandStation-EX/archive/"
+if ((Get-WmiObject win32_operatingsystem | Select-Object osarchitecture).osarchitecture -eq "64-bit") {
+  $arduinoCLIURL = "https://downloads.arduino.cc/arduino-cli/arduino-cli_latest_Windows_64bit.zip"
+  $arduinoCLIZip = $userDirectory + "Downloads\" + "arduino-cli_latest_Windows_64bit.zip"
+} else {
+  $arduinoCLIURL = "https://downloads.arduino.cc/arduino-cli/arduino-cli_latest_Windows_32bit.zip"
+  $arduinoCLIZip = $userDirectory + "Downloads\" + "arduino-cli_latest_Windows_32bit.zip"
+}
+$arduinoCLIDirectory = $userDirectory + "arduino-cli"
+$arduinoCLI = $arduinoCLIDirectory + "\arduino-cli.exe"
+
+<############################################
+List of supported devices with FQBN in case clones used that aren't detected
+############################################>
+$supportedDevices = @(
+  @{
+    name = "Arduino Mega or Mega 2560"
+    fqbn = "arduino:avr:mega"
+  },
+  @{
+    name = "Arduino Nano"
+    fqbn = "arduino:avr:nano"
+  },
+  @{
+    name = "Arduino Uno"
+    fqbn = "arduino:avr:uno"
+  },
+  @{
+    name = "ESP32 Dev Module"
+    fqbn = "esp32:esp32:esp32"
+  }
+)
+
+<############################################
+List of supported displays
+############################################>
+$displayList = @(
+  @{
+    option = "LCD 16 columns x 2 rows"
+    configLine = "#define LCD_DRIVER  0x27,16,2"
+  },
+  @{
+    option = "LCD 16 columns x 4 rows"
+    configLine = "#define LCD_DRIVER  0x27,16,4"
+  },
+  @{
+    option = "OLED 128 x 32"
+    configLine = "#define OLED_DRIVER 128,32"
+  },
+  @{
+    option = "OLED 128 x 64"
+    configLine = "#define OLED_DRIVER 128,64"
+  }
+)
+
+<############################################
+Basics of config.h
+############################################>
+$configLines = @(
+  "/*",
+  "This config.h file was generated by the DCC-EX PowerShell installer $installerVersion",
+  "*/",
+  "",
+  "// Define standard motor shield",
+  "#define MOTOR_SHIELD_TYPE STANDARD_MOTOR_SHIELD",
+  ""
+)
+
+<############################################
+Set default action for progress indicators, warnings, and errors
+############################################>
+$global:ProgressPreference = "SilentlyContinue"
+$global:WarningPreference = "SilentlyContinue"
+$global:ErrorActionPreference = "SilentlyContinue"
+
+<############################################
+If $buildDirectory not provided, generate a new time/date stamp based directory to use
+############################################>
+if (!$PSBoundParameters.ContainsKey('buildDirectory')) {
+  $buildDate = Get-Date -Format 'yyyyMMdd-HHmmss'
+  $buildDirectory = $userDirectory + "EX-CommandStation-Installer\" + $buildDate
+}
+$commandStationDirectory = $buildDirectory + "\CommandStation-EX"
+
+<############################################
+Write out intro message and prompt to continue
+############################################>
+@"
+Welcome to the DCC-EX PowerShell installer for EX-CommandStation ($installerVersion)
+
+Current installer options:
+
+- EX-CommandStation will be built in $commandStationDirectory
+- Arduino CLI will downloaded and extracted to $arduinoCLIDirectory
+
+Before continuing, please ensure:
+
+- Your computer is connected to the internet
+- The device you wish to install EX-CommandStation on is connected to a USB port
+
+This installer will obtain the Arduino CLI (if not already present), and then download and install your chosen version of EX-CommandStation
+
+"@
+
+<############################################
+Prompt user to confirm all is ready to proceed
+############################################>
+$confirmation = Read-Host "Enter 'Y' or 'y' then press <Enter> to confirm you are ready to proceed, any other key to exit"
+if ($confirmation -ne "Y" -and $confirmation -ne "y") {
+  Exit
+}
+
+<############################################
+See if we have the Arduino CLI already, otherwise download and extract it
+############################################>
+if (!(Test-Path -PathType Leaf -Path $arduinoCLI)) {
+  if (!(Test-Path -PathType Container -Path $arduinoCLIDirectory)) {
+    try {
+      New-Item -ItemType Directory -Path $arduinoCLIDirectory | Out-Null
+    }
+    catch {
+      Write-Output "Arduino CLI does not exist and cannot create directory $arduinoCLIDirectory"
+      Exit
+    }
+  }
+  Write-Output "`r`nDownloading and extracting Arduino CLI"
+  try {
+    Invoke-WebRequest -Uri $arduinoCLIURL -OutFile $arduinoCLIZip
+  }
+  catch {
+    Write-Output "Failed to download Arduino CLI"
+    Exit
+  }
+  try {
+    Expand-Archive -Path $arduinoCLIZip -DestinationPath $arduinoCLIDirectory -Force
+  }
+  catch {
+    Write-Output "Failed to extract Arduino CLI"
+  }
+} else {
+  Write-Output "`r`nArduino CLI already downloaded, ensuring it is up to date and you have a board connected"
+}
+
+<############################################
+Make sure Arduino CLI core index updated and list of boards populated
+############################################>
+# Need to do an initial board list to download everything first
+try {
+  & $arduinoCLI core update-index | Out-Null
+}
+catch {
+  Write-Output "Failed to update Arduino CLI core index"
+  Exit
+}
+# Need to do an initial board list to download everything first
+try {
+  & $arduinoCLI board list | Out-Null
+}
+catch {
+  Write-Output "Failed to update Arduino CLI board list"
+  Exit
+}
+
+<############################################
+Identify available board(s)
+############################################>
+try {
+  $boardList = & $arduinoCLI board list --format jsonmini | ConvertFrom-Json
+}
+catch {
+  Write-Output "Failed to obtain list of boards"
+  Exit
+}
+
+<############################################
+Get user to select board
+############################################>
+if ($boardList.count -eq 0) {
+  Write-Output "Could not find any attached devices, please ensure your device is plugged in to a USB port and Windows recognises it"
+  Exit
+} else {
+@"
+
+Devices attached to COM ports:
+------------------------------
+"@
+
+  $boardSelect = 1
+  foreach ($board in $boardList) {
+    if ($board.matching_boards.name) {
+      $boardName = $board.matching_boards.name
+    } else {
+      $boardName = "Unknown device"
+    }
+    $port = $board.port.address
+    Write-Output "$boardSelect - $boardName on port $port"
+    $boardSelect++
+  }
+  Write-Output "$boardSelect - Exit"
+  $userSelection = 0
+  do {
+    [int]$userSelection = Read-Host "`r`nSelect the device to use from the list above"
+  } until (
+    (($userSelection -ge 1) -and ($userSelection -le ($boardList.count + 1)))
+  )
+  if ($userSelection -eq ($boardList.count + 1)) {
+    Write-Output "Exiting installer"
+    Exit
+  } else {
+    $selectedBoard = $userSelection - 1
+  }
+}
+
+<############################################
+If the board is unknown, need to choose which one
+############################################>
+if ($null -eq $boardList[$selectedBoard].matching_boards.name) {
+  Write-Output "The device selected is unknown, these boards are supported:`r`n"
+  $deviceSelect = 1
+  foreach ($device in $supportedDevices) {
+    Write-Output "$deviceSelect - $($supportedDevices[$deviceSelect - 1].name)"
+    $deviceSelect++
+  }
+  Write-Output "$deviceSelect - Exit"
+  $userSelection = 0
+  do {
+    [int]$userSelection = Read-Host "Select the board type from the list above"
+  } until (
+    (($userSelection -ge 1) -and ($userSelection -le ($supportedDevices.count + 1)))
+  )
+  if ($userSelection -eq ($supportedDevices.count + 1)) {
+    Write-Output "Exiting installer"
+    Exit
+  } else {
+    $deviceName = $supportedDevices[$userSelection - 1].name
+    $deviceFQBN = $supportedDevices[$userSelection - 1].fqbn
+    $devicePort = $boardList[$selectedBoard].port.address
+  }
+} else {
+  $deviceName = $boardList[$selectedBoard].matching_boards.name
+  $deviceFQBN = $boardList[$selectedBoard].matching_boards.fqbn
+  $devicePort = $boardList[$selectedBoard].port.address
+}
+
+<############################################
+Get the list of tags
+############################################>
+try {
+  $gitHubTags = Invoke-RestMethod -Uri $gitHubAPITags
+}
+catch {
+  Write-Output "Failed to obtain list of available EX-CommandStation versions"
+  Exit
+}
+
+<############################################
+Get our GitHub tag list in a hash so we can sort by version numbers and extract just the ones we want
+############################################>
+$versionMatch = ".*?v(\d+)\.(\d+).(\d+)-(.*)"
+$tagList = @{}
+foreach ($tag in $gitHubTags) {
+  $tagHash = @{}
+  $tagHash["Ref"] = $tag.ref
+  $version = $tag.ref.split("/")[2]
+  $null = $version -match $versionMatch
+  $tagHash["Major"] = [int]$Matches[1]
+  $tagHash["Minor"] = [int]$Matches[2]
+  $tagHash["Patch"] = [int]$Matches[3]
+  $tagHash["Type"] = $Matches[4]
+  $tagList.Add($version, $tagHash)
+}
+
+<############################################
+Get latest two Prod and Devel for user to select
+############################################>
+$userList = @{}
+$prodCount = 1
+$devCount = 1
+$select = 1
+foreach ($tag in $tagList.Keys | Sort-Object {$tagList[$_]["Major"]},{$tagList[$_]["Minor"]},{$tagList[$_]["Patch"]} -Descending) {
+  if (($tagList[$tag]["Type"] -eq "Prod") -and $prodCount -le 2) {
+    $userList[$select] = $tag
+    $select++
+    $prodCount++
+  } elseif (($tagList[$tag]["Type"] -eq "Devel") -and $devCount -le 2) {
+    $userList[$select] = $tag
+    $select++
+    $devCount++
+  }
+}
+
+<############################################
+Display options for user to select and get the selection
+############################################>
+@"
+
+Available EX-CommandStation versions:
+-------------------------------------
+"@
+foreach ($selection in $userList.Keys | Sort-Object $selection) {
+  Write-Output "$selection - $($userList[$selection])"
+}
+Write-Output "5 - Exit"
+$userSelection = 0
+do {
+  [int]$userSelection = Read-Host "`r`nSelect the version to install from the list above (1 - 5)"
+} until (
+  (($userSelection -ge 1) -and ($userSelection -le 5))
+)
+if ($userSelection -eq 5) {
+  Write-Output "Exiting installer"
+  Exit
+} else {
+  $downloadURL = $gitHubURLPrefix + $tagList[$userList[$userSelection]]["Ref"] + ".zip"
+}
+
+<############################################
+Create build directory if it doesn't exist, or fail
+############################################>
+if (!(Test-Path -PathType Container -Path $buildDirectory)) {
+  try {
+    New-Item -ItemType Directory -Path $buildDirectory | Out-Null
+  }
+  catch {
+    Write-Output "Could not create build directory $buildDirectory"
+    Exit
+  }
+}
+
+<############################################
+Download the chosen version to the build directory
+############################################>
+$downladFile = $buildDirectory + "\CommandStation-EX.zip"
+Write-Output "Downloading and extracting $($userList[$userSelection])"
+try {
+  Invoke-WebRequest -Uri $downloadURL -OutFile $downladFile
+}
+catch {
+  Write-Output "Error downloading EX-CommandStation zip file"
+  Exit
+}
+
+<############################################
+If folder exists, bail out and tell user
+############################################>
+if (Test-Path -PathType Container -Path "$buildDirectory\CommandStation-EX") {
+  Write-Output "EX-CommandStation directory already exists, please ensure you have copied any user files then delete manually: $buildDirectory\CommandStation-EX"
+  Exit
+}
+
+<############################################
+Extract and rename to CommandStation-EX to allow building
+############################################>
+try {
+  Expand-Archive -Path $downladFile -DestinationPath $buildDirectory -Force
+}
+catch {
+  Write-Output "Failed to extract EX-CommandStation zip file"
+  Exit
+}
+
+$folderName = $buildDirectory + "\CommandStation-EX-" + ($userList[$userSelection] -replace "^v", "")
+try {
+  Rename-Item -Path $folderName -NewName $commandStationDirectory
+}
+catch {
+  Write-Output "Could not rename folder"
+  Exit
+}
+
+<############################################
+If config directory provided, copy files here
+############################################>
+if ($PSBoundParameters.ContainsKey('configDirectory')) {
+  if (Test-Path -PathType Container -Path $configDirectory) {
+    foreach ($file in $configFiles) {
+      if (Test-Path -PathType Leaf -Path "$configDirectory\$file") {
+        Copy-Item -Path "$configDirectory\$file" -Destination "$commandStationDirectory\$file"
+      }
+    }
+  } else {
+    Write-Output "User provided configuration directory $configDirectory does not exist, skipping"
+  }
+} else {
+
+<############################################
+If no config directory provided, prompt for display option
+############################################>
+  Write-Output "`r`nIf you have an LCD or OLED display connected, you can configure it here`r`n"
+  Write-Output "1 - I have no display, skip this step"
+  $displaySelect = 2
+  foreach ($display in $displayList) {
+    Write-Output "$displaySelect - $($displayList[$displaySelect - 2].option)"
+    $displaySelect++
+  }
+  Write-Output "$($displayList.Count + 2) - Exit"
+  do {
+    [int]$displayChoice = Read-Host "`r`nSelect a display option"
+  } until (
+    ($displayChoice -ge 1 -and $displayChoice -le ($displayList.Count + 2))
+  )
+  if ($displayChoice -eq ($displayList.Count + 2)) {
+    Exit
+  } elseif ($displayChoice -ge 2) {
+    $configLines+= "// Display configuration"
+    $configLines+= "$($displayList[$displayChoice - 2].configLine)"
+    $configLines+= "#define SCROLLMODE 1 // Alternate between pages"
+  }
+<############################################
+If device supports WiFi, prompt to configure
+############################################>
+  if ($wifiBoards.Contains($deviceFQBN)) {
+    Write-Output "`r`nYour chosen board supports WiFi`r`n"
+    Write-Output "1 - I don't want WiFi, skip this step
+2 - Configure my device as an access point I will connect to directly
+3 - Configure my device to connect to my home WiFi network
+4 - Exit"
+    do {
+      [int]$wifiChoice = Read-Host "`r`nSelect a WiFi option"
+    } until (
+      ($wifiChoice -ge 1 -and $wifiChoice -le 4)
+    )
+    if ($wifiChoice -eq 4) {
+      Exit
+    } elseif ($wifiChoice -ne 1) {
+      $configLines+= ""
+      $configLines+= "// WiFi configuration"
+      $configLines+= "#define ENABLE_WIFI true"
+      $configLines+= "#define IP_PORT 2560"
+      $configLines+= "#define WIFI_HOSTNAME ""dccex"""
+      $configLines+= "#define WIFI_CHANNEL 1"
+      if ($wifiChoice -eq 2) {
+        $configLines+= "#define WIFI_SSID ""Your network name"""
+        $configLines+= "#define WIFI_PASSWORD ""Your network passwd"""
+      }
+      if ($wifiChoice -eq 3) {
+        $wifiSSID = Read-Host "Please enter the SSID of your home network here"
+        $wifiPassword = Read-Host "Please enter your home network WiFi password here"
+        $configLines+= "#define WIFI_SSID ""$($wifiSSID)"""
+        $configLines+= "#define WIFI_PASSWORD ""$($wifiPassword)"""
+      }
+    }
+  }
+
+<############################################
+Write out config.h to a file here only if config directory not provided
+############################################>
+  $configH = $commandStationDirectory + "\config.h"
+  try {
+    $configLines | Out-File -FilePath $configH -Encoding ascii
+  }
+  catch {
+    Write-Output "Error writing config file to $configH"
+    Exit
+  }
+}
+
+<############################################
+Install core libraries for the platform
+############################################>
+$platformArray = $deviceFQBN.split(":")
+$platform = $platformArray[0] + ":" + $platformArray[1]
+try {
+  & $arduinoCLI core install $platform
+}
+catch {
+  Write-Output "Error install core libraries"
+  Exit
+}
+
+<############################################
+Upload the sketch to the selected board
+############################################>
+#$arduinoCLI upload -b fqbn -p port $commandStationDirectory
+Write-Output "Compiling and uploading to $deviceName on $devicePort"
+try {
+  $output = & $arduinoCLI compile -b $deviceFQBN -u -t -p $devicePort $commandStationDirectory --format jsonmini | ConvertFrom-Json
+}
+catch {
+  Write-Output "Failed to compile"
+  Exit
+}
+if ($output.success -eq "True") {
+  Write-Output "`r`nCongratulations! DCC-EX EX-CommandStation $($userList[$userSelection]) has been installed on your $deviceName`r`n"
+} else {
+  Write-Output "`r`nThere was an error installing $($userList[$userSelection]) on your $($deviceName), please take note of the errors provided:`r`n"
+  if ($null -ne $output.compiler_err) {
+    Write-Output "Compiler error: $($output.compiler_err)`r`n"
+  }
+  if ($null -ne $output.builder_result) {
+    Write-Output "Builder result: $($output.builder_result)`r`n"
+  }
+}
+
+Write-Output "`r`nPress any key to exit the installer"
+[void][System.Console]::ReadKey($true)
--- a/version.h
+++ b/version.h
@@ -4,7 +4,23 @@
 #include "StringFormatter.h"


-#define VERSION "4.2.41"
+#define VERSION "4.2.54"
+// 4.2.54 - EX8874 shield in config.example.h
+//        - Fix: Better warnings for pin number errors
+//        - Fix: Default roster list possible in Withrottle and <jR>
+//        - Fix: Pin handling supports pins up to 254
+// 4.2.53 - Fix: Fault pin handling made more straight forward
+// 4.2.52 - Experimental support for sabertooth motor controller on ESP32
+// 4.2.51 - Add DISABLE_PROG to disable programming to save RAM/Flash
+// 4.2.50 - Fixes: estop all, turnout eeprom, cab ID check
+// 4.2.49 - Exrail SPEED take notice of external direction change 
+// 4.2.48 - BROADCAST/WITHROTTLE Exrail macros 
+// 4.2.47 - Correct response to <JA 0>
+// 4.2.46 - Support boards with inverted fault pin
+// 4.2.45 - Add ONCLOCKMINS to FastClock to allow hourly repeat events
+// 4.2.44 - Add PowerShell installer EX-CommandStation-installer.exe
+// 4.2.43 - Fix STM32 set right port mode bits for analog
+// 4.2.42 - Added EXRAIL TURNOUTL Macro definition
 // 4.2.41 - Move HAl startup to ASAP in setup()
 //        - Fix DNOU8 output pin setup to all LOW  
 // 4.2.40 - Automatically detect conflicting default I2C devices and disable
@@ -72,6 +88,10 @@
 // 4.2.11 Exrail IFLOCO feature added
 // 4.2.10 SIGNAL/SIGNALH bug fix as they were inverted
 //        IO_EXIOExpander.h input speed optimisation
+//        ONCLOCK and ONCLOCKTIME command added to EXRAIL for EX-FastCLock
+//        <JC> Serial command added for EX-FastClock
+//        <jC> Broadcast added for EX-FastClock
+//        IO_EXFastClock.h added for I2C FastClock connection
 // 4.2.9 duinoNodes support
 // 4.2.8 HIGHMEM (EXRAIL support beyond 64kb)
 //       Withrottle connect/disconnect improvements
Author	SHA1	Message	Date
Harald Barth	1888073dc2	set lastPowerChange we doing the power on retry after overload	2023-06-19 08:43:50 +02:00
Harald Barth	6dd175f63b	fix power change timer micros overflow	2023-06-19 00:33:53 +02:00
Harald Barth	f83be05220	STM32: Use mask as loop variable	2023-06-18 19:26:38 +02:00
Harald Barth	cade89ba16	check ADCee::init() return value	2023-06-18 09:48:15 +02:00
Harald Barth	277825c530	versiontag	2023-06-18 09:01:32 +02:00
Harald Barth	95fe7aafe0	overload detection code cleanup	2023-06-18 08:59:37 +02:00
Harald Barth	f99deb4276	overload detection different timestamps and verbose diag	2023-06-14 22:57:28 +02:00
Harald Barth	f5d4dcb97c	new overload detection	2023-06-14 00:58:02 +02:00
Harald Barth	8a69403dda	devel release version 4.2.54	2023-06-03 22:01:14 +02:00
Harald Barth	e81d1cc93a	Better warnings for pin number errors	2023-05-29 09:48:22 +02:00
Harald Barth	82929245ed	char * / flashstring conflict	2023-05-25 14:02:28 +02:00
Harald Barth	db0e0cbf8b	Send default function list in jR as well	2023-05-25 10:29:01 +02:00
Harald Barth	803b996e0b	Merge branch 'devel' of https://github.com/DCC-EX/CommandStation-EX into devel	2023-05-25 09:29:47 +02:00
Harald Barth	5607ff7167	version	2023-05-25 09:29:42 +02:00
Harald Barth	58e62aaa81	Bug: Withrottle roster list returning empty string vs NULL	2023-05-25 09:27:41 +02:00
Harald Barth	5a9adea2b6	Bug: Withrottle roster list end was not detected	2023-05-25 08:05:07 +02:00
pmantoine	bf136d49e0	Fix Serial ports for Nucleo-144 boards	2023-05-25 08:34:20 +08:00
Harald Barth	50313ebbd2	cast to big enough type	2023-05-24 22:58:21 +02:00
Harald Barth	72bfc6abc7	INT16_MAX missing again	2023-05-24 22:57:43 +02:00
Harald Barth	342d9263d1	time stamp	2023-05-24 13:32:34 +02:00
Harald Barth	20d66fad4e	Routes, automations and roster lists: Exclude ID 0 to be presented as available	2023-05-24 13:31:18 +02:00
Harald Barth	be4235e792	Arduino Mega2560: Use timer5 as timer4 for PWM DC	2023-05-24 13:29:20 +02:00
Harald Barth	c22d789513	INT16_MAX was missing at more places	2023-05-23 18:59:03 +02:00
Harald Barth	951a6637f0	INT16_MAX is a better end of array marker than -1	2023-05-23 10:57:45 +02:00
Harald Barth	fdbcbdf418	Do not send default roster entry on withrottle but on JR	2023-05-22 22:51:35 +02:00
Harald Barth	9478c3263d	Try to find default roster entry	2023-05-22 16:39:24 +02:00
Harald Barth	16f94ecbdc	Restict where what SerialX is used	2023-05-21 20:20:32 +02:00
Harald Barth	b80d7bd517	Pin handling supports pins up to 254	2023-05-21 11:54:46 +02:00
Harald Barth	8786285624	Assume that we have enough HW serials	2023-05-20 23:57:17 +02:00
Harald Barth	132b0773ef	Fault pin handling made more straight forward	2023-05-20 23:15:15 +02:00
pmantoine	1a3d295564	Nucleo-F446RE and other serial port updates.	2023-05-20 21:50:20 +08:00
Harald Barth	3b6789ef01	Merge branch 'devel-sabertooth' into devel	2023-05-20 14:59:07 +02:00
Harald Barth	c472f48d93	Experimental support for sabertooth motor controller on ESP32	2023-05-20 14:57:00 +02:00
pmantoine	94e9c2021b	Fix config.example.h OLED_DRIVER #define	2023-05-15 11:31:44 +08:00
Harald Barth	9aad2e3206	save another 2 bytes in turnouts if eeprom is disabled	2023-05-09 14:17:30 +02:00
Harald Barth	ecc366cbd1	Merge branch '332-feature-request-add-a-no-programming-option-to-save-ram-on-uno' into devel	2023-05-09 14:11:18 +02:00
pmantoine	f4e3ca7c81	EX8874 entry for SAMD/STM32	2023-05-08 08:32:47 +08:00
Harald Barth	991bda63e0	update to production shield factors	2023-05-08 00:35:00 +02:00
Harald Barth	5164bd143c	versions	2023-05-08 00:22:31 +02:00
Harald Barth	3759fc2a1a	add checks for broken cab ID	2023-05-08 00:19:59 +02:00
Harald Barth	df7b890758	No EEPROM so you do not need this	2023-05-07 23:58:47 +02:00
Harald Barth	6d802f3a73	estop all locos in list, even last one	2023-05-05 16:14:44 +02:00
Harald Barth	9d953c70b8	use M1 and M2 instead of MD for motor control	2023-05-02 23:51:17 +02:00
Asbelos	6781e44fdd	Fix EXRAIL speed issue	2023-05-02 22:02:52 +01:00
Asbelos	a3c9800aba	Update version.h	2023-05-02 12:29:03 +01:00
Harald Barth	efdbfcb030	Add serial output for sabertooth controller	2023-05-01 20:18:32 +02:00
Asbelos	28d9843133	Broadcast changes in EXRAIlr	2023-05-01 14:25:45 +01:00
Harald Barth	4eaad2d05b	disable more PROG stuff (JOIN/UNJOIN from EXRAIL)	2023-04-23 22:45:47 +02:00
Harald Barth	72d131035e	disable more PROG stuff (all hash keywords PROG etc)	2023-04-23 20:24:29 +02:00
peteGSX	2d1e695ac7	Disable <D ACK>	2023-04-20 08:26:17 +10:00
peteGSX	e780c40b34	Disable POM OPCODE	2023-04-20 08:16:32 +10:00
peteGSX	7addb13785	Disable <R> completely	2023-04-20 07:21:32 +10:00
peteGSX	b6f8889e8c	Disable most programming functions	2023-04-20 07:08:11 +10:00
Colin Murdoch	33306219c8	Merge branch 'devel' of https://github.com/DCC-EX/CommandStation-EX into devel	2023-04-19 19:46:12 +01:00
Colin Murdoch	d857c4f2e4	Added to Copyright notice Added my name to copyright notice	2023-04-19 19:45:40 +01:00
Asbelos	70fae16ab3	Correct response to <JA 0>	2023-04-19 11:18:47 +01:00
Harald Barth	f465020e93	Support boards with inverted fault pin	2023-04-17 23:40:48 +02:00
Harald Barth	235bcc9ff0	Merge branch 'devel' into devel-invfault	2023-04-17 23:20:01 +02:00
pmantoine	d2cc60812d	Merge ESP32-fixes into DCCTimerESP	2023-04-16 15:40:27 +08:00
pmantoine	75f274e3b7	STM32 unsupported board selection error reporting	2023-04-13 15:27:22 +08:00
Colin Murdoch	ff53b90034	Update version.h Added ONCLOCKMINS for FastClock	2023-04-12 12:11:43 +01:00
Colin Murdoch	1daa0a9ba9	Merge branch 'devel-plus-fastclockaddons' into devel	2023-04-12 12:09:27 +01:00
Colin Murdoch	294b9693c5	Additions to FastClock Added ONCLOCKMINS to fastclock to allow hourly repeated events.	2023-04-12 12:07:08 +01:00
Harald Barth	16e44eb11a	Check for max 16 analog channels	2023-04-11 12:13:47 +02:00
peteGSX	4bad334875	Update version	2023-04-11 12:01:25 +10:00
peteGSX	32491854ff	Merge pull request #330 from DCC-EX:powershell-installer Powershell-installer	2023-04-11 11:59:28 +10:00
peteGSX	3e95372816	Rename installer exe	2023-04-11 11:48:35 +10:00
peteGSX	05b0fc3d2e	Add exe version	2023-04-11 10:26:15 +10:00
peteGSX	bb7cdc5422	WiFi AP mode compiles	2023-04-11 09:42:54 +10:00
peteGSX	6199cecd42	0.0.7 Ready for testing	2023-04-11 08:55:04 +10:00
peteGSX	1aae0aed0a	Working on config output	2023-04-11 05:31:44 +10:00
peteGSX	1d29be9de6	Working on 0.0.7	2023-04-10 19:52:31 +10:00
Harald Barth	bfa33a9df7	Fix STM32 set right port mode bits for analog port	2023-04-10 01:47:00 +02:00
Harald Barth	49c0a1a55a	Merge branch 'devel' of https://github.com/DCC-EX/CommandStation-EX into devel	2023-04-08 23:35:48 +02:00
Harald Barth	9b7d1ae858	STM32: Use predefined function for pinnames	2023-04-08 23:33:33 +02:00
Colin Murdoch	c11d8f6359	Add TURNOUTL Macro to EXRAIL Add TURNOUTL Macro to EXRAIL and retrospective update to version.h to record addition of EX-FastClock mods.	2023-04-08 17:22:39 +01:00
peteGSX	e7d9626a72	Fix CLI directory name	2023-04-08 08:39:42 +10:00
peteGSX	fe035f4096	Move from temp to user home dir	2023-04-08 08:38:02 +10:00
peteGSX	4d236446b0	Add core index update	2023-04-08 06:57:09 +10:00
peteGSX	a100d709ce	Install core library, add batch wrapper	2023-04-08 06:22:09 +10:00
peteGSX	2e518fcac2	Enable using existing configs	2023-04-07 19:30:15 +10:00
peteGSX	be273454bc	Merge branch 'powershell-installer' of https://github.com/DCC-EX/CommandStation-EX into powershell-installer	2023-04-07 19:04:03 +10:00
peteGSX	751b46b6bb	Initial test working!	2023-04-07 19:03:51 +10:00
peteGSX	91bc9df44e	Working on CLI commands	2023-04-07 19:03:51 +10:00
peteGSX	72ceb63913	Start getting tag list	2023-04-07 19:03:50 +10:00
peteGSX	d2c7e7fb8d	Working on logic	2023-04-07 19:03:50 +10:00
peteGSX	61db37c7ea	Got tag version and URL	2023-04-07 19:03:50 +10:00
peteGSX	3a3071f35b	Got tag list	2023-04-07 19:03:50 +10:00
peteGSX	ef3d36ae25	Figuring out commands	2023-04-07 19:03:50 +10:00
peteGSX	9f212c27bf	Initial test working!	2023-04-07 08:06:32 +10:00
peteGSX	de06c0ae3e	Working on CLI commands	2023-04-06 15:06:22 +10:00
peteGSX	18a992bf08	Start getting tag list	2023-04-06 05:31:11 +10:00
peteGSX	de6e91a778	Working on logic	2023-04-05 15:54:48 +10:00
peteGSX	b18df1405c	Got tag version and URL	2023-04-05 05:30:00 +10:00
peteGSX	305e0902f4	Got tag list	2023-04-04 19:30:59 +10:00
peteGSX	95c1b1da31	Figuring out commands	2023-04-04 15:48:11 +10:00
Harald Barth	31ecba08d8	faultPin can be inverted (from its inverted sense	2023-03-03 20:51:32 +01:00